maXpeedingrods ABK-AF1502122-B-VLC 5000 lbs Rear Air Suspension Bags Kit Installation Guide

maXpeedingrods ABK-AF1502122-B-VLC 5000 lbs Rear Air Suspension Bags Kit

FIT FOR FORD
F-150 2WD 4WD
REAR AIR HELPER SPRING LEVELING KIT

AIR SPRING BAG KIT LIST

Mounting brackets

Air Spring Bag and Air line

All Hardware kits

PRE-INSTALLATION NOTICE

• This product will not increase the load capacity of your vehicle.
• Do not exceed the manufacturer’s recommended weight limit.
• The installation process may require drilling, professional installation is recommended to ensure personal safety.
• All modifications must be installed by qualified personnel and in compliance with your local modification regulations.

INSTALLATION GUIDE

ASSEMBLING THE AIR SPRING

NOTE:
This spacer is required if the distance between the upper bracket and the lower bracket is 6.75-7.5″. Otherwise, it is not required.

REMOVING THE JOUNCE BUMPER AND INSTALLING THE UPPER MOUNTING BRACKET

• STEP1.
  Raise the vehicle and support it using safety stands so that the axle can be safely dropped away from the frame, and the air spring assemblies can be put into position between the axle and frame.

• STEP2.
  Remove the jounce bumper from the frame.

• STEP3.
  Thread the hex flange bolt to the bottom of the frame that we just removed the jounce bumper from. Leave about a half inch between the bottom of the frame and the bolt head there.

• STEP4.
  Install the upper mounting bracket, let the flange bolt pass through the keyway in the bracket, then lock the bolt to the frame.

• STEP 5.
  Remove the brake line bracket under the leaf spring on both sides. Remove the plastic clip from the ABS line between the leaf spring and the wheel.

• STEP6.
  Measure the distance between the bottom of the top plate and the top of the bottom plate, and if it’s between 6.75″-7.5″at the factory ride height, the spacers included in the kit will be used.

PLACING THE ASSEMBLY ON THE AXLE

STEP1.
Place the assembly on the alxe.

INSTALLING THE LOWER BRACKET

• STEP1.
  Install the brake line bracket and the lower mounting bracket ( 2 of the Air spring bag kit list) under the leaf spring with hex bolt. Install another hex bolt on the front side of the bracket.

• STEP2.
  Install the fastening block ( 3 of the Air spring bag kit list) with lower mounting bracket to the frame, then tighten the carriage bolts with the nuts.

INSTALLING THE UPPER BRACKET

• STEP1.
  Placing the rolling plate on the top of the air spring bag. Then tighten the bolts with washers and nuts.

• STEP2.
  Place the U-bolt on the frame and through the two holes in the front ofthe upper bracket. Then tighten the bolt with two nuts.

• STEP3.
  Repeat the same installation steps on the other side.

• STEP4.
  You may be able to tie the wire harness and ABS line with zip tie, so it doesn’t rub against anything.

INSTALLING THE WIRING HARNESS

• STEP1.
  Insert the ABS wire into the hole of the wire harness bracket A ( 6 of the Air spring bag kit list). Attach the harness bracket A to the lower bracket. Then tighten the bolt with a washer and a nut.

• STEP2.
  Insert one end of the harness bracket B ( 7 of the Air spring bag kit list) into the harness connector. Attach the other end to the ABS/brake cable connecting bracket. Then tighten the bolt with a washer and a nut.

INSTALLING THE AIR LINES

• STEP1.
  Cut the air line appropriately and push the hose into the fitting, then pull back and make sure it’s locked in place.

• STEP2.
  Install the inflatable valve in a selected location, usually on the license plate at the rear of the vehicle.

CHECK AIRTIGHTNESS

• Put some air into the air spring bag, then spray a soapy solution on all connections and valves while checking for exiting air bubbles.

INSTALLATION COMPLETED

WARNING
Cancer and Reproductive Harm www.P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>