HD Ridez IA-N095H Pocket Drop Steps Armor Instruction Manual
- May 15, 2024
- HD Ridez
Table of Contents
HD Ridez IA-N095H Pocket Drop Steps Armor
BEFORE INSTALLATION
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMEND-ED. THANK YOU FOR CHOOSING OUR PRODUCT!
- ROCKER PANEL MOUNT
- DRILLING NOT REQUIRED
Torque Value
Fastener Size | Tightening Torque (ft-lbs) | Required |
---|---|---|
6mm | 6-7 | √ |
8mm | 16-18 | √ |
10mm | 31-32 | X |
12mm | 56-58 | X |
14mm | 92-94 | X |
Hardware Package A (For Brackets & Bars Installation)
Item| QTY| Description| Item| QTY| Description
1#| 12| M8 Hex Flange Nuts| 7#| 2| M6 Large Flat Washers
2#| 2| M8X1.25-25 Hex Bolts| 8#| 2| M6 Nylon Lock Nuts
3#| 14| M8 Large Flat Washers| 9#| 10| M8X1.25-20 T-Bolts
4#| 2| M8 Lock Washers| 10#| 10| M8 Plastic Washers
5#| 2| M8 Hex Nuts| 11#| 10| M8 Nylon Lock Nuts
6#| 2| M6X1-20 Square Head Bolts| | |
| ****
| | | | | | | | | |
Hardware Package B (For Step Pedals Installation)
Item| QTY| Description| Item| QTY| Description
1#| 24| M8X1.25-25 Hex Bolts| 3#| 24| M8 Lock Washers
2#| 24| M8 Large Flat Washers| | |
The instructions here is for your reference only. We strongly recommend the professional installer for the best result. We are not responsible for any damage caused by the installation.
STEP 1
Install (4) Pedals onto the step bars with (24) M8X1.25-25mm Hex Bolts, (24)
M8 Large Flat Washers and (24) M8 Lock Washers.
IMPORTANT: Don’t punch the pedal with any metal hummer within pedal installation, or the pedal will be damaged.
STEP 2
Start the installation from the driver side front of the vehicle, (Fig 1).
Attach (1) Driver Front Mounting Bracket (DFM/PCM), to the (2) factory studs
with (2) M8 Hex Flange Nuts, (Fig 2). Do not fully tighten hardware at this
time.
STEP 3
Move to the Driver Side Center Mounting Location, repeat STEP 2 to install the
Driver Center Mounting Bracket (DCM/PFM) to the (2) factory studs with (2) M8
Hex Flange Nuts. Do not fully tighten the hardware at this time.
STEP 4
Assemble (1) Driver Rear Mounting Bracket (DRM) and (1) Driver Rear Support
Bracket (DRS) with (1) M8X1.25-25mm Hex Bolt, (1) M8 Lock Washer, (2) M8 Flat
Washers and (1) M8 Hex Nut, (Fig 3). Repeat STEP 2 to install the driver-side
rear mounting bracket. Do not fully tighten hardware at this time.
STEP 5
Once all (3) brackets have been installed, select (5) M8X1.25-20mm T-Bolts,
thread (1) M8 Plastic Washer on each T-Bolt, (Fig 4). Install the (5)
M8X1.25-20mm T-Bolts with plastic washers in the slots on the assembled Driver
side step bar. Rotate the T-Bolts to 90 degree, thread down the M8 Plastic
Washers against the step bar (Fig 5).
NOTE: The Plastic Washer is designed to keep the T-Bolt in place to avoid falling into the tube during installation.
STEP 6
Attach the Assembled Driver Side Step Bar onto the Mounting Brackets with (5) M8 Plastic Washers, (5) M8X1.25-20mm T-Bolts, (5) M8 Large Flat Washers, (5) M8 Nylon Lock Nuts, (Fig 6). Do not fully tighten the hardware at this time.
NOTE: Driver’s Rear Mounting Bracket is located under the rear pedal. Slide (1) M6X1-20mm Square Head Bolt into the channel at the bottom of the rear pedal (Fig 7). And secure the Driver Rear Mounting Bracket to the pedal with (1) M6 Large Flat Washer and (1) M6 Nylon Lock Nut, (Fig 6). Do not fully tighten the hardware at this time.
STEP 7
Level and adjust the assembled Step Bar properly and tighten all hardware.
Move to the other side of the vehicle. Repeat Steps 2-6 for the other Side
Step Bar installation.
Attention Do periodic inspections to the installation to make sure that all hardware is secure and tight. To protect your bars/boards, please use mild soap/non-abrasive products for cleaning only.
- Customer Support: info@iarmorauto.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>