HD Ridez IB-227C Stainless Steel Running Board Side Step Bars Instruction Manual

June 1, 2024
HD Ridez

HD Ridez IB-227C Stainless Steel Running Board Side Step Bars

Product Specifications

  • Part Number: IB-227C&H
  • Fastener Size: 6mm, 8mm, 10mm, 12mm, 14mm
  • Tightening Torque (ft-lbs):
    • 6mm: 6-7
    • 8mm: 16-18
    • 10mm: 31-32
    • 12mm: 56-58
    • 14mm: 92-94

Product Usage Instructions

Step 1: Driver Side Front Mounting

Start installation from the driver side front of the vehicle. Locate the factory threaded studs located on the side of the inner body panel.

Step 2: Driver Front Mounting Bracket Installation

Select (1) Mounting Bracket. Attach the Mounting Bracket to the (2) Studs with (2) M8 Large Flat Washers, (2) M8 Lock Washers, and (2) M8 Hex Nuts. Do not fully tighten hardware at this time.

Step 3: Center & Rear Mounting

Move to the center & rear mounting location. Repeat Steps 1-2 to install the center & rear side mounting brackets. Do not fully tighten hardware at this time.

Step 4: Step Bar Installation

Attach the Step Bar to the sliders using (2) M8 Large Flat Washers, (2) M8 Nylon Lock Nuts, and (2) Carriage Bolts. Ensure all hardware is securely tightened.

Attention: Do periodic inspections to the installation to make sure that all hardware is secure and tight. Use mild soap/non-abrasive products for cleaning to protect your bars/boards.

Frequently Asked Questions

Q: Do I need any special tools for installation?

A: No special tools are required for installation. Basic hand tools should be sufficient.

Q: Can these step bars be installed on any vehicle?

A: These step bars are designed for specific vehicle models.
Please check compatibility before installation.

Q: How do I contact customer support for assistance?

A: For customer support, please email info@iboardauto.com or refer to the contact information provided in the manual.

PART#: IB-227C&H

READ INSTRUCTIONS CAREFULLY BEFORE START ING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED.

  • ROCKER PANEL MOUNT
  • NO DRILLING REQUIRED
Fastener Size Tightening Torque (ft-lbs) Required
6mm 6-7 X
8mm 16-18
10mm 31-32 X
12mm 56-58 X
14mm 92-94 X

PART LIST

HD-Ridez-IB-227C-Stainless-Steel-Running-Board-Side-Step-Bars-
FIG-2 HD-Ridez-IB-227C-
Stainless-Steel-Running-Board-Side-Step-Bars-FIG-3

INSTALLATION

STEP 1
Start installation from the driver side front of the vehicle. Locate the factory threaded studs located on the side of the inner body panel, (Fig 1).

STEP 2
Select (1) Mounting Bracket. Attach the Mounting Bracket to the (2) Studs with (2) M8 Large Flat Washers, (2) M8 Lock Washers and (2) M8 Hex Nuts, (Fig 2). Do not fully tighten hardware at this time.
Note: (6) Mounting Brackets are universal.

STEP 3
Move to the center & rear mounting location. Repeat Steps 1-2 to install the center & rear side mounting brackets. Do not fully tighten hardware at this time.

STEP 4
Once all (3) Driver side mounting brackets are installed, then proceed to the Step Bar installation. (Figs 3 & 4)

  1. Select (1) Slider and (2) M8X1.25-35mm Carriage Bolts;
  2. Install (2) M8X1.25-35mm Carriage Bolts in (1) Slider.
  3. Slide the Slider (with carriage bolts) to the Step Bar.
  4. Repeat to install the other (2) sliders to the step bar.
  5. Attach the Step Bar (with the Sliders) onto the installed mounting brackets. Position the Sliders to the installed brack-ets. Secure the Step Bar to the installed Brackets by using (6) M8 Large Flat Washers and (6) M8 Nylon Lock Nuts and (3) Sliders, (Fig 4). Do not fully tighten hardware at this time.
    Note: The Sliders are packed with the Step Bars.
    Level and adjust the Step Bar and fully tighten all hardware.
    Repeat Steps 1-4 for the other side Step Bar installation. The installation is completed!!!

HD-Ridez-IB-227C-Stainless-Steel-Running-Board-Side-Step-Bars-
FIG-6

Customer Support: info@iboardauto.com

Attention
Do periodic inspections to the installation to make sure that all hardware is secure and tight.
In order to protect your bars/boards, please use mild soap/non-abrasive products for cleaning only.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

HD Ridez User Manuals

Related Manuals