NATURE S Wind Turbine User Manual
- June 7, 2024
- NATURE S
Table of Contents
NATURE S Wind Turbine
Welcome
Congratulations on the purchase of your new Nature’s Wind Turbine, a state-of-
art wind turbine that recharges your Nature’s Generator through the wind.
Please read these instructions thoroughly prior to installation, then store
this manual in a safe place for future reference. If at any time you are
unclear about this product or require additional assistance, please do not
hesitate to contact our Customer Support line at
805-383-0003 or email us at
support@naturesgenerator.com.
Important Safety Instructions
- Read these instructions.
- Keep these instructions.
- Take note of all warnings.
- Follow all instructions.
- Place this manual in a safe place for future reference.
- Only use attachments/accessories specified by the manufacturer.
- Refer all servicing to qualified service personnel. Servicing is required when Nature’s Wind Turbine has been damaged in any way, such as cord or plug is damaged or Nature’s Wind Turbine has been dropped.
- Wait until a calm day to install the Nature’s Wind Turbine.
- Avoid the sharp edges on the blades.
- Readjust and tighten the screws and bolts as needed after installation.
- Your Nature’s Wind Turbine must be installed in accordance with this manual along with local and national building codes. Incorrect installation may void the warranty.
- Your Nature’s Wind Turbine blades spin at a potentially dangerous speed. Never approach the turbine in motion.
Warning
Mechanical Hazard
The rotating blades present the most serious mechanical hazard. The tip of the
rotating blades may be moving at a speed over 300 miles per hour. The blades
are almost invisible and may cause serious injuries. You should NOT install
the turbine where anyone could come in touch with the rotating blades.
Electrical Hazard
Nature’s Wind Turbine generates electricity and thus the inherent personal
injury from electricity exists. Be always cautious when connecting cables and
connect to Nature’s Generator.
Replacement parts
When replacement parts are required, make sure that the service technician
uses replacement parts specified by the manufacturer that have the same
characteristics as the original part. Unauthorized substitutions may result in
fire, electric shock, personal injury, or other hazards.
Safety check
After completing any service or repair to this device, ask the service
technician to perform routine safety checks to determine that your Nature’s
Wind Turbine is in the correct operating condition.
Servicing
These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock, do not perform any servicing other than
that contained in the operating instructions unless you are qualified to do
so.
Caution
Damage requiring service
Stop using the Nature’s Wind Turbine and refer servicing to qualified service
personnel under the following conditions:
• If your Nature’s Wind Turbine has been dropped or damaged in any way.
• When your Nature’s Generator exhibits a distinct change in performance.
End of life directives
Your Nature’s Wind Turbine may contain materials that are regulated for
environmental reasons. Your Nature’s Wind Turbine also contains materials that
can be recycled and reused. To help protect the environment, contact your
local authorities for information about disposal or recycling and about
finding a recycler in your area before you dispose of your Nature’s Wind
Turbine.
Unpack Your Nature’s Wind Turbine
1. Nature’s Wind Turbine main body
2. Hub
3. Nose cone
4. Blades x 5
5. 100-foot-long wind turbine cable 6. Controller box
7. This user manual
8. Accessory bag that includes.
Get to Know Your Nature’s Wind Turbine
Complete Electrical System
Your Nature’s Wind Turbine comes with a 100-foot long wind turbine cable and
controller box. It is a complete electrical system to recharge your Nature’s
Generator.
Built-in Protections
Your Nature’s Wind Turbine controller box has built-in overcurrent protection
and over-voltage protection that prevent possible damage to your Nature’s
Generator.
Grounding
Every wind turbine and turbine tower need to be grounded at the tower base.
Grounding the tower at its base may help prevent shocks to persons touching
the tower due to lightning or electrical faults. Please take the time to
review the National Electrical Code (NEC) and local building and zoning
regulations for complete requirements. Your Nature’s Wind Turbine has a
grounding cable included for this purpose.
Expandability
Your Nature’s Wind Turbine can be connected to another Nature’s Wind Turbine
to double the charging speed by using a dual controller box. Please visit
www.naturesgenerator.com or contact the
Customer Support line at 805-383-0003
or email us at
support@naturesgenerator.com.
Using Your Nature’s Wind Turbine
How to choose the location
The wind speed has dramatic effects on your Nature’s Wind Turbine. The
location shall be carefully considered to achieve the optimal performance of
your Nature’s Wind Turbine, prior to the mounting of your Nature’s Wind
Turbine. Each installation is unique and often a compromise among the
surrounding environment, the distance between your Nature’s Wind Turbine and
your Nature’s Generator, zoning requirements, budget and etc.
