HOOKE ROAD BXG.5009 Tundra Front Bumper Offroad Steel Bumper Winch Plate Instruction Manual
- June 1, 2024
- HOOKE ROAD
Table of Contents
HOOKE ROAD BXG.5009 Tundra Front Bumper Off road Steel Bumper Winch Plate
Contents
Parts
| Qty | Part Name | Size(mm) | Picture |
|---|---|---|---|
| 6 | Hex Bolt | M12*30 | |
| 4 | Hex Bolt | M12*110 | 
6| Hex Bolt| M820|
4| Button Head Socket Cap Bolts Screws| M620| *
8| Button Head Socket Cap Bolts Screws| M46|
10| Split Lock Washer| D12| **
6| Split Lock Washer| D8|
14| Flat Washer| M12302|
6| Flat Washer| M8161| 
4| Flat Washer| M6121|
10| Hex Nuts| M12|
6| Flange Hex Lock Nuts| M8| 
4| Nylon Insert Lock Nut| M6|
2| Nylon Round Spacer| M6121.3|
1| L-Wrench| M4|
Tools required
a. Drive Socket Ratchet Wrench;
b. 4mm Hex Bit Socket;
c. 10mm, 13mm, 19mm Wrench;
d. 13mm, 19mm Shallow Socket;
Installation Time
About 1.5 hours, 2-3 people may be needed. Installation time may differ
according to your mechanical skill level. (PLEASE VERIFY ALL PARTS ARE PRESENT
ANDREADINSTRUCTIONSCAREFULLY BEFORE STARTING INSTALLATION!)
To view the electronic version (BXG.5009), please scan the QR code.
Installation Instruction
Step 1: Remove your factory front bumper. Then check the parts and screws
you received and classify them as the contents pictures down.
Step 2: To assemble the wings & the main body. Use the hex
bolts(M1230),split lock washer (D12), flat washer (M12302), hex nuts (M12).
Repeat the installation in the other side. Tighten up those bolts.
Step 3: To assemble the bull bar & the main body. Use the hex
bolts(M820),split lock washer (D8), flat washer (M8161), flange hex
locknuts(M8).Tighten up those bolts.
Step 4: Assemble the license plate bracket (A1, A2, A3)
withtheM620buttonhead socket cap bolts screw groups. And then install it into
the bumper with the M620 button head socket cap bolts screw groups.
Step 5: To install the winch power control box bracket. Use the hex
bolts(M820), split lock washer (D8), flat washer (M8161), flange hex lock
nuts(M8). This step isn’t 100% necessary. Depends if you have the winch power
control box.
Step 6: To install the mounting brackets. Use the hex bolts
(M12110),split lock washer (D12), flat washer (M12302), hex nuts (M12).
Don’t tighten up those bolts.
Step 7: Lift up the bumper and install it into your vehicle with the
factory bolts.
Notes: After adjusting the height of the bumper to achieve the desired
out come and satisfaction, securely tighten both the bolts from step six and
the factory vehicle screws.
Step 8:
The installation is complete. We hope you enjoy a wonderful off-road life with
this quality Hooke Road product!
Attention:
- The product parts in this instruction may differ slightly from the actual product contents but generally does not affect the installation of the product.
- Please feel free to contact your distributor if you have any kind of question about your purchase.
Hooke Road to find your parts.
Feel Free to share your Vehicle @HookRoad4x4 with the Hashing #hookroad If
you’d Like.
