HD Ridez WB-DN208SMD Wheel to Wheel Drop Down Style Running Boards Side Step Installation Guide

HD Ridez WB-DN208SMD Wheel to Wheel Drop Down Style Running Boards Side

Step

Product Information

Specifications:

• Product Name: NB1 Wheel to Wheel Running Boards
• Compatibility: 2009-2018 Dodge Ram 1500 Crew Cab 5.5ft Bed (Including 2019-2024 Ram 1500 Classic)
• Part Number: WB-DN208SMD

Product Usage Instructions

Installation Instructions:

1. Remove contents from the box and verify all parts are present.
2. Read instructions carefully before starting the installation as drilling may be required.
3. Starting at the passenger side-front of the vehicle, follow the steps below:
4. Remove sealing tape covering factory holes in the side inner panel.
5. Thread an 8mm Plastic Retainer onto the threaded end against the body panel.
6. Attach the Driver/Left Bracket to the Bolt Plate with a Flat Washer, Lock Washer, and Hex Nut. Do not tighten hardware yet.
7. Rotate the Bolt on the Bolt Plate to align with the remaining hole in the Mounting Bracket and body panel. Attach with a Hex Bolt, Lock Washer, and Flat Washer. Do not tighten hardware.
8. For models with factory threaded inserts, follow these additional steps:
9. Attach the Driver/Left Front Bracket to the threaded inserts with Hex Bolts, Lock Washers, and Flat Washers. Do not tighten hardware.
10. Move along the side of the body panel to the center mounting location and repeat the installation steps for the center mounting location.

Frequently Asked Questions

Q: Are these running boards compatible with other vehicle models?

A: These running boards are specifically designed for 2009-2018 Dodge Ram 1500 Crew Cab 5.5ft Bed (Including 2019-2024 Ram 1500 Classic) and may not be compatible with other models.

Q: Is professional installation recommended?

A: While it is possible to install these running boards yourself, professional installation is recommended, especially if you are not experienced with drilling and mounting automotive accessories.

Q: Do I need any special tools for installation?

A: Basic tools like a drill, wrenches, and screwdrivers are required for installation. Refer to the user manual for a detailed list of tools needed.

NB1 WHEEL TO WHEEL RUNNING BOARDS 2009-2018 DODGE RAM 1500 CREW CAB 5.5FT BED (INCL. 19-24 RAM 1500 CLASSIC) PART# WB-DN208SMD

PARTS LIST

Lock Washers
3| Passenger/Right Front, Driver/Left Center, Rear Mounting Bracket| 6| 8mm Hex Nuts
3| Driver/Left Front, Passenger/Right Center, Rear Support Bracket| 6| 8mm Nylon Lock Nuts
3| Passenger/Right Front, Driver/Left Center, Rear Support Bracket| 6| 8mm Plastic Retainers
12| 10mm x 30mm Hex Bolts| 12| 6mm x 25mm Hex Bolts
24| 10mm x 20mm OD x 2mm Flat Washers| 24| 6mm x 22mm OD x 2mm Flat Washers
12| 10mm Nylon Lock Nuts| 12| 6mm Nylon Lock Nuts
6| 8mm Bolt Plates|  |

INSTALLATION INSTRUCTIONS

PROCEDURE: REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. DRILLING MAY BE REQUIRED.

1. Starting at the passenger side-front of the vehicle, remove the sealing tape covering the factory holes in the side of the inner panel, (Figure 1).

2. Determine the correct procedure to attach the passenger side front Bracket for your model/year: Models without factory threaded inserts in body panel:

   • a. Select (1) 8mm Bolt/nut Plate, (Figure 2). Partially thread an 8mm Hex Bolt onto the threaded of the Nut Plate, (Figure 3). Thread the Hex Bolt in until it is flush with the welded nut. Use the Hex Bolt as a handle and insert the Bolt and Nut Plate into the oval hole, (Figure 4). Feed the threaded bolt on the Bolt Plate through one of the hex shaped factory holes.
   • b. Thread (1) 8mm Plastic Retainer onto the threaded end and down tight against the body panel,(Figure 5). NOTE: The Plastic Retainer is designed to keep the Bolt/Nut Plate from falling into the body panel and to aid in Bracket installation.
   • c. Select (1) Driver/Left Bracket, (Figure 6). Attach the Bracket to the threaded end of the Bolt Plate with (1) 8mm Flat Washer, (1) 8mm Lock washer and (1) 8mm Hex Nut, (Figure 6). IMPORTANT: Driver/Left Front Bracket is the same as the Passenger/right Center and Rear Brackets. Do not tighten hardware.
   • d. Remove the 8mm Hex Bolt from the nut on the Bolt Plate from Step 2a. Rotate the Bolt on the Bolt Plate until the threaded nut lines up with the remaining hole in the Mounting Bracket and body panel, (Figure 7). Attach the Bracket to the threaded Nut Plate with (1) 8mm x 30mm Hex Bolt, (1) 8mm Lock Washer and (1) 8mm Flat Washer, (Figure 7). Do not tighten hardware.
     Models with factory threaded inserts:
     a. Attach the Driver/Left Front Bracket to the threaded inserts with (2) 8mm x 30mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washer, (Figures 8 & 9). Do not tighten hardware.

3. Select (1) Driver/Left Support Bracket. Attach the Bracket to the back of the pinch weld with (2) 6mm Hex Bolts, (4) 6mm Flat Washers and (2) 6mm Flange Nuts, (Figure 10). Do not tighten hardware. Attach the Support Bracket to the Mounting Bracket with

   • (1) 8mm Hex Bolt, (2) 8mm Flat Washers and
   • (1) 8mm Nylon Lock Nut, (Figure 11). IMPORTANT: 2009-12 models not equipped with factory holes will require drilling through the pinch weld to fully attach Bracket. Do not drill through pinch weld at this time, (see Step 7).

4. Move along the side of the body panel to the center mounting location, (Figure 12). Repeat Steps 1—3 to install (1) Driver/Left Mounting Bracket and (1) Driver/Left Support Bracket to the center mounting location.

5. Move to the rear location, (Figure 13). Repeat Steps 1—3 to attach (1) Driver/Left Mounting Bracket and (1) Driver/Left Support Bracket to the Driver/Left rear mounting location.

6. Select the Driver/Left Running Board. Attach the Running Board to the rear faces on the Mounting Brackets with (6) 10mm Hex Bolts, (12) 10mm Flat Washers and (6) 10mm Nylon Lock Nuts, (Figure 14). Do not tighten hardware.

7. Properly level and adjust the Running Board and fully tighten all hardware.
   2009-12 models requiring drilling through pinch trim:

   • a. Level the Running Board to the vehicle. Make sure all (3) Brackets are tight against the bottom of the body panel and tighten all mounting hardware.
   • b. Mark the location of the slots onto the pinch weld.
   • c. Drill (2) 1/4” holes through the pinch weld for each Bracket. IMPORTANT: Do not drill too close to the bottom edge of the pinch weld. Drill the holes in the center of the marked slots.
   • d. Repeat Step 3 to attach the Brackets to the drilled holes in the pinch weld. Check for level then fully tighten all hardware.

8. Repeat Steps 1—7 to attach the Passenger/Right Running Board.

9. Do periodic inspections to the installation to make sure that all hardware is secure and tight.

To protect your investment, Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used to clean the Running Boards.

Driver/Left Side Installation Pictured

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>