AGPTEK APT829G Wireless In Car Speakerphone User Manual

AGPTEK APT829G Wireless In Car Speakerphone

Function Button Introduction

Operation

Charging
Please make sure that the device is fully charged for the first time, which takes about 2 hours.

Important Tips

1. If the device has not been used for a long time or the battery is out of power, there will be a short delay in the charging indicator light.
2. During the charging process, the LED is solid red, and the LED is powered off when fully charged.

ON/OFF
Push the button to turn on the speakerphone, and the device is automatically connected to the previously paired mobile phone.

Auto ON/OFF

1. The car speakerphone will automatically turn off after being disconnected from the mobile phone for 10 minutes. 3.2 Every time you get in your car, tap the device or open/close the door, the car speakerphone will automatically turn on using its built-in motion sensor and being connected to the paired mobile phone.

Pair with Phone 1

The device can be connected to 2 mobile phones with Bluetooth function at the same time. If you only pair with 1 mobile phone, the steps are as follows:

1. Place this device and mobile phone within 1 meter of each other
2. After powering on, you can hear the voice prompt and enter pairing mode.
3. Activate the Bluetooth function of the mobile phone to search for the pairing name of Bluetooth devices.
4. Select the pairing name of Bluetooth in-car speakerphone in your mobile phone, and click to pair (some mobile phones require the pairing password “0000” when pairing). After successfully paired, you will hear the audible tone.

Note: If the device is not paired successfully within 2 minutes, please turn it off and follow the above method again.

Pair with Phone 2

1. Turn off Phone 1 ‘s Bluetooth to disconnect with Bluetooth In-car Speakerphone
2. Turn off the device and then turn it on again.
3. Repeat all the steps mentioned in Section 4 “Pair with Phone 1”.

Instructions after Connecting

1. Answer/Reject call When a call comes in, click to answer the call. And a short press to hang up the call.
2. Reject call When there is an incoming call, you can double-click to reject the call.
3. Redial last dialed phone number Double-click to call the last dialed phone number.
4. Switch to answer privately During a call, you can press and hold  for 3s to switch to answer privately.

Mute
When playing music or making a call, click the “Mute button” to turn off the voice.

Volume control
Rotate the knob on the speaker to decrease or increase the volume.

Music Playback
After connecting with your Bluetooth-enabled devices, you can play the music via Bluetooth in-car speakerphone. This device supports playing MP3/WMA audio files on the TF card, and when the TF is inserted, the audio files on the TF card will be played first. When playing the music, short press M button to switch to the next song, double-click the M button to switch to the previous song, long press the M button to switch between TF card and Bluetooth, and short press the to pause.

Note: While playing music, it will automatically switch to Bluetooth hands-free calling mode when a call comes in. After the call ends, it automatically returns to music playback mode.

Activate Siri and Google Assistant
After this device is connected to the mobile phone, press and hold for 3s, and will hear the prompt, for successfully activating Siri and Google Assistant functions (make sure the phone supports the above functions).

Self-protection with low power
When the battery power is too low, it cannot work properly and will automatically turn on and off repeatedly. At this time, please charge it in time to ensure that can work properly.

Specifications

• Bluetooth Standard V5.3+BR+EDR
• Bluetooth Frequency ISM 2.4GHz-2.48GHz
• Bluetooth Operating Range 0-10m
• Charging DCSV , 300MA
• Built-in Rechargeable Battery 3.711, B00mAh
• Normal Charging Time 2H

Precautions & Daily Maintenance

1. Keep the device away from liquids, humid environments, or extreme high or low temperatures.
2. Do not wipe or clean with corrosive liquids.
3. Keep the device away from any sharp object to avoid scratches or damage.
4. Do not disassemble the device, or may damage the internal components.
5. Keep the device in a dry environment when not in use.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>