HD Ridez WB-DR179BD Drop Down Style Running Boards Side Step Instruction Manual

HD Ridez WB-DR179BD Drop Down Style Running Boards Side Step

Product Information

Specifications:

• Product Name: RS6 Overland Slider Drop Steps
• Compatibility: 09-18 Dodge Ram 1500 Quad Cab (Incl. 19-24 Ram 1500 Classic)
• Part Number: WB-DR179BD

Product Usage Instructions:

Parts List:

• 1 Driver/Left Tube
• 1 Passenger/Right Tube
• 4 Drop Steps
• 6 Driver Front/Passenger Rear Mounting Brackets
• 6 Passenger Front/Driver Rear Mounting Brackets
• 6 Driver Front/Passenger Rear Support Brackets
• 6 Passenger Front/Driver Rear Support Brackets
• 12 10mm x 30mm Hex Bolts
• 24 10mm x 20mm OD x 2mm Flat Washers
• 12 10mm Nylon Lock Nuts
• 8 8mm Triangle Double Bolt Plates

Installation Procedure:

1. Remove contents from the box and verify all parts are present.
2. Carefully read the instructions before starting the installation as drilling may be required.
3. Starting at the Driver/Left side-front of the vehicle, remove the sealing tape covering the factory holes in the side of the inner panel.
4. Thread an 8mm Plastic Retainer onto the threaded end and down tight against the body panel to prevent the Bolt/Nut Plate from falling into the body panel.
5. Attach the Driver/Left Bracket to the Bolt Plate using an 8mm Flat Washer, an 8mm Lock washer, and an 8mm Hex Nut.

Maintenance:
To protect your investment, do not use any polish or wax that may contain abrasives that could damage the finish. Mild soap can be used to clean the Overland Sliders.

Frequently Asked Questions (FAQ):

• Q: Are these drop steps compatible with other truck models?
  A: The RS6 Overland Slider Drop Steps are specifically designed for 09-18 Dodge Ram 1500 Quad Cab (Incl. 19-24 Ram 1500 Classic) models and may not be compatible with other trucks.

• Q: Do I need to drill holes for installation?
  A: Yes, drilling may be required for the installation of these drop steps. Please refer to the installation instructions for guidance.

• Q: Can I use abrasive cleaners on the product?
  A: It is not recommended to use any type of polish or wax that may contain abrasives as they could damage the finish. Mild soap is suggested for cleaning.

PARTS LIST

Washers
3| Passenger Front/Driver Rear Mounting Brackets| 12| 8mm Lock Washers
3| Driver Front/Passenger Rear Support Brackets| 6| 8mm Hex Nuts
3| Passenger Front/Driver Rear Support Brackets| 22| 8mm Nylon Lock Nuts
12| 10mm x 30mm Hex Bolts| 6| 8mm Plastic Retainers
24| 10mm x 20mm OD x 2mm Flat Washers| 12| 6mm x 25mm Hex Bolts
12| 10mm Nylon Lock Nuts| 24| 6mm x 22mm OD x 2mm Flat Washers
8| 8mm Triangle Double Bolt Plates| 12| 6mm Nylon Lock Nuts

OVERVIEW

INSTALLATION INSTRUCTION

PROCEDURE: REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. DRILLING MAY BE REQUIRED.

1. Starting at the Driver/Left side-front of the vehicle, remove the sealing tape covering the factory holes in the side of the inner panel, (Figure 1).

