HD Ridez WB-DN179LMD Wheel to Wheel Drop Down Style Running Boards Side Step Installation Guide

HD Ridez WB-DN179LMD Wheel to Wheel Drop Down Style Running Boards Side

Step

Specifications:

• Product Name: NB1 Wheel to Wheel Running Boards
• Compatible with: 09-18 Dodge Ram 1500 Quad Cab 6.5ft Bed, including 19-24 Ram 1500 Classic
• Part Number: WB-DN179LMD
• Material: Metal (Bolts, Washers, Nuts), Plastic (Retainers)

Product Usage Instructions

Parts List:

• 1 Driver/Left Running Board
• 1 Passenger/Right Running Board

Installation Procedure:

1. Remove contents from the box and verify all parts are present.
2. Read instructions carefully before starting installation. Note: Drilling may be required.
3. Starting at the Driver/Left side-front of the vehicle, remove the sealing tape covering the factory holes in the side of the inner panel.

Maintenance:

To protect your investment, do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used to clean the running boards.

FAQ

Q: Are these running boards compatible with other truck models?

A: These running boards are specifically designed for use with 09-18 Dodge Ram 1500 Quad Cab 6.5ft Bed, including 19-24 Ram 1500 Classic. Compatibility with other models is not guaranteed.

Q: Do I need any special tools for installation?

A: Basic tools like a drill, wrenches, and screwdrivers may be required for installation. Please refer to the instruction manual for a detailed list of tools needed.

NB1 WHEEL TO WHEEL RUNNING BOARDS 09-18 DODGE RAM 1500 QUAD CAB 6.5FT BED INCL. 19-24 RAM 1500 CLASSIC
PART# WB-DN179LMD

PARTS LIST

INSTALLATION INSTRUCTIONS

PROCEDURE: REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. DRILLING MAY BE REQUIRED.\

1. Starting at the Driver/Left side-front of the vehicle, remove the sealing tape covering the factory holes in the side of the inner panel, (Figure 1).

2. Determine the correct procedure to attach the Driver/Left side front Bracket for your model/year: Models without factory threaded inserts in body panel:

   • a. Select (1) 8mm Bolt/nut Plate, (Figure 2). Partially thread an 8mm Hex Bolt onto the threaded of the Nut Plate, (Figure 3). Thread the Hex Bolt in until it is flush with the welded nut. Use the Hex Bolt as a handle and insert the Bolt and Nut Plate into the oval hole, (Figure 4). Feed the threaded bolt on the Bolt Plate through one of the hex shaped factory holes.
   • b. Thread (1) 8mm Plastic Retainer onto the threaded end and down tight against the body panel,(Figure 5). NOTE: The Plastic Retainer is designed to keep the Bolt/Nut Plate from falling into the body panel and to aid in Bracket installation.
   • c. Select (1) Driver/Left Bracket, (Figure 6). Attach the Bracket to the threaded end of the Bolt Plate with (1) 8mm Flat Washer, (1) 8mm Lock washer and (1) 8mm Hex Nut, (Figure 6). IMPORTANT: Driver/Left Front and Center Brackets are the same as the Passenger/Right Rear Bracket. Do not tighten hardware.
   • d. Remove the 8mm Hex Bolt from the nut on the Bolt Plate from Step 2a. Rotate the Bolt on the Bolt Plate until the threaded nut lines up with the remaining hole in the Mounting Bracket and body panel, (Figure 7). Attach the Bracket to the threaded Nut Plate with (1) 8mm x 30mm Hex Bolt, (1) 8mm Lock Washer and (1) 8mm Flat Washer, (Figure 7). Do not tighten hardware.
     Models with factory threaded inserts:
     a. Attach the Driver/Left Mounting Bracket to the threaded inserts with (2) 8mm x 30mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washer, (Figures 8 & 9). Do not tighten hardware.

3. Select (1) Driver/Left Support Bracket. Attach the Bracket to the back of the pinch weld with (2) 6mm Hex Bolts, (4) 6mm Flat Washers and (2) 6mm Flange Nuts, (Figure 10). Do not tighten hardware. Attach the Support Bracket to the Mounting Bracket with (1) 8mm Hex Bolt, (2) 8mm Flat Washers and (1) 8mm Nylon Lock Nut, (Figure 11).
   IMPORTANT: 2009-12 models not equipped with factory holes will require drilling through the pinch weld to fully attach Bracket. Do not drill through pinch weld at this time, (see Step 7).

4. Move along the side of the body panel to the center mounting location, (Figure 12). Repeat Steps 1—3 to install (1) Driver/Left Mounting Bracket and (1) Driver/Left Support Bracket to the center mounting location.

5. Move to the rear location, (Figure 13). Repeat Steps 1—3 to attach (1) Passenger/Right Mounting Bracket and (1) Passenger/Right Support Bracket to the Driver/Left rear mounting location.

6. Select the Driver/Left Running Board. Attach the Running Board to the rear faces on the Mounting Brackets with (6) 10mm Hex Bolts, (12) 10mm Flat Washers and (6) 10mm Nylon Lock Nuts, (Figure 14). Do not tighten hardware.

7. Properly level and adjust the Running Board and fully tighten all hardware.
   2009-12 models requiring drilling through pinch trim:

   • a. Level the Running Board to the vehicle. Make sure all (3) Brackets are tight against the bottom of the body panel and tighten all mounting hardware.
   • b. Mark the location of the slots onto the pinch weld.
   • c. Drill (2) 1/4” holes through the pinch weld for each Bracket. IMPORTANT: Do not drill too close to the bottom edge of the pinch weld. Drill the holes in the center of the marked slots.
   • d. Repeat Step 3 to attach the Brackets to the drilled holes in the pinch weld. Check for level then fully tighten all hardware.

8. Repeat Steps 1—7 to attach the Passenger/Right Running Board.

9. Do periodic inspections to the installation to make sure that all hardware is secure and tight.

To protect your investment, Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used to clean the Running Boards.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>