MAXPEEDINGRODS ABK-ASIE0719-B-VLC Rear Air Suspension Bags Kit Installation Guide

June 1, 2024
MAXPEEDINGRODS

MAXPEEDINGRODS Logo AIR SPRING KIT
Installation Guide FIT FOR GMC SIERRA
CHEVROLET SILVERADO 1500
REAR AIR HELPER SPRING LEVELING KIT

AIR SPRING BAG KIT LIST

Mounting brackets

1| | 1X Driver’s side upper mounting bracket| 2| MAXPEEDINGRODS ABK-
ASIE0719-B-VLC Rear Air Suspension Bags Kit - Upper| 1X Passenger’s side
upper mounting bracket| 3| | 2X Lower mounting
bracket
---|---|---|---|---|---|---|---|---
4| | 2X Fastening block| | | | | |

Air Spring Bag and Air line

1 2X Air spring bag 2 1X Air line φ6*1 (5m)

All Hardware kits

7| | 6X Zip tie (1905)| 8| | 2X U-bolt 3/8-1690-89122| 9| | 2X 90° Air fitting 01/8 06 (male)
---|---|---|---|---|---|---|---|---
10| | 2X Inflation valve 8V1 (with cap)| 11| | 2X Carriage bolt 3/8-16UNC
127| 12| | 2X Bushing (1)20(p1182
13| | 2X Hex bolt 5/16- 18UNC38-25| 14| | 2X Rubber gasket 917(/)72| 15| | 2X Plastic hex nut G1/26
16| | 2X Anti-slip gasket (p8| 17| | 6X Flat washer M10| 18| | 2X Flat washer M14
19| | 2X Lock washer M20| 20| | 6X Hex ny nylon nut 3/8-16UNC| 21| | 2X Lock washer MM
22

| | 2X Hex nylon nut 5/16-18UNC| 23| | 4X Hex thin nut 8Vthi1 (ck)3mm| 24| | 2X Larger washer M10
25| | 2X Large washer p70(00.55| 26

| | 2X Flat washer M8| 27| | 2X Hex nut 1/2-13UNC25
28| | 2X R type pipe clamp q)10
(p9|

PRE-INSTALLATION INSTRUCTION

  • This product will not increase the load capacity of your vehicle.
  • Do not exceed the manufacturer’s recommended weight limit.
  • The installation process may require drilling, professional installation is recommended to ensure personal safety.
  • All modifications must be installed by qualified personnel and in compliance with your local modification regulations.

INSTALLATION GUIDE

MAXPEEDINGRODS ABK-ASIE0719-B-VLC Rear Air Suspension Bags Kit - Driver
Side

ASSEMBLING THE AIR SPRING

MAXPEEDINGRODS ABK-ASIE0719-B-VLC Rear Air Suspension Bags Kit - Air
Sprimg

INSTALLING THE UPPER BRACKET

STEP 1.
Raise the vehicle and support it using safety stands so that the axle can be safely dropped away from the frame, and the air spring assemblies can be put into position between the leaf spring and frame.
STEP 2.
Remove the wheels.
STEP 3.
Pry the ABS sensor harness clip from the bottom of the frame and remove the stock ABS sensor harness clip. Then install the new R type pipe clamp ( 28 of the Air spring bag kit list) on the harness. MAXPEEDINGRODS ABK-
ASIE0719-B-VLC Rear Air Suspension Bags Kit - Air Sping
BagSTEP4.
Insert the hex bolt and washer through the hole on the outside of the frame, and let them pass through the bottom of the frame.MAXPEEDINGRODS ABK-
ASIE0719-B-VLC Rear Air Suspension Bags Kit - Hex Bolt 1 STEP 5.
Attach the upper bracket ( 1 of the Air spring bag kit list) to the axle, and make sure the previously inserted bolt goes through the hole in the bottom of the bracket. Then tighten the bolt with R clamp, washer and nut. MAXPEEDINGRODS ABK-ASIE0719-B-VLC Rear Air Suspension Bags Kit -
ClampSTEP 6.
Insert the carriage bolt ( 11 of the Air spring bag kit list) through the upper bracket, frame and bushing ( 12 of the Air spring bag it list).
Then tighten the bolt with a larger washer and nut.MAXPEEDINGRODS ABK-
ASIE0719-B-VLC Rear Air Suspension Bags Kit - Clamp 1

PLACING THE ASSEMBLY ON THE LEAF SPRING

STEP1.
Place the assembly on the leaf spring. MAXPEEDINGRODS ABK-ASIE0719-B-VLC
Rear Air Suspension Bags Kit - Leaf Spring

INSTALLING THE AIRFITTING

STEP1.
Put the plastic hex thin nut (15 of the Air spring bag kit list) and lock washer (19 of the Air spring bag kit list) on the upper threaded post of the air spring, and tighten it after the installation is completed. MAXPEEDINGRODS ABK-ASIE0719-B-VLC Rear Air Suspension Bags Kit - spring
bag

INSTALLING THE LOWER BRACKET

STEP 1.
Adjust the assembly so that the air spring is perpendicular to the bottom and top mounting brackets without twisting.
STEP 2.
Attach the lower mounting bracket (3 of the Air spring bag kit list) to the leaf spring, then tighten the fastening block (4 of the Air spring bag kit list) with U-bolt, washers and nuts, The passenger’s side is the same way. MAXPEEDINGRODS ABK-ASIE0719-B-VLC Rear Air Suspension Bags Kit -
Nuts

INSTALLING THE AIR LINES

STEP 1.
Cutthe airline appropriately and push the hose into the fitting, then pull back and make sure it’s locked in place. MAXPEEDINGRODS ABK-ASIE0719-B-VLC
Rear Air Suspension Bags Kit - LockedSTEP 2.
Install the inflatable valve in a selected location, usually on the license plate at the rear of the vehicle.

MAXPEEDINGRODS ABK-ASIE0719-B-VLC Rear Air Suspension Bags Kit -
License

CHECK AIR TIGHTNESS

  • Put some air into the air spring bag, then spray a soapy solution on all connections and valves while checking for exiting air bubbles.

INSTALLATION COMPLETED
WARNING
Cancer and Reproductive Harm
Www.PE5Warnings.ca.gov
ABK-ASIE0719-B-VLC

MAXPEEDINGRODS Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

MAXPEEDINGRODS User Manuals

Related Manuals