HOOKE ROAD BXG.9024 Full Width Front Bumper and Rear Bumper Installation Guide

HOOKE ROAD BXG.9024 Full Width Front Bumper and Rear Bumper

Specifications

• Part Name: Rear Bumper
• Contents:
  • BXG.9024
  • BXG.9025-1
  • Qty 1
  • Part Name Rear Bumper Hex Bolt Hex Bolt Hex Bolt Button Head Socket Cap Bolts Screws Button Head Socket Cap Bolts Screws Hex Nylon Lock Nuts
  • Size(mm): M1245, M1235, M1050, M616, M4*10, M10
  • Part Name Hex Nylon Lock Nuts Hex Nylon Lock Nuts Flat Washer Flat Washer Flat Washer Flat Washer
  • Size(mm): M12, M6, M6121, M10302, M12302, M12302

Installation Instructions

1. Tools required:
   • 2mm & 4mm Allen Wrench
   • 16mm & 19mm Shallow Socket
   • Drive Socket Ratchet Wrench
2. Installation Time: About 1.5 hours, 2-3 people may be needed. Installation time may differ according to your mechanical skill level.
3. Installation Steps:
4. 1. Passenger/right side installation Step 1: Remove bumper bolts from outside of frame arrows. The passenger side is pictured below.

FAQ

• Q: What if I encounter missing parts during installation?
• A: If you find any parts missing, please contact your distributor for assistance.

Rear Bumper

• BXG.9024
• BXG.9025-1

Contents

Qty| Part Name| Size(mm)| Qty| Part Name| Size(mm)
---|---|---|---|---|---
1| Rear Bumper|  | N×10| Hex Nylon Lock Nuts| M12
H×6| Hex Bolt| M1245| O×4| Hex Nylon Lock Nuts| M6
I×4| Hex Bolt| M1235| P×8| Flat Washer| M6121
J×2| Hex Bolt| M1050| Q×4| Flat Washer| M10302
K×4| Button Head Socket Cap Bolts Screws| M616| R×12| Flat Washer| M12302
L×8| Button Head Socket Cap Bolts Screws| M410| S×8| Flat Washer| M1230*2
M×2| Hex Nylon Lock Nuts| M10|  |  |

Notes: This manual is suitable for installing rear bumper A or rear bumper B.

Tools required

• 2mm & 4mm Allen Wrench;
• 16mm & 19mm Shallow Socket;
• Drive Socket Ratchet Wrench;

Installation time

• About 1.5 hours, 2-3 people may be needed. Installation time may differ according to your mechanical skill level.
• (PLEASE VERIFY ALL PARTS ARE PRESENT AND READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION!)
• To view the electronic version (BXG.9024 & BXG.9025-1), please scan the QR code.

Installation instruction

Passenger/right-side installation
Step 1
Remove bumper bolts from the outside of the frame（arrows The passenger side is pictured below.

Step 2
Remove bumper bolt from the bottom of the frame arrow The back of the passenger side of the model w-o receiver hitch is pictured below.
2014-2016 models, remove the rear bed to frame bolts, and loosen centre bolts, (if equipped). Do not loosen the front bolts.

Step 3
Remove bumper bolts attaching brackets to frame (arrows). Model with the receiver hitch is pictured below.

Notes: Before removing hardware, fully support the weight of the bumper with blocks or stands to prevent injury or damage to the vehicle.

Step 4
OPTION 2014-16 only: Release clips to remove plastic bumper cover (arrow). The passenger side is pictured below.

Step 5
OPTION 2014-2016 only: Remove bumper bolts attaching bumper to inner bracket. Remove the outer bumper first, then remove the inner brackets.

Step 6
End of the frame once the factory bumper is removed. Passenger side w-o receiver hitch pictured.

• Notes: Before removing hardware, fully support the weight of the bumper with blocks or stands to prevent injury or damage to the vehicle.

Step 7
End of the frame once the factory bumper is removed. Passenger side with receiver hitch pictured.

Step 8
Attach the Bumper Bracket to the side mounting holes in the frame and hitch if equipped.

Step 9
Attach the passenger side of the Bumper to the frame. Model w-o receiver hitch pictured.

Step 10
Model with receiver hitch with support strap pictured.

Step 11
Attach Bumper to frame brackets.

Step 12
Install the trailer Plug Bracket as the picture shows.

Step 13
Push the sensor into the mounting sleeve. Use 4mm Screws to lock the sensor in place.

Notes: Sensors fit snugly in sockets. The 4mm Screws are only used to apply slight pressure to lock the sensors in place. Tighten both screws evenly until they touch the sensor body only. Do not overtighten screws or damage to sensors will result.

Step 14
The installation is complete. We hope you enjoy a wonderful off-road life with this quality Hooke Road product!

Attention

1. The product parts in this instruction may differ slightly from the actual product contents but generally do not affect the installation of the product.
2. Please feel free to contact your distributor if you have any kind of questions about your purchase.

Google Hooke Road to find your parts

• @HookeRoad4x4 Post Your Jeep/Truck w/Hashtag #hookeroad to Win Discount Every Week

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>