In general terms, the higher your Nature’s Wind Turbine can be mounted, the greater the airflow will be and thus the better power production will be. However, towers are expensive and can easily exceed the cost of the turbine. The minimum recommended tower height is 20ft to 30ft above nearby obstructions as shown below. The obstructions create turbulence which reduces the efficiency of the wind turbine may accelerate the wear and tear of your Nature’s Wind Turbine.
Safety must be the primary concern when selecting the mounting location. Install your Nature’s Wind Turbine so there is no possibility of accidental contact with rotating blades even if it requires installing the wind turbine in a less than ideal location. Safety has precedence over efficiency.
How to choose the tower
Your Nature’s Generator is designed to mount on nominal 1.5-inch schedule 40
steel tubing or piping. The outside diameter of the tubing or piping shall be
around 1.875 inches to 1.900 inches. The steel tubing or piping should be
available through your local hardware store. Under no circumstances should the
plastic pipes be used to construct a tower. Towers must be capable of
withstanding 160 pounds of load in the horizontal direction at the wind
turbine.
How to Install your Nature’s Wind Turbine
Caution: Choose a calm day and have someone available to help during the
installation process.
Caution: The blade’s edges are sharp. Please handle carefully.
Caution: Do not assemble the blades before the body is mounted on the pipe or
tower.
Caution: Do not connect your Nature’s Wind Turbine with Nature’s Generator
until all installation has been completed.
Step 1: Run the wind turbine cable through the pipe and drag the connector close to Nature’s Generator. The female connector shall be close to your Nature’s Wind Turbine and the male connector shall be close to your Nature’s Generator.
Step 2: Connect the wind turbine cable and your Nature’s Wind Turbine by pushing and twisting the connectors.
Step 3: The rubber gasket that is stored inside of the yaw and the included
rubber pad help to prevent the yaw from contacting the pipe directly. The
rubber gasket and rubber pad will assist in reducing the transmission of noise
and vibration down the pipe. Slide the yaw shaft all the way down over the top
of the pipe and be careful not to pinch the cable. There may be some slight
variances of the thickness or size of the pipe from different makers or
models. Please adjust the size of the rubber pad as needed.
Step 4: Firmly tighten the yaw clamp bolts with the 6mm hex key. Be sure that
your Nature’s Wind Turbine is securely attached to the pipe.
Step 5: Place one of the blades on
one of the hub sockets. Place a lock washer and then a flat washer on the bolt
and then insert the bolt through the blade ad the socket. Place a nut on the
other side of the socket and tighten the bolt with the 5mm hex key. Repeat
this process on all five blades. Make sure the lock washer and flat washer are
placed in the right order. The blades will become loose if it is not installed
properly.
Step 6: Slide the blade assembly onto the rotor shaft and place the lock washer and lock nut on the shaft.
Step 7: Insert the 8mm hex key into the rotor shaft. Hold the blade assembly and tighten the M16 nut by turning the 8mm hex key counterclockwise. If needed, please use the extender (not included) to extend the 8mm hex key to tighten the lock nut. Finally, spin the blades slowly to be sure they turn freely and the hub does move in along the rotor shaft.
Step 8: Place the nose cone over the centerline of the blade assembly and snap the nose cone into place.
Step 9: Carefully raise the tower and secure the base and/or cables.
How to connect your Nature’s Wind Turbine to your Nature’s Generator
Step 1: Connect the wind turbine cable to the round connector from one side of
the controller box by pushing and twisting the connectors
Step 2: Connector the square connector from the other side of the controller
box to your Nature’s Generator “WIND INPUT” port.
Step 3: When your Nature’s Wind Turbine spins at a certain speed, you will see
the whole display on your Nature’s Generator lights up if your Nature’s
Generator main power is switched off. It means your Nature’s Wind Turbine is
recognized by your Nature’s Generator, but it is not powerful yet to recharge
your Nature’s Generator. When your Nature’s Wind Turbine spins at the proper
speed, you will see the wind turbine icon on the display illuminates and the
battery bar starts running. It means your Nature’s Wind Turbine is recharging
your Nature’s Generator.
MAINTENANCE
Your Nature’s Wind Turbine has been designed to run for long periods without requiring any maintenance. The performance will be enhanced if you periodically inspect your system. Review the following simple maintenance procedures and implement them every six months.
Caution: Do not go near the wind turbine during operation.
- Check blades for superficial damage. Replace blades if damaged. It is important not to use blades that are damaged, as you will lose overall balance, resulting in a decrease inefficiency. Should you notice damage to the blades, you must replace all 5. The blades are balanced assets.
- Check the blade bolts and the nut for tightness.
- Check nose cone for cracks and tighten nuts.
- Wipe any excess dirt build-up from blades.
- Check electrical connections to make sure they are tight and free from corrosion.
Troubleshooting
Caution: You may require an extra person to assist with these tests.
