JONATHAN Y JYL6313 Hanging Light Lighting Antler Chandelier Instruction Manual
- June 1, 2024
- JONATHAN Y
Table of Contents
JONATHAN Y JYL6313 Hanging Light Lighting Antler Chandelier
INTRODUCTION
Item Number: JYL6313
WARNING (To reduce the risk of fire, electric shock, or injury to persons):
- We suggest installation by a licensed electrician.
- Please read the instructions carefully and save them as you may need them at a later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF” position.
- The mounting surface should be clean, dry, flat, strong enough, and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before the fixture.
- Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb. Please use Type “B” Bulb max 40-watt CFL Bulb max 13-watt or LED Bulb max 9-watt there is an LED 3pcs 4-watt Bulb in the Box.
- Keep the lamp away from acidic and basic objects in case of damaging the surface of the lamp.
- When replacing the bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution, and care must be used with any electrical products.
If there are any questions relating to defects, missing parts, assembly issues, replacements, or device connectivity issues, please send a detailed email to cs@jonathany.com
TOOLS REQUIRED (NOT INCLUDED)
Before doing assembly and installation please prepare the needed tools as below picture
PARTS TYPE & QTY INCLUDING
- (A) Plastic wire connector (3)
- (B) Hex nut (2)
- (C) Green ground screw (1)
- (D) Mounting plate (1)
- (E) Mounting screw (2)
- (F) Threaded nipple (1)
- (G)Canopy (1)
- (H) Screw collar loop (1)
- (I) Quick link (2)
- (J) Threaded ring (1)
- (K) Chain (1)
- (L) Loop (1)
- (M) Antler chandelier main body (1)
- (N) Bulb (3)
ASSEMBLY & INSTALLATION INSTRUCTIONS:
- Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration
- Make assembly
If the group of parts are not already assembled:
- Step A1 :Fix the threaded nipple(F) into the screw collar loop(H)
- Step A2 :Thread the mounting plate(D) over the another end of threaded nipple(F) ,
- Step A3 :Place and tighten the hex nut(B) to secure the mounting plate(D) in place. At this point, the side of the mounting plate marked “GND” must face the screw collar loop(H).
Make pre‐installation
- Step B1: Open the quick links (I) to connect the loops (L) on the antler chandelier main body(M), and to connect the loop(L) Close the quick links(I)
- Step C1 : By measuring, determine the correct length of links needed. Use the chain pliers, and open and discard the remaining chain.
- Step C2 : Attach a quick link(I) to the loop(L) above the antler chandelier main body(M) and connect the end of the chain(K).
- Step C3 : Gently lace wires through chain(K) to the top of another quick link(I) and pull still-sung
- Step C1: Attach Mounting plate(D) to the outlet box with mounting screws(E). The side of single bar marked “GND” must face out
- Step C2 : Raise the canopy(G) through the screw collar loop(H) and screw the collar loop(J) to a proper position by measuring. Unscrew the threaded ring(J) from the screw collar loop(J) and remove the canopy(G).In this way, you would know the proper position on which collar loop it should be located.
- Step C3 : Slip threaded ring(J) over the chain(K), then do the same with the canopy(G)
- Step C4 : Open the quick link(I) then attach it to the collar loop(H). Close the quick link(I) Pass the wires through collar loop(H) to the mounting plate, and gently pull the still-sung
- Step C5 : Make wire connections Connect wires as below wires connecting shown. TAKE NOTE OF THE COLOR OF THE FIXTURE, NEVER
CONNECT WIRES TO GROUND WIRES
Connect ground wire according to the below chart Connect ground wire according
to the below chart
Turn off power
Make installation
Twist plastic wire connector(A) until wires are tightly joined together, wrap each connector with approved electrical tape for a more secure connection, and carefully stuff all wires into the outlet box
- Step C6: Raise canopy(G) to ceiling and secure canopy(G) in place by tightening threaded ring(J) onto screw collar loop(H)
- Step C7 : Install bulb (N) (Please do not exceed the maximum capacity recommended on the socket.)
Check everything is already installed properly, then you can turn on the light.
CLEANING
To clean, wipe the fixture with a soft cloth, Do not use abrasive materials
such as scouring pads or powders, steel wool, or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. All parts for this fixture can be ordered from the place of
purchase. Be sure to use exact wording from illustrations when ordering parts.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>