Zip WATER BCS Celsius Plus All-In-One Zip HydroTap Instruction Manual
- June 13, 2024
- Zip WATER
Table of Contents
- BCS Celsius Plus All-In-One Zip Hydro Tap
- Positioning
- Cut the hole
- Familiarise yourself with the mains connections
- Familiarise yourself with the tap connections
- Mount and secure the tap
- Connect the water supply
- Be careful with the sparkling pipework
- Command Centre connections
- Cleaning and general maintenance
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Installation instructions
Zip Hydro Tap
Celsius Plus All-In-One
BC, BCS
BCS Celsius Plus All-In-One Zip Hydro Tap
Visit our website to download the manuals
|
---|---
Using these instructions
Please refer to all safety and installation requirements detailed in the Quick
start guide provided with the HydroTap Command Centre, and HydroTap Command
Centre installation instructions found online, prior to installation of, or
any change to, the complete system.
Before commencing the installation, download & read the Hydro Tap Command Centre installation instructions
Tools needed for installation (not supplied)
In addition to normal tools, the following (or equivalent equipment) will be
required.
- 50mm diameter sheet metal hole punch for sinks.
- 50mm diameter hole saw for worktops.
- Tube spanner for fixing the tap assembly.
Be aware of the risks of hazards which could cause harm when using tools. Assess the risks before starting the installation.
Water supply pressure requirements
| Min – Max pressure, kPA (bar)
---|---
| Australia| UK
HydroTap| 170 (1.7) – 700 (7.0)| 170 (1.7) – 500 (5.0)
Sparkling
HydroTap| 250 (2.5 ) – 700 (7.0)| 250 (2.5) – 500 (5.0)
Booster| 200 (2.0) – 700 (7.0)| 200 (2.0) – 500 (5.0)
Positioning
Position the tap such that it dispenses into the sink bowl with clearance for a cup or tea pot.
Ensure that taps are positioned to minimise the risks of scalding by dispensing boiling water while using the tap.
Position Command Centre and Tap as close together as possible.
Cut the hole
- Cut a Ø50mm hole in the worktop / sink.
- Make sure the tap location will allow the tap spout to drain into the sink.
Familiarise yourself with the mains connections
Familiarise yourself with the tap connections
Mount and secure the tap
Connect the water supply
All fittings are supplied apart from the isolation valve.
Valves and fittings must be sealed with PTFE tape.
Be careful with the sparkling pipework
- Silicone tubes are soft and easily deformed. It is essential to avoid kinks, loops and sags.
- Loosely cable-tie the rigid sparkling pipework to an adjacent braided hose to avoid kinks and squeezing.
Command Centre connections
| Mains In | Mains potable water supply. |
|---|---|
| USB | Connected the Tap. |
| Boiling out | Red silicone tube from tap. Cut to length. |
| Chilled out | (BCS) Blue JG pipe from tap. Cut to length. |
(BC) Blue silicone tube from tap. Cut to length.
Vent| Clear silicone tube from tap. Cut to length.
Sparkling out| White JG pipe from tap. Cut to length.
Cleaning and general maintenance
Wipe surfaces with a damp cloth and then wipe dry with a clean, dry cloth. Do not use disinfectant sprays without wiping dry afterwards.
Water Mark
WMK25927
AS/NZS 3718
Zip Water
67 – 77 Allingham Street, Condell Park, NSW 2200
Postal: Locked Bag 80, Bankstown 1885, Australia
(+612) 9796 3100 | Free Call (Aust): 1800 947 827
www.zipwater.com
Zip Water UK
Trafalgar House
Rash’s Green, Dereham,
Norfolk NR19 1JG
0345 6 005 005
specify.zipwater.co.uk
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>