MAXPEEDINGRODS LK-AB-TOYTUN-0714-VLC Air Suspension Bags Kit Installation Guide

June 1, 2024
MAXPEEDINGRODS

MAXPEEDINGRODS LK-AB-TOYTUN-0714-VLC Air Suspension Bags Kit

MAXPEEDINGRODS LK-AB-TOYTUN-0714-VLC Air Suspension Bags Kit

AIR SPRING BAG KIT LIST

Mounting Brackets

1| | 2X Upper mounting bracket| 2| | 2X Lower mounting bracket
3| | 4X Clamp block| 4| | 2X Rolling plate
Air spring bag and Air line
5| Air spring bag and Air line| 2X Air spring bag| 6| | 1X Air line cp6 (5m)
All Hardware kits
7| | 4X Hex head
flange bolt
M101.520| 8| | 4X Hex bolt
3/S-24UNF20
9| | BX Carriage
bolt MS
1.2551| 10| | 4X U-bolt
M10
1.590-90122
11| | 4X Hex screw
M101.516| 12| | BX Hex lock nut
M101.5
13| | BX Hex lock nut
MS
1.25| 14|
| 1OX Flat
washer MS
15| | 12X Flat
washer M10| 16| | 2X 90° Air Hose
fitting R2 l/S
17| | 2X Inflation valve
8V1 (with cap)| 18| | 4X Hex nut 8V1
19| | 2X Anti-slip
gasket øp8| 20| | 2X Rubber
gasket øpl7 72
21| | 6X Zip tie| 22| | 4XWasher
MS

PRE-INSTALLATION NOTICE

  • This product will not increase the load capacity of your vehicle.
  • Do not exceed the manufacturer’s recommended weight limit.
  • The installation process may require drilling, professional installation is recommended to ensure personal safety.
  • All modifications must be installed by qualified personnel and in compliance with your local modification regulations.

INSTALLATION GUIDE

Installation Guide

ASSEMBLING THE AIR SPRING

Assembling The Air Spring
Assembling The Air Spring

NOTE:
The holes for installing the upper bracket are different on the driver’s side and the passenger’s side.

REMOVING THE JOUNCE BUMPER AND PLACING THE ASSEMBLY ON THE AXLE

STEP1. Raise the vehicle and support it using safety stands so that the axle can be safely dropped away from the frame, and the air spring assemblies can be put into position between the axle and frame.
STEP2. Bend the brake line bracket forward to gain room for the lower bracket.
Removing The Jounce Bumper And Placing The Assembly On The
Axle
STEP3. Cut and leave 3/4″ of the jounce bumper on the leaf spring.
Removing The Jounce Bumper And Placing The Assembly On The
Axle
STEP4. Place the assembly on the leaf spring and let the air fitting pass through the hole in the frame.
Removing The Jounce Bumper And Placing The Assembly On The
Axle

INSTALLING THE UPPER BRACKET

STEP1. Install the clamp block ( 3 of the Air spring bag kit list) to the frame.
And secure the clamp block to the upper mounting bracket with the carriage bolts( 9) of the Air spring bag kit list).
Installing The Upper Bracket

INSTALLING THE LOWER BRACKET

STEP1. Adjust the assembly so that the air spring is perpendicular to the bottom and top mounting brackets without twisting.
STEP2.  Install the lower mounting bracket to the leaf spring with U-bolts (10) of the Air spring bag kit list).
Installing The Lower Bracket
NOTE: If necessary, you can trim the excess length on the nut of the U-bolt.
STEP3. Repeat the same installation steps on the other side.

INSTALLING THE AIR LINES

STEP1. Cut the air line appropriately and push the hose into the fitting then pull back and make sure it’s locked in place.
Installing The Air Lines
STEP2. Install the inflatable valve in a selected location, usually on the license plate at the rear of the vehicle.
Installing The Air Lines

CHECK AIR TIGHTNESS

  • Put some air into the air spring bag, then spray a soapy solution on all connections and valves while checking for exiting air bubbles.

INSTALLATION COMPLETED

WARNING
Cancer and Reproductive Harm www.P65Warnings.ca.gov

Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

MAXPEEDINGRODS User Manuals

Related Manuals