2. Determine the correct procedure to attach the Driver/Left side front Bracket for your model/year: Models without factory threaded inserts in body panel:

   • a. Select (1) 8mm Bolt/nut Plate, (Figure 2). Partially thread an 8mm Hex Bolt onto the threaded of the Nut Plate, (Figure 3). Thread the Hex Bolt in until it is flush with the welded nut. Use the Hex Bolt as a handle and insert the Bolt and Nut Plate into the oval hole, (Figure 4). Feed the threaded bolt on the Bolt Plate through one of the hex shaped factory holes.
     b. Thread (1) 8mm Plastic Retainer onto the threaded end and down tight against the body panel,(Figure 5). NOTE: The Plastic Retainer is designed to keep the Bolt/Nut Plate from falling into the body panel and to aid in Bracket installation.
     c. Select (1) Driver/Left Bracket, (Figure 6). Attach the Bracket to the threaded end of the Bolt Plate with (1) 8mm Flat Washer, (1) 8mm Lock washer and (1) 8mm Hex Nut, (Figure 6).
     IMPORTANT: Driver/Left Front Brackets are the same as the Passenger/Right Rear Bracket. Do not tighten hardware.
     d. Remove the 8mm Hex Bolt from the nut on the Bolt Plate from Step 2a. Rotate the Bolt on the Bolt Plate until the threaded nut lines up with the remaining hole in the Mounting Bracket and body panel, (Figure 7). Attach the Bracket to the threaded Nut Plate with (1) 8mm x 30mm Hex Bolt, (1) 8mm Lock Washer and (1) 8mm Flat Washer, (Figure 7). Do not tighten hardware.
     Models with factory threaded inserts:
     a. Attach the Driver/Left Mounting Bracket to the threaded inserts with (2) 8mm x 30mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washer, (Figures 8 & 9). Do not tighten hardware.

3. Select (1) Driver/Left Support Bracket. Attach the Bracket to the back of the pinch weld with (2) 6mm Hex Bolts, (4) 6mm Flat Washers and (2) 6mm Flange Nuts, (Figure 10). Do not tighten hardware. Attach the Support Bracket to the Mounting Bracket with (1) 8mm Hex Bolt, (2) 8mm Flat Washers and (1) 8mm Nylon Lock Nut, (Figure 11).
   IMPORTANT: 2009-12 models not equipped with factory holes will require drilling through the pinch weld to fully attach Bracket. Do not drill through pinch weld at this time, (see Step 7).

4. Move along the side of the body panel to the center mounting location, (Figure 12). Repeat Steps 1—3 to install (1) Passenger/Right Mounting Bracket and (1) Passenger/Right Support Bracket to the Driver/Left center mounting location.

5. Move to the rear location, (Figure 13). Repeat Steps 1—3 to attach (1) Passenger/Right Mounting Bracket and (1) Passenger/Right Support Bracket to the Driver/Left rear mounting location.

6. Select the Driver/Left Tube. Insert (2) 8mm Double Bolt Plates into the front (2) sets of (2) holes, (Figure 14). Attach (1) Drop Step to the (2) Double Bolt Plates with (4) 8mm x 22mm Flat Washers and (4) 8mm Nylon Lock Nuts, (Figure 15). Do not tighten hardware.

7. With assistance, line up the mounting tabs in the Driver/Left Tube to the rear faces of the Mounting Brackets. Secure the Tube to the Mounting Brackets with (6) 10mm Hex Bolts, (12) 10mm Flat Washers and (6) 10mm Nylon Lock Nuts, (Figure 16). Do not tighten hardware.

8. Properly level and adjust the Overland Slider and fully tighten all hardware.
   2009-12 models requiring drilling through pinch trim:

   • a. Level the Overland Slider to the vehicle. Make sure all (3) Brackets are tight against the bottom of the body panel and tighten all mounting hardware.

   • b. Mark the location of the slots onto the pinch weld.

   • c. Drill (2) 1/4” holes through the pinch weld for each Bracket.
     IMPORTANT: Do not drill too close to the bottom edge of the pinch weld. Drill the holes in the center of the marked slots.

   • d. Repeat Step 3 to attach the Brackets to the drilled holes in the pinch weld. Check for level then fully tighten all hardware.

9. Repeat Steps 1—8 to attach the Passenger/Right Overland Slider.

10. Do periodic inspections to the installation to make sure that all hardware is secure and tight.

To protect your investment, Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used to clean the Overland Sliders.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>