HD Ridez WB-NS050SD OE Style Mirror Polished Nerf Bars Running Boards Instruction Manual

June 1, 2024
HD Ridez

HD Ridez WB-NS050SD OE Style Mirror Polished Nerf Bars Running Boards

Specifications

  • Product Name: S6 Running Board
  • Compatibility: 04-15 & 17-24 Nissan Titan Crew Cab and 16-24 Titan XD Crew Cab
  • Part Numbers: WB-NS050SD (Driver/Left side) / WB-NS050BD (Passenger/Right side)

Product Usage Instructions

Parts List:

  • 1 Driver/Left side S6 Running Board
  • 1 Passenger/Right side S6 Running Board
  • 3 Driver/Left side Mounting Brackets
  • 3 Passenger/Right side Mounting Brackets
  • 12 8mm x 30mm Hex Bolts
  • 24 8mm x 24mm OD x 2mm Flat Washers
  • 18 8mm Nylon Lock Nuts
  • 12 8mm Lock Washers
  • 6 8mm x 35mm Double Bolt Plates

Installation Procedure:

  1. Remove contents from the box and verify all parts are present.
  2. Start installation at the front of the Driver/Left side of the vehicle.
  3. Locate factory threaded holes or studs on the inner body panel and remove any plastic plugs or insulation to access them.
  4. Install mounting brackets on the body panel using provided hardware.
  5. Attach the Running Board to the brackets using washers and nuts. Do not tighten hardware yet.
  6. Level and adjust the Running Board, then tighten all hardware securely.
  7. Repeat the process for the Passenger/Right side Running Board.
  8. Periodically inspect the installation to ensure all hardware remains secure.

Cleaning Instructions:

To protect your investment, avoid using polish or wax with abrasives that could damage the finish. Mild soap can be used for cleaning the Running Board.

FAQ

Q: Can I use this running board on other vehicle models?

A: No, this running board is specifically designed for 04-15 & 17-24 Nissan Titan Crew Cab and 16-24 Titan XD Crew Cab models.

Q: How often should I inspect the installation?

A: It is recommended to perform periodic inspections to ensure all hardware remains secure and tight. Check at least every few months or after driving on rough terrain.

S6 RUNNING BOARD
04-15 & 17-24 NISSAN TITAN CREW CAB AND 16-24 TITAN XD CREW CAB

PART#WB-NS050SD/WB-NS050BD

PARTS LIST

1 Driver/Left side S6 Running Board 12 8mm x 30mm Hex Bolts
1 Passenger/Right side S6 Running Board 24 8mm x 24mm OD x 2mm Flat Washers
3 Driver/Left side Mounting Brackets 18 8mm Nylon Lock Nuts
3 Passenger/Right side Mounting Brackets 12 8mm Lock Washers
6 8mm x 35mm Double Bolt Plates  

INSTALLATION INSTRUCTIONS

PROCEDURE:
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.

  1. Start installation at the front of the Driver/Left side of the vehicle and locate the factory threaded holes or stud located on the side of the inner body panel, (Figures 1 & 2). There are (4) mounting locations along the body panel. Bracket installation will use the 1st, 2nd and 4th mounting locations. NOTE: Remove the plastic plug or any insulation on the side panel to locate the threaded holes.

  2. Select (1) Driver/Left Mounting Bracket. Attach the Bracket to the mounting location with:
    a. Models with threaded stud: Attach Bracket to stud with (1) 8mm x 24mm Flat Washer and (1) 8mm Nylon Lock Nut. Next, use (1) 8mm Hex Bolt, (1) 8mm Lock Washer and (1) 8mm x 24mm Flat Washer to attach the Bracket to the threaded insert hole on the body panel,(Figure 3). Do not tighten hardware.
    b. Models without threaded stud: Attach Bracket to the upper threaded hole with (1) 8mm x 30mm Hex Bolt, (1) 8mm Lock Washer and (1) 8mm x 24mm Flat Washer. Attach Bracket to the lower threaded hole with (1) 8mm Hex Bolt, (1) 8mm Lock Washer and (1) 8mm x 24mm Flat Washer, (Figure 3). Do not tighten hardware.

  3. Repeat Steps 1 & 2 to install the center and rear Mounting Brackets.

  4. Select the Driver/Left S6 Running Board. Select (3) Double Bolt Plates. Insert the Bolt Plates into the channel in the bottom of the Running Board closest to the Brackets, (Figure 4). Lift the Running Board up and guide the studs through the Brackets. IMPORTANT: Do not slide, (front to back), the Running Board on the Brackets or damage to the finish may result.

  5. Attach the Running Board to the Brackets with (6) 8mm x 24mm Flat Washers and (6) 8mm Nylon Lock Nuts (Figure 5). Do not tighten hardware.

  6. Level and adjust the Running Board and tighten all hardware.

  7. Repeat Steps 1—6 to attach the Passenger/Right S6 Running Board.

  8. Do periodic inspections of the installation to make sure that all hardware is secure and tight.

To protect your investment: Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used to clean the Running Board.

Driver/Left Side Installation Pictured

Please select text to grab.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

HD Ridez User Manuals

Related Manuals