HD Ridez HW-WB-TT298 Blow Molding Running Boards Instruction Manual

June 1, 2024
HD Ridez

HD Ridez HW-WB-TT298 Blow Molding Running Boards

HD-Ridez-HW-WB-TT298-Blow-Molding-Running-Boards-
PRODUCT

Product Information

Specifications:

  • Product Name : P1 Running Boards
  • Compatible with : 2022-2024 Toyota Tundra CrewMax/Double Cab
  • Part Number : HW-WB-TT298
  • Parts Included:
    • 1 Driver/Left P1 Running Board
    • 1 Passenger/Right P1 Running Board
    • 1 Driver/Left Front Mounting Bracket
    • 1 Passenger/Right Front Mounting Bracket
    • 3 Driver/Left Rear Mounting Brackets
    • 3 Passenger/Right Rear Mounting Brackets
    • 16 8mm x 30mm Hex Bolts
    • 16 8mm Lock Washers
    • 16 8mm x 24mm OD x 2mm Flat Washers
    • 8 6mm Double Bolt Plates
    • 16 6mm x 22mm OD x 2mm Flat Washers
    • 16 6mm Lock Washers
    • 16 6mm Hex Nuts

Product Usage Instructions

Step 1: Preparation

Ensure you have all the parts listed in the specifications section.

Step 2: Cleaning

To clean the running boards, use only mild soap. Do not use abrasive polish or wax that could damage the finish.

Step 3: Installation – Passenger/Right Side

  1. Remove plastic plugs or hex bolts from threaded holes at the front mounting location.
  2. Attach the Driver/Left Front Mounting Bracket to the front location using provided bolts, lock washers, and flat washers.
  3. Attach the Passenger/Right Front Mounting Bracket to the front location using the same hardware.
  4. Move to the center (2nd) location and attach the Passenger/Right Rear Mounting Bracket using the provided hardware.
  5. Insert a Double Bolt Plate into the channel on the bottom of the Running Board at this location.
  6. Secure the Running Board to the Mounting Brackets using the specified hardware.

FAQ

  • Q: Can these running boards be installed on other vehicle models?
    • A: These running boards are specifically designed for use with the 2022-2024 Toyota Tundra CrewMax/Double Cab and may not be compatible with other models.
  • Q: How should I clean the running boards?
    • A: Use mild soap and avoid abrasive polishes or waxes that could damage the finish of the running boards.

PARTS LIST

1 Driver/Left P1 Running Board 16 8mm lock Washers
1 Passenger/Right P1 Running Board 16 8mm x 24mm OD x 2mm Flat Washers
1 Driver/Left Front Mounting Bracket 8 6mm Double Bolt Plates
1 Passenger/Right Front Mounting Bracket 16 6mm x 22mm OD x 2mm Flat

Washers
3| Driver/Left Rear Mounting Brackets| 16| 6mm Lock Washers
3| Passenger/Right Rear Mounting Brackets| 16| 6mm Hex Nuts
16| 8mm x 30mm Hex Bolts| |

HD-Ridez-HW-WB-TT298-Blow-Molding-Running-Boards-FIG1

PROCEDURE

  1. REMOVE CONTENTS FROM THE BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY. ASSISTANCE IS HIGHLY RECOMMENDED.
  2. Starting on the Passenger/Right side of the vehicle and remove the plastic plugs or hex bolts from the factory mounting location along the bottom of the body, (Figures 1 & 4).
  3. Select the Passenger/Right Front Mounting Bracket. Attach the Bracket to the front location with (2) 8mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers, (Figures 2 & 3). Do not tighten the hardware.
  4. Repeat Steps 2 & 3 to attach the (3) Rear Mounting Brackets, (Figures 4 & 5).
  5. Select the Passenger/Right P1 Running Board. Select (4) 6mm Bolt Plates. Insert the Bolt Plates into the channel in the bottom of the Running Board, (Figure 6).
  6. Lift the Running Board onto the (4) Mounting Brackets and line up the Bolt Plates into the slots. Attach the Running Board to the Mounting Brackets with (8) 6mm Flat Washers, (8) 6mm Lock Washers and (8) 6mm Hex Nuts, (Figure
    • Do not tighten the hardware.
  7. Level and adjust the Running Board and tighten all hardware.
  8. Repeat Steps 2—7 to attach the Driver/Left P1 Running Board.
  9. Do periodic inspections to the installation to make sure that all hardware is secure and tight.

To protect your investment, Do not use any type of polish or wax that may contain abrasives that could damage the finish. Use only mild soap to clean the Running Boards.

Installation

Passenger/Right Side Installation Pictured

HD-Ridez-HW-WB-TT298-Blow-Molding-Running-Boards-FIG2

HD-Ridez-HW-WB-TT298-Blow-Molding-Running-Boards-FIG3

Documents / Resources

| HD Ridez HW-WB-TT298 Blow Molding Running Boards [pdf] Instruction Manual
HW-WB-TT298 Blow Molding Running Boards, HW-WB-TT298, Blow Molding Running Boards, Molding Running Boards, Running Boards, Boards
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

HD Ridez User Manuals

Related Manuals