SOMiC MS500 Wireless Noise Cancelling Headphones User Manual

SOMiC MS500 Wireless Noise Cancelling Headphones
User Manual

Button/Port function introduction:

charging port: earphone charging port
 3. Volume” button: lower the volume of earphones to the previous song|  7. Charging status indicator window: low power reminder, display charging status
 4.@Working indicator: displays the working status of earphones|  8.@ANC Button: three noise reduction mode switching button

Basic Operation Instructions

1. Power and Pairing:
   Press the long button for 3 seconds to start up, and the earphone will sound “Power on”After Startup, If no historical match is recorded, the match mode is entered, At the same time, the headset plays a “pairing” tone or A connected” tone is played when the connection is successful. After the startup, if there is a historical matching record, it enters the connection back mode.

2. Power off: (The headset will have a sound reminder” Power off” when turned off) Wireless mode: Long press the multi-function button for 3 seconds,the headphone will turn off with the sound prompt “Power off” when during the Power on the state.  The headphone will turn off if they can’t connect to any device when pairing. During the power-on state, the headset will turn off when insert Type C for charging. During the power-on state, the headset will turn off when inserting a 3.5mm Aux cord, At the meantime, the headset will play the signal of the external device The pairing lasts for 3 minutes, if the pairing fails, it shuts down immediately.

3. Reconnect mode
   The headset will enter connect back mode in the following situations: When turned on, the headset and the mobile phone have a historical matching record; During usage, the headset is abnormally disconnected (excluding disconnec­ notion of the mobile phone via manual handling)The re-connection lasts for 30 seconds. If the connection is successful, it will end early. If the re-connec­ tion fails, it will enter pairing mode.

4. Pairing mode
   The headset will enter Pairing mode in the following situations:  When powered on, there is no historical matching record between the headset and the device. When the re-connection mode fails. When the mobile phone manually disconnects the current device. Press and hold the volume “+” key and the volume”-” key for 3 seconds at the same time to clear the pairing record Allows any device to actively connect when in pairing mode; The pairing lasts for 3 minutes, and the connection ends early if the connection is successful. If the pairing fails, it will be shut down directly.

5. Clear pairing
   Press the volume “+” key and the volume “-” key for 3 seconds to clear the pairing record.

6. Noise reduction mode
   Press the ANC button to switch the noise reduction mode, which can be divided into deep noise reduction mode, shallow noise reduction mode, and transparent mode. When in deep noise reduction mode, the hint sound is ANC High, when in shallow noise reduction mode, the hint sound is: ANC Low, when in transparent mode, the hint sound is: Transparent Mode.

7. music play/pause
   when playing music, click the multi-function key to pause/play music.

8. Volume control
   To increase the volume, click the + key (the volume adjustment range is synchronized with the external device). To reduce the volume, click the -key (the volume adjustment range is synchronized with the external device).

9. Switch songs
   Next song: Long press the volume “+” button for 2 seconds; Previous song: Long press the volume”.” button for 2 seconds.

10. Call Mode
    To answer an incoming call, click the multi-function button When an incoming call comes in, double-click the multi-function button to reject the call During a call, click the multi-function button to end the call When an incoming call comes in, the music automatically pauses and the headphone ring tone is played. When you reject or end a call, the music playback automatically resumes.

11. Voice Assistant
    When the device is connected, triple-click the multi-function button to trigger the mobile phone voice assistant. When the voice assistant is triggered, click the multi-function key to exit the MOBILE phone voice assistant.

12. Low power:
    When the device is in use, there will be a hint sound if the working time is less than 15 minutes; When the device is turned on, the power of the headset is 15 minutes of normal working time, it will remind once; When the device is turned off, the power of the headset is less than or equal to 15 minutes of normal working time, it will remind once; When the battery is exhausted, it will automatically turn off after reminded.

13. Charging Mode:
    Insert the headset charging cable to connect the power supply and enter charging mode; When charging, the power indicator light is orange; When charging is complete, the power indicator light is green;

14. Wired Mode:
    Contact with 3.5mm audio cable; In this mode, the headset only retains the speaker playback function, and the microphone cannot pick up sound and the button function cannot be used.

Tip:

1. Please read the instructions carefully before using the product and keep them properly;
2. Please charge the product before using it for the first time; If the product is not used for a long time (more than 2 weeks), please charge it;
3. Choose the Chargers which produced by regular manufacturers and certified by the national CCC;
4. If the phone cannot receive the Bluetooth headset, please confirm whether the Bluetooth headset is in “pairing mode”. If the phone has not been paired or connected for a long time

Basic Operation Instruction

To avoid wasting your valuable time, pls check the following before sending repairs.

time.
Unable to Paring| The phone has not yet enabled the Bluetooth function or has not yet opened the discoverable status.| Start Bluetooth and set it to discoverable.
When paired, the headphones are too far from the ransmitter.| Please do not distance to more than 1 meter.
The battery power is insufficient.| Charge the battery in time.
The noise is large| The battery power is insufficient.| Charge the battery in time.
Staccato| 1. The headset is too far from the transmitter, beyond the
receiving range.
2. There is an obstacle between the headphones from the transmitter.| Resweak properly to listen.
The receiving distance is short| 1. Transmitter equipment compatibility issues.
2. There is an obstacle between the headphones from the transmitter.| 1. Replace the transmitting equipment
2. Reset the appropriate location to listen

FCC Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Product Features

1. A headset is available in three connectivity modes (normal Bluetooth mode, Bluetooth low latency mode (with a transmitter), and 3.5mm wired mode) for a variety of scenarios and devices.
2. The headset has two sound modes of game and music, both listening to songs and games. Thanks to 35ms super low latency, you can enjoy the game experience of audio and video synchronization.
3. A headphone microphone is a retractable microphone that can be adjusted according to the usage scenarios.
4. A headset is a built-in 1000mA capacity battery with super long life and up to 50
5. Headsets are ergonomically designed tough appearance and domineering appearance.
6. Headphones feature large skin-stick leather carcasses for comfortable wear.

Note

1. This product is compatible with Microsoft Windows 7/8/10, Apple Mac OS system, Android system, and IOS system;
2. 4fit is not available on the operating system or equipment that is not listed, you can contact the after-sales service for a solution;
3. During the use of the product, if there is no sound from the microphone or headset, it may be caused by compatibility problems or improper use, and you can contact the after-sales service to find a solution;
4. During the use of the product, if any part is damaged, such as a broken cable, please stop using it and contact the after-sales service for a solution to avoid unnecessary losses.
5. During the use of the product, if the headset does not respond for a long time, you can use a sharp object such as a paper clip to press the headset reset button for 1 second, and the headset can be forced to shut down.
6. If you want to know more information, please visit Somic’s official website www.itsomic.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>