HD Ridez WB-FN189BD Drop Down Style Running Boards Instruction Manual
- June 1, 2024
- HD Ridez
Table of Contents
HD Ridez WB-FN189BD Drop-Down Style Running Boards
Specifications:
- Compatible with: 15-24 Ford F-150 Regular Cab, 17-24 Ford F250/350 Super Duty Regular Cab
- Part Numbers : WB-FN189MD (Driver/Left) / WB-FN189BD (Passenger/Right)
- Includes: 1 Driver/Left NB1 Running Board, 1 Passenger/Right NB1 Running Board, 4 Mounting Brackets, 8 10-1.5mm x 35mm Hex Bolts, 16 10mm x 27mm x 3mm Flat Washers, 8 10-1.5mm Nylon Lock Nuts, 12 8mm Plastic Washers, 12 8mm x 24mm x 2mm Flat Washers, 12 8-1.25mm Nylon Lock Nuts
Installation Instructions:
- Step 1: Preparation
- Remove all contents from the box and verify all parts are present. Read the instructions carefully before starting the installation.
- Step 2: Mounting Studs Preparation
- Start on the Driver/Left front of the vehicle. Locate the threaded mounting studs in the rocker panel and clean them with a wire brush to remove paint and debris.
- Step 3: Installing Plastic Washers
- Slide one Plastic Washer over each of the factory mounting studs in the rocker panel. Do not use any polish or wax that may contain abrasives.
- Step 4: Mounting Brackets Installation
- Follow the provided diagrams and attach the Mounting Brackets according to the instructions.
- Step 5: Attaching Running Board
- Attach the Running Board to the rear-facing side of the Mounting Brackets as shown in the diagrams.
- Step 6: Finalizing Installation
- Secure the Running Board to the front and rear Mounting Brackets to complete the installation process.
FAQ
- Q: Can these running boards be installed on other vehicle models?
- A : These running boards are specifically designed for 15-24 Ford F-150 Regular Cab and 17-24 Ford F250/350 Super Duty Regular Cab models. Using them on other vehicles may not provide proper fitment.
- Q: What maintenance is required for these running boards?
- A : To maintain these running boards, avoid using abrasive polishes or waxes. Mild soap can be used for cleaning. Regularly check for any loose bolts or brackets and tighten them if needed.
PARTS LIST
PROCEDURE
-
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
-
Starting on the Driver/Left front of the vehicle, locate the threaded mounting studs in the rocker panel,
(Figure 1). Clean mounting studs with wire brush to remove paint and debris. -
Slide (1) Plastic Washer over each of the (3) factory mounting studs in the rocker panel. IMPORTANT: The Plastic Washers are designed to prevent corrosion between the aluminum rocker panel and the steel mounting brackets. Do not install the Brackets without the Plastic Washers.
-
Select (1) Mounting Bracket. NOTE: All (4) Brackets are universal and will fit left or right in all mounting locations. Attach the Mounting Bracket to the (3) factory studs with (3) 8mm Flat Washers and (3) 8mm Nylon Lock Nuts, (Figures 2 & 3). Do not tighten the hardware at this time.
-
Repeat Steps 2—4 to install the Rear Bracket, (Figures 4 & 5). Do not tighten hardware at this time.
-
Select the Driver/Left Running Board. Attach the Running Board to the rear-facing side of the Mounting Brackets with (4) 10mm Hex Bolts, (8) 10mm Flat Washers and (4) 10mm Nylon Lock Nuts, (Figures 6—8). Do not tighten the hardware at this time.
-
Level and adjust the Running Board as necessary and fully tighten all hardware.
-
Repeat Steps 2—7 for Passenger/Right Running Board installation.
-
Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment, Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used to clean the Running Board.
Installation
Driver/Left Side Installation Pictured
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>