HOOKE ROAD BXG.8283 Rear Bumper Installation Guide
- June 1, 2024
- HOOKE ROAD
Table of Contents
HOOKE ROAD BXG.8283 Rear Bumper
Specifications:
- Part Number: BXG.8283
- Contents:
- 12 Hex Bolts Size(mm) M12*35
- 12 Split Lock Washer D12
- 24 Flat Washer M12302
- 12 Hex Nuts M12
- 8 Button Head Socket Cap Bolts Screws M6*16
- 8 Button Head Socket Cap Bolts Screws M4*16
- 1 L-Wrench M4
- 4 Sensor Brackets
Tools Required:
Drive Socket Ratchet Wrench; b. 10mm, 19mm Wrench; c. 19mm Shallow Socket; d. 4mm Hex Bit Socket;
Installation Time:
About 1 hour, 1-2 people may be needed. Installation time may differ according to your mechanical skill level.
(PLEASE VERIFY ALL PARTS ARE PRESENT AND READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION!)
To view the electronic version (BXG.8283), please scan the QR code.
Installation Instructions
With the factory tow hook:
- Remove the original car rear bumper radar harness using a 10mm wrench.
- Insert the plug of the original car radar harness into the corresponding radar socket and secure it with M4*16 screws.
- Secure the radar to the rear bumper using sensor brackets.
- Fasten the bumper using M12*35 screws with washers and nuts.
Without the factory tow hook:
- Remove the original car rear bumper.
- Mount the brackets on the bumper using M12*35 screws.
- Secure the bumper using M12*35 screws with washers and nuts.
- Install the provided square lights into the bumper using M6*16black screws.
Attention:
- The product parts in this instruction may differ slightly from the actual product contents but generally does not affect the installation of the product.
- Please feel free to contact your distributor if you have any kind of question about your purchase.
FAQ:
Q: How do I know if I have correctly installed the rear bumper?
A: Once you have securely fastened the bumper using the specified screws
and washers, ensure that it is aligned properly with the vehicle mounting
holes and does not shake or move when lightly pushed. Additionally, check that
all components are properly connected and tightened.
Q: Can I install the rear bumper alone?
A: While it is recommended to have assistance during installation, it is
possible to install the rear bumper alone if you follow the step-by-step
instructions carefully and have the necessary tools at hand. However, having
an extra pair of hands can make the process easier and safer.
Rear Bumper
BXG.8283
Contents
TOOLS
Tools required
- Drive Socket Ratchet Wrench;
- 10mm, 19mm Wrench;
- 19mm Shallow Socket;
- 4mm Hex Bit Socket;
Installation time
About 1 hour, 1-2 people may be needed. Installation time may differ according
to your mechanical skill level.
(PLEASE VERIFY ALL PARTS ARE PRESENT AND READ INSTRUCTIONS CAREFULLY BEFORE
STARTING INSTALLATION!)
To view the electronic version (BXG.8283), please scan the QR code.
Installation instruction
Step 1: First, remove the original car rear bumper radar harness. Use a 10mm wrench to unscrew the screws behind the original car bracket, and then unplug the harness connector.
Step 2: Insert the plug of the original car radar harness into the
corresponding radar socket, secure the radar to the rear bumper using the
sensor bracket, and fasten it with M4*16 screws to prevent shaking or damage
during driving.
Put the trailer connector into the bumper.
We provide instructions for two installation methods, please choose one method to install according to the situation of your car.
With the factory tow hook
Step 3: Before installing our product, ensure that the vehicle is parked in a safe and level location, and remove the original car rear bumper.
Step 4: It is recommended to install the bumper with assistance. Lift the bumper, align it with the original vehicle mounting holes, and secure it using M12*35 screws with washers and nuts. Adjust the gap from the vehicle and tighten the screws.
Without the factory tow hook
Step 5: Before installing our product, ensure that the vehicle is parked in a safe and level location, and remove the original car rear bumper.
Step 6: Next, the mounting brackets need to be mounted on the bumper. Use M12*35 screws to assemble them. Repeat the same procedure on the other side.
Step 7: It is recommended to install the bumper with assistance. Lift the bumper, align it with the original vehicle mounting holes, and secure it using M12*35 screws with washers and nuts. Adjust the gap from the vehicle and tighten the screws.
Step 8: Finally, install the provided square lights into the bumper. Use M6*16 black screws for the installation.
Step 9:
The installation is complete. We hope you enjoy a wonderful off-road life with
this quality Hooke Road product!
Attention:
- The product parts in this instruction may differ slightly from the actual product contents but generally does not affect the installation of the product.
- Please feel free to contact your distributor if you have any kind of question about your purchase.
Google Hooke Road to find your parts.
Feel Free To Share Your Vehicle @HookeRoad4x4
With The Hashtag #hookeroad If You’d Like
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>