LUTEC 6222W LED Flood Light Owner’s Manual

LUTEC 6222W LED Flood Light

Product Information

LED Floodlight

• Model: #6222W/6222B

Specifications

• Package Contents:
  • Fixture: 1
• Hardware Contents:
  • Screw Qty. 2
  • Wire Nut Qty. 3
  • Mounting Plate Qty. 1
  • Rubber Plug Qty. 1
  • Foam Pad Qty. 1
• Estimated Assembly Time: 20-30 minutes
• Tools Required for Assembly: Phillips Screwdriver, Silicone Caulking Adhesive, Ladder
• Warranty: 3-Year Limited Warranty

Product Usage Instructions

Safety Information

• Please read and understand this entire manual before attempting to assemble, operate, or install the product.
• WARNING: Before beginning assembly or installation, ensure that all parts are present and undamaged. If any part is missing or damaged, do not proceed with assembly, installation, or operation.

Preparation
Before starting the assembly process, make sure you have all the necessary parts. Compare the parts with the package contents list and hardware contents list provided in the manual. If any part is missing or damaged, do not proceed.

Installation

1. Turn OFF power to the work area at the main circuit breaker or fuse box. Do not rely on the wall switch alone to turn off power.
2. Remove the screw pre-assembled in the mounting plate (CC) and set it aside for later use.
3. Attach the mounting plate to the junction box (not included)  using the two screws (AA).
4. Attach the foam pad (EE) to the mounting plate.
5. Connect the ground wire from the junction box to the ground screw on the mounting plate. Then connect the ground wire from the junction box to the ground wire from the fixture (A) by twisting a  wire nut (BB) onto the bare ends of the wires.
6. Connect the white wire from the junction box to the white wire from the light fixture by twisting a wire nut (BB) onto the bare ends of the wires. Connect the black wire from the junction box to the black wire from the light fixture by twisting a wire nut (BB) onto the bare ends of the wires. Position all the wires inside the fixture junction box.
7. Attach the light fixture (A) to the mounting plate using the screw previously removed in step 2. Insert the rubber plug  (DD).
8. After mounting the fixture, apply silicone caulking compound completely around the perimeter of the cover plate where the back of the cover plate meets the mounting surface. This prevents water from seeping into the junction box.
9. Turn ON power to the work area at the main circuit breaker or fuse box.

Care and Maintenance

To ensure proper functioning and longevity of your LED  floodlight, follow these care and maintenance guidelines:

• Regularly clean the surface of the fixture using a soft cloth and mild detergent.
• Inspect the fixture for any signs of damage or wear. If any issues are detected, contact customer support for assistance.

Troubleshooting

If you encounter any issues with your LED floodlight, refer to  the following troubleshooting guide:

3. The switch may
   be wired incorrectly. Crossed wires or power wire is grounded
   out.| 1. Make sure the lamp fixture is plugged in and power is on. 2.
   Check wiring. 3. Check wiring. Consult a certified electrician if
   needed.
   Fuse blows or circuit trips when the fixture is turned on.| 1. No power. 2. Fixture may be wired incorrectly. 3. The switch may
   be wired incorrectly. Crossed wires or power wire is grounded
   out.| 1. Make sure the lamp fixture is plugged in and power is on. 2.
   Check wiring. 3. Check wiring. Consult a certified electrician if
   needed.

Warranty

This LED floodlight comes with a 3-year limited warranty. If the product fails due to a defect in materials or workmanship within three (3) years from the date of purchase, it will be replaced with the same or a comparable model free of charge. This warranty is  void if damage or defect results from accident, abuse, misuse, or faulty repair. Please retain proof of purchase.

FAQ

• Q: Can this fixture be installed on the ceiling?
  A: Yes, this fixture can also be installed on the ceiling.

IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY

PACKAGE CONTENTS

HARDWARE CONTENTS

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install the product.

• Consult a qualified electrician if you are not certain about the installation process. Always install wiring connections in accordance with local code, ordinances and the National Electric Code.
• Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
• This light fixture is designed to fit standard junction boxes as defined by the National Electrical Code.
• This light fixture is not dimmable.

This Class B digital apparatus complies with Canadian ICES-005.
NOTICE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

PREPARATION

• Before beginning to assemble or install lighting fixtures, make sure all parts are present. Compare parts with the package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble, install or operate the product.
• Estimated Assembly Time: 20-30 minutes.
• Tools Required for Assembly: Phillips Screwdriver, Silicone Caulking Adhesive, Ladder

INSTALLATION

1. Turn OFF power to work area at the main circuit breaker or fuse box.
   CAUTION : Do not rely on wall switch alone to turn off power.

2. Remove the screw pre-assembled in the mounting plate (CC). Put the screw a side  as they will be used later.

3. Attach the mounting plate to the junction  box (not included) using the two screws (AA).
   Then attach the foam pad (EE) to the mounting plate.
   This fixture can also be installed on the ceiling

4. Connect the ground wire from the junction box to the ground screw on the mounting plate. Then connect the ground wire from the junction box to the ground wire from the fixture (A) by twisting a wire nut (BB) onto the bare ends of  the wires.
   Connect the white wire from the junction box to the white wire from the light fixture by twisting a wire nut (BB) onto the bare ends of the wires. Connect the black wire from the junction box to the black wire from the light fixture by twisting a wire nut (BB) onto the bare ends of the wires. Position all the wires inside the fixture junction box.

5. Attach the light fixture (A) to the mounting plate using the screw previously removed  in step 2. Then insert the rubber plug (DD).

6. After mounting the fixture, apply silicone caulking compound completely around the perimeter of the cover plate where the back of the cover plate meets the mounting surface. Silicone caulking prevents water from seeping into the junction box.

7. Turn ON power to work area at main circuit breaker or fuse box.

CARE AND MAINTENANCE

Clean surfaces with a mild, non-abrasive cleaner

TROUBLESHOOTING

2.        Fixture may be wired incorrectly.

3. The switch may be wired

incorrectly.

| 1.     Make sure the lamp fixture is plugged in and the power is on.

2.     Check wiring.

3.     Check wiring.

Fuse blows or circuit trips when fixture is turned on.| Crossed wires or power wire is grounded out.| Consult a certified electrician.

WARRANTY

3-YEAR LIMITED WARRANTY

• If this product fails due to a defect in materials or workmanship within three (3) years from the date  of purchase, return it along with proof of date of purchase and it will be replaced with the same or comparable model free of charge.
• This warranty is void if damage or defect has resulted from accident, abuse, misuse or faulty repair.
• This warranty gives you specific legal rights and you may have other rights that vary from state to state.
• IN NO EVENT WILL LIABILITY EXTEND TO ANY CONSEQUENTIAL, SPECIAL, INCIDENTAL OR INDIRECT DAMAGES OF ANY KIND ARISING OUT OF THE USE OR MISUSE OF THIS PRODUCT. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU.

LUTEC USA LLC:
149B Houston Rd Troutman NC 28166 Ningbo UTEC Electric Co.,LTD CN8, Far East Industry Park, Yuyao, China
www.lutec.com
service@lutec.com
Please call our Customer Service line at 877-714-8669  for assistance Monday – Friday 9 a.m. to 5 p.m. EST
Printed in China

References

• Home | Lutec

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>