HOOKE ROAD BXG.9805-S Front Bumper Installation Guide

HOOKE ROAD BXG.9805-S Front Bumper

Product Information

Specifications :

• Model: BXG.9805-S
• Parts Included:
  • 4 x Hex Bolts (M10*35)
  • 15 x Button Head Socket Cap Bolts Screws (M8*20)
  • 2 x Button Head Socket Cap Bolts Screws (M6*16)
  • 4 x Split Lock Washer (M10)
  • 15 x Flat Washer (M8201.5)
  • 2 x Flat Washer (M6161)
  • 4 x Flat Washer (M10252)
  • 8 x Flange Hex Lock Nuts (M8)
  • 2 x Flange Hex Lock Nuts (M6)

Tools Required:

• Drive Socket Ratchet Wrench
• 10mm, 13mm, 14mm Wrench
• 10mm, 13mm, 14mm Shallow Socket
• 4mm, 5mm Hex Bit Socket
• Masking Tape
• Cutting Machine

Installation Time:

About 1.5 hours, 2-3 people may be needed. Installation time may differ according to your mechanical skill level.

Installation Instructions:

1. 1.  **Cutting The Factory Bumper:**

   1. Step 1: Ready to cut the factory bumper. It is strongly recommended to find a professional for cutting operations.
   2. Step 2: Take safety precautions: Ensure the vehicle is parked in a safe location and wear appropriate safety goggles and gloves during the cutting process.
   3. Step 3: Positioning and marking. Identify and mark the areas on your vehicle’s front bumper that require cutting.
   4. Step 4: Cut the bumper: Carefully cut the bumper using the chosen tool, following the marked positions.
   5. Finishing and refinement: After completing the cut, clean up any debris and refine the cut edges to achieve a neat and smooth appearance.

FAQ

• Q: Do all the parts in the instructions need to be exactly as described?
  • A: The product parts in this instruction may differ slightly from the actual product contents but generally do not affect the installation of the product.
• Q: Who should I contact if I have questions about my purchase?
  • A: Please feel free to contact your distributor if you have any kind of questions about your purchase.

PARTS

Tools required

• a. Drive Socket Ratchet Wrench;
• b. 10mm, 13mm, 14mm Wrench;
• c. 10mm, 13mm, 14mm Shallow Socket;
• d. 4mm, 5mm Hex Bit Socket;
• e. Masking Tape;
• f. Cutting Machine;

Installation time

About 1.5 hours, 2-3 people may be needed. Installationtimemaydifferaccording to your mechanical skill level. (PLEASE VERIFY ALL PARTS ARE PRESENT AND READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION!)
To view the electronic version (BXG.9805-S),

please scantheQRcode.

Cutting The Factory Bumper:

• Step 1: Ready to cut the factory bumper. It is strongly recommended for cutting operations.

• Step 2: Take safety precautions: Ensure the vehicle is parkedinasafelocationand wear appropriate safety goggles and gloves during the cutting process.If possible, perform the operation outdoors or in a well-ventilated area.

• Step 3 : Positioning and marking. Identify and mark the areas front bumper that require cutting. It’s important to note that determining the cutting positions on both sides is based on the curve of theinsideofthefactory front bumper, as shown in the picture below. Once theselocationsareconfirmed, use masking tape to mark them.

• Step 4 : Cut the bumper: Carefully cut the bumper usingthechosentool, following the marked positions. Exercise caution to avoid accidental damage or injury, and follow proper cutting techniques. Finishing and refinement: After completing the cut, clean up any debris and refine the cut edges to achieve a neat and smooth appearance.

• Step 5 : If you require the winch bracket, use M10*35 hex boltstofastenitsecurely to the main body

Step 6 : Install the bull bar to the main body and tighten it withM8*20buttonhead socket cap bolts and nuts.

• Step 7 : If you need to install the license plate bracket, use M8*20buttonheadsocket cap bolts and nuts to secure it into the main body, as shown in the diagram.

• Step 8 : Lift the bumper, align it with the holes, and then use the factory bolts to secure the bumper to the vehicle mounting position.

Step 9 : To secure the front bumper, use the connecting bracket and M8*20 button head socket cap bolts to attach it to the factory car bumper.(The connecting bracket ‘1’ is for the driver side, the connectingbracket’2’isforthe passenger side.)

• Step 10 : Finally, use M8*20 button head socket cap bolts toattachthefactoryskid plate to the front bumper.

• Step 11: The installation is complete. We hope you enjoy a wonderful off-road life with this quality Hooke Road product!

Attention:

1. The product parts in this instruction may differ slightly from the actual product contents but generally do not affect the installation the product.
2. Please feel free to contact your distributor if you have any kind of questions about your purchase.

Google Hooke Road to find your parts.

Documents / Resources

| HOOKE ROAD BXG.9805-S Front Bumper [pdf] Installation Guide
BXG.9805-S Front Bumper, BXG.9805-S, Front Bumper, Bumper
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>