HD Ridez WB-FS175SD Style Matte Nerf Bars Running Boards Instruction Manual
- June 1, 2024
- HD Ridez
Table of Contents
HD Ridez WB-FS175SD Style Matte Nerf Bars Running Boards
Product Information
Specifications:
- Compatible with: 2015-2024 F150 Crew Cab, 2022-2024 F150 Lightning, 2017-2024 F250-550 Super Duty Crew Cab
- Part Numbers: WB-FS175SD (Driver/left Running Board), WB-FS175BD (Passenger/right Running Board)
- Parts Included: 1 Driver/left Running Board, 1 Passenger/right Running Board, 6 Mounting Brackets, 18 8mm Plastic Washers, 30 8mm x 24mm OD x 2mm Washers, 30 8mm Nylon Lock Washers, 6 8mm Double Bolt Plates
Product Usage Instructions
Installation Steps:
- Ensure the surface is clean before starting the installation process.
- Identify the driver/left and passenger/right running boards along with the mounting brackets and washers.
- Attach the mounting brackets to the designated locations on the vehicle body panel using the provided hardware.
- Secure the running boards to the mounting brackets by following the specific instructions for each component.
- Check and tighten all connections to ensure a secure fit.
Cleaning Instructions:
To maintain the running boards, avoid using abrasive polishes or waxes
that could damage the finish. Instead, use mild soap and water to clean the
running boards as needed.
FAQs
-
Q: Can these running boards be installed on a different vehicle model?
A: These running boards are specifically designed for use with the mentioned vehicle models. Installing them on other models may not guarantee proper fitment. -
Q: Are these running boards compatible with aftermarket accessories?
A: Compatibility with aftermarket accessories may vary. It is recommended to check with the manufacturer or retailer for specific compatibility information.
PARTS LIST
| 1 | Driver/left Running Board | 30 | 8mm x 24mm OD x 2mm Washers |
|---|---|---|---|
| 1 | Passenger/right Running Board | 30 | 8mm Nylon Lock Washers |
| 6 | Mounting Brackets | 6 | 8mm Double Bolt Plates |
| 18 | 8mm Plastic Washers |
OVERVIEW
INSTALLATION INSTRUCTION
PROCEDURE:
-
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
-
Start the installation under either side of the vehicle. Locate the front factory mounting location along the inner side of the body, (Figure 1). Use a wire brush or thread chaser die to remove excess paint and/or undercoating from all studs.
-
Slide (1) Plastic Washer over each of the (3) factory mounting studs in the body panel, (Figures 2—4).
IMPORTANT: The Plastic Washers were designed to prevent corrosion between the aluminum body panel and the steel mounting brackets. Do not install the Brackets without the Plastic Washers. -
Select (1) Mounting Bracket. Attach the Bracket to the studs with (3) 8mm Flat Washers and (3) 8mm Nylon Lock Nuts, (Figure 4). Do not tighten hardware.
-
Repeat Step 3 to attach (1) Mounting Brackets to the center and (1) Mounting bracket to the rear mounting locations.
-
Select the Running Board. Select (3) Double Bolt Plates. Insert the Bolt Plates into the channel in the bottom of the Running Board closest to the Brackets, (Figure 5). Lift the Running Board up and guide the studs through the Brackets.
-
Attach the Running Board to the Mounting Brackets with, (6) 8mm Flat Washers and (6) 8mm Nylon Lock Nuts, (Figure 6). Do not tighten hardware.
-
Level and adjust the Running Board and tighten all hardware.
-
Repeat Steps 1—8 to attach the other Running Board.
-
Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment, Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used to clean the Running Board.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>