- Remove the blade and hub from your Nature’s Wind Turbine.
- Drain your Nature’s Generator to show only one bar or two bars of battery level.
- Connect your Nature’s Wind Turbine to your Nature’s Generator. And make sure your Nature’s Generator main power is switched off.
- Set your power drill at speed mode and use an 8mm hex drive bit (not included, please purchase separately) to spin the rotor shaft.
- You will see the LCD display on your Nature’s Generator lights up and then your wind turbine icon illuminates and the battery bar starts running. It means your Nature’s Wind Turbine should be recharging your Nature’s Generator fine. You should also feel resistance on the rotor shaft.
If you have any questions on the troubleshooting procedures, please do not hesitate to contact our Customer Support line at 805-383-0003 or email us at support@naturesgenerator.com.
Technical Specifications
Material:
Wind turbine blades: fiberglass nylon composite
Wind turbine body: cast aluminum alloy with powder coating
Wind turbine cable: 12AWG pure copper cable
Connectors:
Wind turbine cable connectors: weatherproof M19 3P connectors.
Wind input connectors: Anderson connectors.
Yaw: fits 1.5 Inch schedule 40 pipes or towers
Power Rating:
Rated mechanical power: 400 watts @ 27 mph or 12 m/s wind speed
Rated electrical power: 150 watts
Maximum wind speed 110 mph
General:
Rotor diameter: 51 in / 1.3 m
Weight 22 lbs/10 kg not including cables and controller box.
Certifications: CE Rohs
Limited Warranty
One Year Limited Warranty
HuntKey USA Inc. warrants to you, the original purchaser of this new product,
that the product shall be free of defects in the original manufacture of the
material or workmanship for a period of one (1) year from the original date of
your purchase of the product (“Warranty Period”). This product must be
purchased from an authorized dealer and packaged with this warranty statement.
This warranty does not cover refurbished products.
What does this Warranty Cover?
During the Warranty Period, if the original manufacture of the material or
workmanship of the product is determined to be defective by an authorized
dealer, HuntKey USA Inc. will (at its sole option): (1) repair the product
with new or rebuilt parts; or (2) replace the product at no charge with new or
rebuilt comparable products or parts. Products and parts replaced under this
warranty become the property of Nature’s Generator and are not returned to
you. If service of products or parts are required after the Warranty Period
expires, you must pay all labor and parts charges. This warranty lasts as long
as you own your product during the Warranty Period. Warranty coverage
terminates if you sell or otherwise transfer the product.
How to Obtain Warranty Service?
Please call 1-805-383-0003 Monday
through Friday, 8:30 AM to 4:30 PM PST. You will be provided with a Return
Merchandise Authorization (RMA) number and return instructions. Send product
to:
Huntley USA, Inc.
735 W Ventura Blvd., Suite B
Camarillo, CA 93010
Please include the RMA number prominently displayed on the shipping box and include your name, phone number, and address with the product inside the box.
Where is the Warranty Valid? This warranty is valid only to the original
purchaser of the product in North America (the United States, Canada, and
Mexico).
Visit NaturesGenerator.com for More Information 16
What does the Warranty not cover?
This warranty does not cover:
- Cosmetic damage
- Damage due to acts of God, such as lightning strikes
- Accident
- Misuse
- Abuse
- Negligence
- Commercial use
- Modification of any part of the product
- Damage due to incorrect operation or maintenance
- Connection to an incorrect voltage supply
- Attempted repair by anyone other than a facility authorized by Huntkey USA Inc. to service the product
- products sold as is or with all faults
- Consumables, such as batteries
- Products where the factory-applied serial number has been altered or removed
REPAIR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS YOUR EXCLUSIVE REMEDY. HUNTKEY USA INC. SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR THE BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT, INCLUDING, BUT NOT LIMITED TO LOST DATA, LOSS OF USE OF YOUR PRODUCT, LOST BUSINESS, OR LOST PROFITS. HUNTKEY USA INC. PRODUCTS MAKES NO OTHER EXPRESS WARRANTIES WITH RESPECT TO THE PRODUCT, ALL EXPRESS AND IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF AND CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE AND NO WARRANTIES, WHETHER EXPRESS OR IMPLIED, WILL APPLY AFTER THE WARRANTY PERIOD. SOME STATES, PROVINCES, AND JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE.
Contact HuntKey USA Inc:
For customer service please call
1-805-383-0003
Huntley USA, Inc.
735 W Ventura Blvd., Suite B
Camarillo, CA 93010
Visit NaturesGenerator.com for More
Information
References
- Solar Generator & Wind, Whole Home Power Backup | Nature's Generator
- Solar Generator & Wind, Whole Home Power Backup | Nature's Generator
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>