immax neo E27 Smart LED Light User Manual
- June 4, 2024
- immax neo
Table of Contents
immax neo E27 Smart LED Light User Manual
TECHNICAL SPECIFICATIONS
Protocol: Zigbee
Frequency: 2400MHz ~ 2483.5MHz
Maximum RF output power: WiFi: 10dBm – max 19dBm
Power consumption: 11W
Mains standby power supply (Pnet): 0.5W
Socket: E27
Bulb body material: plastic
Light color: RGB + CCT (warm, natural and cold white)
Color temperature: 2700K-6500K
Luminous flux: 1055lm (in a 360° sphere)
Beam angle: 240°
Input voltage: AC 230V
Average life: 25,000 hours
Color rendering index: >80Ra
Dimensions: 60mm x 120mm
Corresponds to a classic light bulb: 75W
Number of switching cycles: 100,000
Immediate lighting
Energy class (EEI): F
Power factor: >0.5
Dimming option: YES
Certificates: CE
The Gateway serves as a hub for communication between your mobile device and other smart Home devices.
The smart colour-changing LED light bulbs are used for lighting up interiors.
PAIRING LED LAMPS AND APP IMMAX NEO PRO
NOTES:
The Android version of the app follows the same principles as the iOS version;
you might encounter discrepancies between the two plat-forms, such as slightly
different on-screen commands or icons.
Updating the firmware might result in changes to the app’s functionality.
PREPARATION
-
Switch off the light with the wall switch.
-
Screw the Immax NEO LED bulb into the luminaire socket.
-
Switch on the light with the wall switch – the LED bulb should start flash. If the LED does not flash, reset it.
-
Everything is ready for pairing.
-
Open the Immax NEO PRO application.
-
Click on the “Room” icon.
-
Click on the “+” icon to add a new device.
-
In the left column, select the Immax NEO category.
-
Select the zigbee LED bulb from the products offered.
-
Select the smart gateway with which you want to pair this device
( Note: this is necessary if you have more than one smart gateway Immax NEO PRO). -
Click on the “Next Step” icon.
-
Confirm that the LED is flashing.
-
Click on the “Next step” icon.
-
Wait until the device is properly paired with the smart gateway Immax NEO PRO.
-
Enter the device name.
-
Select the room in which you want the device to be located.
-
Click “Done.”
UNPAIR EQUIPMENT FROM THE IMMAX NEO PRO SMART GATEWAY
-
Open the Immax NEO PRO application
-
Click on the “Room” icon
-
Select the device you want to unpair
-
Click on the icon in the upper right corner of “Settings”
-
Click “Remove device”
-
Select one of the options
a) Disconnect – removes the device from the Immax NEO PRO application, but device information remains stored in the Immax NEO cloud
b) Disconnect and wipe data – removes the device from the application Immax NEO PRO and from the Immax NEO cloud -
Confirm the removal of the device
IMMAX NEO LED BULB RESET
- Turn off and turn on Immax NEO LED bulb 5 times in a row. The interval between switching off and switching on should be at least 1-2 seconds.
- The LED will start flashing after a reset.
SAFETY INFORMATION
CAUTION: Keep out of reach of children. This product contains small
parts, which may cause suffocation or injury if swallowed.
WARNING: Every battery has the potential to leak harmful chemicals that
can damage skin, clothing or area where the battery is stored. To avoid the
risk of injury, do not allow any substance from the battery to come into
contact with the eyes or skin. Every battery may burst or even explode if
exposed to fire or other forms of excessive heat. Take care when handling the
batteries. To reduce the risk of injury from mishandling the batteries, take
the following precautions:
- Do not use different brands and types of batteries in the same device
- When replacing the batteries, always replace all the batteries in the device
- Do not use rechargeable or reusable batteries.
- Do not allow children to insert batteries without supervision.
- Follow the battery manufacturer’s instructions for proper battery handling and disposal.
CAUTION: The product and batteries should be disposed of at a recycling
centre. Do not dispose of them with normal household waste.
CAUTION: To ensure safe use of the product, wires must be brought at the
installation site according to valid regulations. The installation must only
be carried out by an individual with the appropriate certification in the
field of electronics. During installation or when a fault is detected, the
power cable must always be disconnected from the socket (in the case of direct
connection, the relevant circuit breaker must be switched off). Improper
installation can damage the product and cause injury.
CAUTION: Do not disassemble the product, electric shock may occur. CAUTION:
Use only the original power adapter provided with the product. Do not operate
the device if the power cord shows signs of damage. CAUTION: Follow the
instructions in the enclosed manual.
MAINTENANCE
Protect the device from contamination and soiling. Wipe the device with a soft cloth, do not use rough or coarse materials.
DO NOT USE solvents or other aggressive cleaners or chemicals.
A Declaration of Conformity has been issued for this product. More information
can be found at www.immax.cz
Manufacturer and importer:
IMMAX, Pohoří 703, 742 85 Vřesina, EU |
www.immaxneo.cz |
www.immaxneo.com
Made in P.R.C.
References
- Velkoobchod s LED technikou IMMAX | Immax.cz
- Velkoobchod s LED technikou IMMAX | Immax.cz
- Velkoobchod s LED technikou IMMAX | Immax.cz
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>