Shenzhen Kingree Intelligent Digital HP1375 True Wireless Earbuds User Manual
- June 6, 2024
- Shenzhen Kingree Intelligent Digital
Table of Contents
Shenzhen Kingree Intelligent Digital HP1375 True Wireless Earbuds
Product parameter
- Bluetooth version: VS.1
- Output voltage: DCSV
- Output power: SmW-2
- Earbuds capacity: 30mAh*2
- Charging time: about 1.5h
- Talk time: about 2h
- Connection distance: 10M
- Impedance : 320
- Speaker size: 13mm
- Playing time: about 2.Sh
- Standby time: about 20h
Key operation
Control music:
- Play/pause: Tap the left or right earbud once
- Next song: Double click the right earbud
- Last song: Double cllck the left earbud
CALLS
- Answer the call: Tap the left or right earbud once
- Hang up the call: Tap the left or right earbud once again
- Reject the call: press and hold for 2 seconds
Voice assistant mode (support 105 & Android):
Click left or right earbud three times to activate the voice assistant (The call supports bilateral calls, that is, double earphones are used for sound, and single earphones are also supported for calling functions)
Instructions
**Bluetooth pairing
**
- Take out the left and right earphones from the charging box, and there wlll be a “beep” tone, indicating that the left and right earphones are connected and paired.
- After the left and right earphones are successfully paired, tum on the Bluetooth of the mobile phone, and click the Bluetooth name of the device in the Bluetooth search box of the mobile phone. after the headset and the mobile phone are successfully connected, there will be a “beep” tone.
- The left and right earphones can be used at the same time or separately.
LED blinking method
- The charging box charges the earphones: the green light of the charging box Is constant on and the earphones are fully charged and the green light will be off going out.
- Charging the charging box: the red light of the charging box flashes, and the red llght Is always on after being fully charged.
Charging the earbuds
Put the earphone into the charging box, it will automatically enter the charging state.
Charging box charging
Use the USB cable to charge the charging box, the charging box indicator light flashes red to indicate that it is charging, and the red led lights constantly to indicate that it is fully charged.
On/off
- Turn on: the left and right earphones are taken out of the charging box, and the left and right earphones are automatically turned on for pairing with each other.
- Turn off: the headset will automatically turn off when being placed in the charging box; it will automatically be turned off after 5 minutes of power on and there is no input audio signals.
Precautions
- Do not disassemble or modify this product by yourself
- Too high volume may cause permanent damage to hearing, avoid using this tws earphones al high volume for a long time.
FCC STATEMENT :
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause hannful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
RF warning statement:
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>