HD Ridez WB-DR208BD Overland Slider Drop Steps Instruction Manual

: June 1, 2024
: HD Ridez

Table of Contents

HD Ridez WB-DR208BD Overland Slider Drop Steps
Product Information
Product Usage Instructions
PARTS LIST
OVERVIEW
INSTALLATION INSTRUCTION
Read User Manual Online (PDF format)
Download This Manual (PDF format)

HD Ridez WB-DR208BD Overland Slider Drop Steps

Product Information

Specifications:

Product: RS6 Overland Slider Drop Steps
Compatibility: 09-18 Dodge Ram 1500 Crew Cab (incl 2019-24 Classic), 10-24 Dodge Ram 25-5500 Crew Cab (incl Chassis Cab Diesel Models)
Part Number: WB-DR208BD
Material: Steel
Finish: Black Powder Coat
Includes: Driver/Left Running Board, Passenger/Right Running Board, Drop Steps, Mounting Brackets, Bolts, Washers, Nuts, Plates

Product Usage Instructions

Parts List:

Driver/Left Running Board
Passenger/Right Running Board
Drop Steps (4)

Installation Procedure:

Remove all contents from the box and verify all parts are present.
Read the instructions carefully before starting the installation as drilling may be required.
Start at the driver side-front of the vehicle and remove the sealing tape covering the factory holes in the inner panel.

Cleaning and Maintenance:
To protect your investment, do not use any polish or wax containing abrasives that could damage the finish. Mild soap can be used to clean the Overland Steps.

FAQ:

Q: Do I need any special tools for the installation?
A: Basic hand tools such as a wrench and a drill may be required for the installation process.
Q: Can these drop steps be installed on a different vehicle model?
A: These drop steps are specifically designed for the mentioned Dodge Ram models. Installing them on a different model may require modifications and adjustments.

PARTS LIST

1	Driver/Left Running Board	6	8mm Bolt/Nut Plates
1	Passenger/Right Running Board	18	8mm x 30mm Hex Bolts
4	Drop Steps	24	8mm x 24mm OD x 2mm Flat Washers
3	Driver Front/Passenger Rear Mounting Brackets	16	8mm x 22mm OD x 2mm Flat

OVERVIEW

INSTALLATION INSTRUCTION

PROCEDURE: REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. DRILLING MAY BE REQUIRED.

Starting at the driver side-front of the vehicle, remove the sealing tape covering the factory holes in the side of the inner panel, (Figure 1).
Determine the correct procedure to attach the driver side front Bracket for your model/year:
Models without factory threaded inserts in body panel:
- a. Select (1) 8mm Bolt/nut Plate, (Figure 2). Partially thread an 8mm Hex Bolt onto the threaded of the Nut Plate, (Figure 3). Thread the Hex Bolt in until it is flush with the welded nut. Use the Hex Bolt as a handle and insert the Bolt and Nut Plate into the oval hole, (Figure 4). Feed the threaded bolt on the Bolt Plate through one of the hex shaped factory holes.
- b. Thread (1) 8mm Plastic Retainer onto the threaded end and down tight against the body panel,(Figure 5). NOTE: The Plastic Retainer is designed to keep the Bolt/Nut Plate from falling into the body panel and to aid in Bracket installation.
- c. Select (1) Driver/Left Bracket, (Figure 6). Attach the Bracket to the threaded end of the Bolt Plate with (1) 8mm Flat Washer, (1) 8mm Lock washer and (1) 8mm Hex Nut, (Figure 6).
  IMPORTANT: Driver/Left Front Bracket is the same as the Passenger/Right Center and Rear Brackets. Do not tighten hardware at this time.
- d. Remove the 8mm Hex Bolt from the nut on the Bolt Plate from Step 2a. Rotate the Bolt on the Bolt Plate until the threaded nut lines up with the remaining hole in the Mounting Bracket and body panel, (Figure 7). Attach the Bracket to the threaded Nut Plate with (1) 8mm x 30mm Hex Bolt, (1) 8mm Lock Washer and (1) 8mm Flat Washer, (Figure 7). Do not tighten hardware.
  Models with factory threaded inserts:
- a. Attach (1) Driver/Left Mounting Bracket to the threaded inserts with (2) 8mm x 30mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washer, (Figures 8 & 9). Do not tighten hardware.
Attach (1) Support Bracket to the back of the pinch weld with (2) 6mm Hex Bolts, (4) 6mm Flat Washers and (2) 6mm Nylon Lock Nuts, (Figure 10). Do not fully tighten hardware. IMPORTANT: 2009-12 models not equipped with factory holes will require drilling through the pinch weld to fully attach Bracket. Do not drill through pinch weld at this time, (see Step 8).
Attach the Support Bracket to the Mounting Bracket with (1) 8mm Hex Bolt, (2) 8mm Flat Washers and (1) 8mm Nylon Lock Nut, (Figure 11). Do not tighten hardware at this time.
Move along the side of the body panel to the center mounting location, (Figure 12). Repeat Steps 1—4 to install (1) Driver/Left Center Mounting Bracket to the center mounting location.
Move to the rear location, (Figure 13). Repeat Steps 1—4 to attach (1) Passenger/Right Front Mounting Bracket to the Driver/Left rear mounting location.
Select the Driver/Left Tube. Insert (2) 8mm Double Bolt Plates into the front (2) sets of (2) holes, (Figure 14). Attach (1) Drop Step to the (2) Double Bolt Plates with (4) 8mm x 22mm Flat Washers and (4) 8mm Nylon Lock Nuts, (Figure 15). Do not tighten hardware.
With assistance, line up the mounting tabs in the Driver/Left Tube to the rear faces of the Mounting Brackets. Secure the Tube to the Mounting Brackets with (6) 10mm Hex Bolts, (12) 10mm Flat Washers and (6) 10mm Nylon Lock Nuts, (Figure 16). Do not tighten hardware.
Properly level and adjust the Side Step and fully tighten all hardware.
2009-12 models requiring drilling through pinch trim:
- a. Level the Side Step to the vehicle. Make sure all (3) Brackets are tight against the bottom of the body panel and tighten all mounting hardware.
- b. Mark the location of the slots onto the pinch weld.
- c. Drill (2) 1/4” holes through the pinch weld for each Bracket. IMPORTANT: Do not drill too close to the bottom edge of the pinch weld. Drill the holes in the center of the marked slots.
- d. Repeat Step 3 to attach the Brackets to the drilled holes in the pinch weld. Check for level then fully tighten all hardware.
Repeat Steps 1—8 to attach the Passenger/Right Overland Drop Steps.
Do periodic inspections to the installation to make sure that all hardware is secure and tight.

To protect your investment, Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used to clean the Overland Steps.