RODE NT1-A Diaphragm Cardioid Condenser Microphone User Guide
- June 1, 2024
- Rode
Table of Contents
RODE NT1-A Diaphragm Cardioid Condenser Microphone
Product Information
Specifications
- Brand: RODE
- Model: NT1-A
- Power Requirement: 48Vdc, 6mA
- Compliance: FCC Part 15, CAN ICES-003 (B) / NMB-003 (B)
- Company Address: 2745 Raymond Ave, Signal Hill CA 90755, USA
- Telephone Number: +1 562 364 7400
Product Usage Instructions
- Attach the pop filter to the shock mount by screwing it into the mounting thread with the ‘L’-shaped bracket until securely in place.
- Place the NT1-A microphone in the shock mount and loosely screw it into the holder’s base by turning clockwise.
- Adjust the height, tilt, and swivel of the pop filter to your preference.
- Attach the other mounting thread to your studio arm, microphone stand, or similar fixture.
- Connect one end of the provided XLR cable to the base of the NT1-A and the other end to your interface, mixer, or similar device.
- Activate 48V phantom power (P48) on your device and start recording!
FAQ
Q: What should I do if the equipment causes interference?
A: If the equipment causes interference to radio or television reception,
try one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a different circuit from the receiver.
- Consult the dealer or a radio/TV technician for assistance.
Q: How can I prevent hearing damage while using the product?
A: To prevent possible hearing damage, avoid listening at high volume
levels for extended periods.
NT1-A QUICK START GUIDE
- To attach the pop filter to the shock mount, screw it into the mounting thread with the ‘L’-shaped bracket until securely in place
- Place the NT1-A inside the shock mount and rotate the microphone clockwise to screw it loosely into the base of the mount
- Adjust the orientation of the microphone so that the gold dot faces the pop filter, and then tighten the ring beneath the mount while holding the microphone to secure it in place
- Adjust the height, tilt and swivel of the pop filter to taste
- Attach the other mounting thread to your studio arm, microphone stand or similar mount
- Connect one end of the included XLR cable to the base of the NT1-A and the other end to your interface, mixer or similar device
- Enable 48V phantom power (P48) on your device and start recording!
North America
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Please note that changes or modifications of this product is not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAN ICES-003 (B) / NMB-003 (B)
Company Name : RODE LLC
Address: 2745 Raymond Ave, Signal Hill CA 90755, USA
Telephone Number: +1 562 364 7400
USA
SOUTH KOREA
ID: R-R-R72-NT1-A
Company Name: RØDE Microphones Model: NT1-A
Country of Origin: Australia
POWER
48Vdc 6mA
To prevent possible hearing damage, do not listen at high volume levels for long periods.
RØDE Microphones:
107 Carnarvon St, Silverwater NSW 2128, Australia
Authorised UK Representative:
RØDE UK, Unit A, 23-25 Sunbeam Rd, London
NW10 6JP, United Kingdom
Authorised EU Representative:
RØDE EU, Neukirchner Str. 18, 65510 Hünstetten, Germany
SCAN FOR MORE INFO
View the user guide to learn more rode.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>