MINKA LAVERY 4588-672 Caprio 8-Light Natural Brushed Brass Pendant Instruction Manual

MINKA LAVERY 4588-672 Caprio 8-Light Natural Brushed Brass Pendant

Product Information

The Fixture #4588-672 is a decorative lighting fixture that features a crystal ball, fabric shade, and candelabra base bulbs.
It comes with all the necessary parts for installation, including mounting hardware, rods, circular strap, canopy, decorative nuts, quick link, and support cable. The fixture is designed to be mounted on a junction box and can be adjusted for desiredheight

Product Usage Instructions

1. Before starting the installation, ensure that the power is shut off at the fuse box or circuit breaker.
2. Remove the old fixture and its mounting hardware.
3. Carefully unpack the new fixture and lay out all the parts in a clean area.
4. Attach the crystal ball onto the tube.
5. Install the fabric shade on the arms using metal nuts and place the decorative ring on the fabric shade.
6. Determine the desired height and thread the rods together. Screw the loop to one of the rods and pass the wires through each rod as you assemble. Attach the bottom end of the rod into the coupling.
7. Attach the quick link to the loop on the canopy. Carefully feed the wire through the loop, quick link, and another loop.
8. Attach the circular strap to the junction box using the provided screws. Ensure that the side marked GND faces out. Adjust the mounting screw if necessary.
9. Use the support cable to hold the weight of the fixture while wiring. Align the fixture with the circular strap and attach the hook on the end of the support cable into a slot on the circular strap. Allow the support cable to support the weight of the fixture  while wiring.
10. Connect the electrical wires according to the wiring diagram in Figure 2. Make sure that all wire connectors are secured. If your junction box has a ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the circular strap using the green screw provided.
11. Tuck the wire connectors neatly into the junction box.
12. Raise the fixture over the mounting screws and secure it with decorative nuts.
13. Place candle covers over the sockets, then place tube covers over the candle covers. Install up to 8 candelabra base bulbs (up to 60 watts each) or CFL or LED equivalent bulbs (not included) in accordance with the fixture’s specification. Do not exceed the maximum wattage rating.
14. Attach the leaf finial with the coupling.
15. Your installation is now complete. Turn on the power supply of the junction box to test the fixture.

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.

ASSEMBLY THE FIXTURE (FIG. 1 &FIG.3)

1. Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts necessary for installation.

3. Attach crystal ball (T) onto tube (S).

4. Install fabric shade (M) on arms (R) using metal nuts (N) and place decorative ring (L）on fabric shade (M).

5. Determine the desired height and thread rods (G1 and G2) together. Screw loop (I1) to the rod (G1). Pass the wires carefully through each rod as you assemble. Attach the bottom end of rod into the coupling (J).

6. Attach quick link (H) to loop (I2) on canopy (D). Carefully feed the wire through loop (I1), quick link (H), and loop (I2). Attach circular strap (B) to the junction box using the junction box screws (C). The side of the circular strap (B) marked “GND” must face out. Mounting screw can be adjustable if necessary.

7. The support cable is provided to support the weight of the fixture while wiring. Align the fixture to circular strap (B) and attach hook on the end of support cable (E) into a slot located on circular strap (B). Carefully allow the support cable (E) to support the weight of the fixture while wiring.
   CONNECTING THE WIRES (FIG. 2)

8. Connect the electrical wires as shown in figure 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the circular strap (B) using the green screw provided.

9. Tuck the wire connectors neatly into the junction box.
   COMPLETING THE INSTALLATION (Fig. 1)

10. Raise the fixture over the mounting screws (A) and secure with decorative nuts (F).

11. Place candle covers (Q) over sockets (V), then place tube covers (K) over candle covers (Q). Install (8) eight candelabra base bulbs (X) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification—DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).

12. Attached leaf finial (O) with coupling (P).

The leaves on the lamp body can be manually adjusted to change their shape.
Your installation is now complete. Turn on the power supply of the junction box to test the fixture.
Note : Illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

FEATURES

Hardware Bag:

• A. Mounting Screw*2
• B. Circular Strap*1
• C. Screw*2
• D. Canopy*1
• F. Decorative Nuts *2
• H. Quick Link*1
• 1. Loop*2
• AA. Hex Nuts *2

Hardware Bag

• G1. ROD 6″*1
• G2. ROD 12″*3

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>