FORTIN RM942 Remote Starters and Alarm Systems User Guide
- June 5, 2024
- FORTIN
Table of Contents
FORTIN RM942 Remote Starters and Alarm Systems
Product Information
Specifications:
- Product Name: RM942
- Remote Type: 2-Ways Remote
- Model Number: FRM942-2W
- Remote FCC ID: 2ACKU-RM942/IC: 12084A-RM942
- Antenna FCC ID: 2ACKU-ANT900/IC: 12084A-ANT900
Product Usage Instructions
-
Locking and Unlocking:
- To lock the vehicle, press the LOCK button for 0.5 seconds. This action locks all doors, arms the anti-theft system, and activates the alarm system if available. A single beep and a green flash will confirm the action.
- To unlock the vehicle, press the UNLOCK button for 0.5 seconds. This action unlocks all doors, disarms the anti-theft system, and deactivates the alarm system if available.
-
Remote Start:
To remote start the vehicle, press the START button for 3 seconds. The remote start will be initiated, and the engine will run for the selected runtime (default settings apply). -
Opening Trunk:
To open the trunk, press the TRUNK button for 3 seconds. The trunk will open, and the alarm system will be deactivated in that zone until it is closed. -
Auxiliary Functions:
The remote also features auxiliary functions. Press AUXILIARY1 or AUXILIARY2 for 0.5 seconds to activate these features if available. -
Disabling/Enabling Buttons:
To disable all buttons on the remote for safety purposes, simultaneously press all buttons for 3 seconds until the red LED turns on. To enable them back, follow the instructions provided in the manual.
FAQ:
Q: What should I do if my remote’s buttons are disabled?
A: If the remote’s buttons are disabled, it may indicate weak batteries that
need replacing. Ensure to replace them with new batteries to enable the
buttons again.
BUTTON DESCRIPTION
REMOTE STARTING
When leaving the vehicle it is recommended that the driver pre-set the climate controls in preparation for a later remote start. To remote start the vehicle:
-
STEP 1
To remote-start the vehicle press the START button for approximately 3 seconds The remote Green Led flash and an ascending melodie will sound to confirm. -
STEP 2
Approximately 5 seconds later the engine will crank and run for the selected runtime (15 minutes by default).
If the vehicle fails to start on the first attempt, the Remote-Starter will wait 3 seconds before it will attempt to start the vehicle again. The Remote- Starter will attempt to start the vehicle 2 times (default) before giving up. (See Failed Remote Start, on the complete user guide).
RUNTIME:
On gas engines, the Remote-Starter can run the vehicle for either 15
(default), 3 or 7 minutes. On diesel engines either 30 (default), 6, or 15
minutes.
REMOTE STARTING FROM FACTORY KEY FOB
IF OPTION AVAILABLE. To remote start the vehicle with the factory key fob:
- PRESS LOCK 3 TIMES (By default) or PRESS LOCK UNLOCK LOCK.
- Remote-start the vehicle.
SERVICING THE VEHICLE
WHEN SERVICING THE VEHICLE
Valet Mode disables the remote starter and alarm. Whenever the vehicle is
being serviced, or repaired or the vehicle is parked indoors; it is mandatory
that Valet Mode be enabled to prevent an accidental remote start.
FROM THE ANTENNA
-
STEP 1
Turn the vehicle ignition to (ON/RUN) position. The vehicle does not need to be started. -
STEP 2
Within 10 seconds press and release the button on the antenna 3 times.
FROM THE REMOTE
- Press and release the FUNCTION button, and then press simultaneously the LOCK and UNLOCK.
- VALET MODE ENABLED: The LED is ON
- VALET MODE DISABLED: The LED is OFF
KEY TAKEOVER AFTER REMOTE STARTING
**KEY TAKEOVER FOR STANDARD KEY VEHICLE***
-
STEP 1
Do not press the foot brake (the engine will shut down). -
STEP 2
Insert the key into the ignition and turn to the ON position. -
STEP 3
Press the foot brake.
**KEY TAKEOVER FOR PUSH-TO-START VEHICLE***
-
STEP 1
UNLOCK the doors with either the OEM remote, the remote-starter remote or the proximity remote.
FORD/HYUNDAI/INFINITI/KIA/MAZDA/NISSAN/SUBARU -
STEP 2
Enter the vehicle with the SMART-KEY. -
STEP 3
Do not press the foot brake. -
STEP 4
Press and release the Push-to-Start button once. -
STEP 5
Press the foot brake. -
STEP 6
The vehicle can now be put into gear and driven. If the Smart-Key is not detected the vehicle will shut down.
**ACURA/HONDA/LEXUS/SCION TOYOTA ***
-
STEP 1
The module will shut down the vehicle as soon as the drivers door is opened. -
STEP 2
Press the foot brake. -
STEP 3
The vehicle can now be put into gear and driven.
The remote starter key takeover may vary by vehicle, ask your adviser or technician for details.
**REMOTE START DIAGNOSTICS***
Parking Light flashes (before starting):
- 3x Ready mode disabled
- 4x Valet mode activated (The LED is on)
- 5x Hood open
Parking Light flashes (after Shutdown):
- 1x Normal stop (Brake, Park Brake)
- 3x Runtime expired or shut down by transmitter
- 4x No tachometer signal
- 5x Hood open
- 6x Fail to start
**ALARM DIAGNOSTICS***
Parking Light flashes (after disarm):
- 3x Door open – zone 3
- 4x Shock sensor – zone 4
- 5x Hood open – zone 5
- 6x Trunk open – zone 6
The parking light diagnostics can not be used on some vehicles equipped with automatic lights.
RANGE
Up to 2 KM/6500Ft range
BATTERY
- BATTERY REQUIRED: 2x CR2016
- AVERAGE BATTERY LIFE: 24 months
THANK YOU FOR PURCHASING THIS REMOTE-STARTER/ALARM SYSTEM. WE RECOMMEND THAT YOU DOWNLOAD AND THOROUGHLY REVIEW THE COMPLETE USER MANUAL FOR MORE INFORMATION ABOUT THE REMOTE STARTER/ALARM SYSTEM AT: evoremotestart.com/rm942.
CAUTION AND WARNING
IT IS THE RESPONSIBILITY OF THE REMOTE CAR STARTER OPERATOR TO:
- ensure that the vehicle is parked safely and responsibly.
- ensure that the vehicle is not remotely started indoors (garage, underground parking).
- ensure that the vehicle is not remotely started with a passenger inside.
- ensure that the vehicle is not remotely started with a window or the roof open.
- ensure that the gearshift lever is in the NEUTRAL position and the parking brake is engaged on manual transmission to avoid accidents upon remote starting.
- when leaving the vehicle, ensure that the gearshift lever is in the “PARK” position for automatic transmission to avoid accidents upon remote starting. Make sure that the vehicle cannot start in the “Drive” position.
- ensure that the remote starter is disabled or put into valet mode before servicing. When servicing the vehicle, download the complete user guide for more information.