PROLED L6OP7SRCxxxxx Opal Saber Pendant Lamp Instruction Manual
- July 8, 2024
- PROLED
Table of Contents
PROLED L6OP7SRCxxxxx Opal Saber Pendant Lamp
Product Information
Specifications:
- Product Name: SABER SUSPENSION RC
- Manufacturer: MBN GmbH
- Input Voltage: 220-240VAC
- Energy Efficiency Class: F
- For indoor use only
- Protection Class: IP20
Product Usage Instructions
Installation:
Please follow the sequence of installation step by step to avoid damaging the
LED:
- Switch off the electricity at the mains before commencing installation or lamp change. Remove the appropriate circuit fuse if available.
- Connect the light to a power supply (secondary side) or a dimmer.
- Connect the primary side of the driver to the power supply (230VAC).
- Ensure all connections are tight with no loose strands.
- Make sure not to breach fire regulations while fitting the lights.
- If in doubt, consult a qualified electrician.
FAQ
Q: Can I use this product outdoors?
A: No, this product is designed for indoor use only.
Q: What should I do if the cable is defective?
A: Do not use the luminaire if the cable is defective. Contact a qualified electrician for repair or replacement.
Q: What should I do if I accidentally look at the lighted lamp directly?
A: Avoid looking directly at the lighted lamp to prevent eye strain. If accidental exposure occurs, look away and rest your eyes.
Characteristics
- OPAL SABRE Super Warm White, Warm White, Neutral White, or RGB
- Power consumption 15 – 18,5 W/m
- Metall housing round
- Mounting ring colour White, Black, or Gold
- Suspension rope 0-100 cm
- Power supply 24 VDC
- Dimmable with a complying PWM dimmer and controller
- Operating temperature range -10° C till +45° C
- CE compliant with applicable European directives
Warning:
- For indoor use only
- Please ensure that the packaging is disposed of in a safe environment
- If the cable is defective, do not use luminaire
- We do recommend that a qualified electrician should be used to install the products
- Do not look at the lighted lamp directly
Safety indices
Be sure to have a qualified electrician complete the installation. The customer is not entitled to claim for any lights installed without observing European safety directives. The manufacturer is then discharged from liability when damage is caused by improper use or installation. If any luminaire is subsequently modified, the person responsible for the modification shall be considered as manufacturer. Do not cover lamps with heat-insulating materials. For indoor use only. Protection class IP20.
Installation
Please follow the sequence of installation step by step. Non-observance can lead to damage to the LED.
- Switch off the electricity at the mains before commencing installation or lamp change and (if a fuse box is installed) remove the appropriate circuit fuse to avoid accidental switching on of the mains supply.
- Connect the light to a power supply (secondary side) or a dimmer
- Connect the primary side of the driver to the power supply (230VAC)
- Make sure all connections are tight with no loose strands
- Ensure fire regulations are not breached when fitting your lights
- If you are in any doubt regarding these instructions, consult a qualified electrician
Please follow the sequence, if not destroying of LED:
Remark to the energy efficiency class of the light source:
This product contains a light source of energy efficiency class F:
Attention:
- This product counts as a„ containing product“ according to directive (EU) 2019/2020 and (EU) 2019/2015.
- The light source is part of the containing product. A separation of the light source and the containing product using commonly available tools is possible with this product.
- Replacement of the light source using commonly available tools is possible with this product.
- The light source can be separated for testing purposes.
- Installation and commissioning may only be performed by qualified persons.
- National installation regulations must be observed.
- Luminaires must be disconnected from the mains before any work.
MBN GmbH, Balthasar-Schaller-Str. 3, 86316 Friedberg – Germany www.proled.com.