StarTech com 1U 19in Steel Hinged Wall-Mount Bracket for Patch Panels User Guide

: June 5, 2024
: StarTech com

Table of Contents

Product Diagram (WALLMOUNTH1)
Product Dimensions
Documents / Resources

1U 19in Steel Hinged Wall-Mount Bracket for Patch Panels
Quick-Start Guide

Product Diagram (WALLMOUNTH1)

| Component| Function
---|---|---
1| Mounting Holes (4)| • Used to mount the Wall-Mount Bracket to a Wall.
• Maximum weight capacity = 8 kg (17 lb).
2| Hinged Side Panel| • Used to access the back of the installed Patch Panel.
3| Cage Nut Holes| • Used to mount a Patch Panel in the Wall-Mount Bracket.
• Maximum height = 1U.

Package Contents

Wall-Mount Bracket x 1
M6 Screws x 4
M6 Cage Nuts x 4
Plastic Washers x 4
M5-25 Flat-head Screws x 2
Concrete Wall Anchors x 2
Quick-Start Guide x 1

Requirements
For the latest requirements, please visit www.startech.com/WALLMOUNTH1

Phillips Head Screwdriver x 1
(Optional) Cage Nut Tool x 1

Installing the Wall-Mount Bracket
Warnings: If you lack the necessary expertise to attach this product to the wall, consult a professional to install the Wall-Mount Bracket or to provide specific mounting instructions for your wall structure.
Make sure that the type of wall structure and mounting hardware that you are using will properly support the mounted equipment. Failure to do so might result in personal injury and/or equipment damage. The wall structure should be capable of supporting at least four times the weight of the mounted equipment. Do not add equipment to the Wall-Mount Bracket until it is securely attached to the wall.
Adding Equipment to the Wall-Mount Bracket
Use the included M6 Cage Nuts, Screws, and Plastic Washers to install equipment into the Wall-Mount Bracket.

Insert the Wing (side) of an M6 Cage Nut into the back of the desired Cage Nut Hole.
Apply pressure by hand, or with the Cage Nut Tool, to insert the second Wing of the M6 Cage Nut into the desired Cage Nut Hole.
Repeat steps 1 and 2 to insert the desired number of Cage Nuts for the application.
Thread a Plastic Washer over an M6 Screw. Repeat until the desired number of M6 Screws have been prepared.
Align the Mounting Holes in the Equipment with the M6 Cage Nuts installed in steps 1-3.
Insert the assembled Screws through the Mounting Holes in the Equipment and into the M6 Cage Nuts.
Tighten the Screws, using a Phillips Head Screwdriver.

Accessing the Back of a Patch Panel

While supporting the weight of the Patch Panel, use a Phillips Head Screwdriver to unscrew two M6 Screws from the Cage Nuts, leaving the other two M6 Screws
attached to the side of the Wall-Mount Bracket with the Hinged Side Panel.
Note: Make sure that there is enough clearance for the Patch Panel to free swing away from the Wall-Mount Bracket, before accessing the back of the Patch Panel.
Gently swing the Patch Panel away from the Wall-Mount Bracket to gain access to the back of the Patch Panel.
Reattach the two M6 Screws removed in step 1.

Product Dimensions

Warnings

Do not exceed the weight capacity of this product. Overloading this product might result in injury or property damage. This product can support the following weight: 8 kg (17 lb.).
Make sure that the surface that you are attaching this product to can safely support the combined weight of the equipment and all of the hardware and components.
Wall structures vary, and it is important to make sure that the type of wall structure and mounting hardware that you are using will properly support the mounted equipment. Failure to do so might result in personal injury and/or equipment damage. The wall structure should be capable of supporting at least four times the weight of the mounted equipment

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders. Warranty Information
This product is backed by a two-year warranty. For further information on product warranty terms and conditions, please refer to www.startech.com/warranty. Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees, or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual rice paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.

StarTech.com Ltd.
45 Artisans Crescent
London, Ontario
N5V 5E9
Canada| StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.| StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Road
Brackmills,
Northampton
NN4 7BW
United Kingdom| StarTech.com Ltd.
Siriusdreef 17-27
2132 WT Hoofddorp
The Netherlands
---|---|---|---

To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visitwww.startech.com/support.
Manual Revision: January 19, 2022, 5:42 PM

Documents / Resources

| StarTech com 1U 19in Steel Hinged Wall-Mount Bracket for Patch Panels [pdf] User Guide
1U 19in Steel Hinged Wall-Mount Bracket for Patch Panels, Hinged Wall-Mount Bracket, Wall-Mount Bracket, Bracket
---|---