moni B3 Baby Crib Kalinihata User Manual
- June 1, 2024
- MONI
Table of Contents
moni B3 Baby Crib Kalinihata
Product Information
Specifications:
- Manufacturer: Moni
- Model: Baby Crib Kalinihta Item B3
- Compliance: European Directive 2001/98/EC, EN 1130:2019
Product Usage Instructions
Assembly Instructions
- Place the mattress with the soft side up in the crib. Secure the mattress to the base (refer to Figure 18).
- Attach the mosquito net – Secure the mosquito net to the side of the crib with snap-button closure.
Maintenance and Cleaning Instructions
Manufactured for Moni in PRC, Manufacturer and Importer: Moni Trade Ltd. Address: Bulgaria, Sofia, Trebich, 1 Dolo Str., Phone number: 003592/936 07 90, Website: www.moni.bg
FAQ
Q: What safety standards does the product comply with?
A: The product is manufactured in accordance with European Directive 2001/98/EC on General Product Safety, the Consumer Protection Act, and European Standard EN 1130:2019.
IMPORTANT! READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
This product is manufactured in accordance with the requirements of the European Directive 2001/98/EC on General Product Safety, the Consumer Prorection Act and the European Standard EN 1130: 2019.
IMPORTANT! READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
WARNING
- Do not use this product without reading the instructions for use first.
- Stop using the product as soon as the child can sit or kneel or pull itself up.
- Placing additional items in the product may cause suffocation.
- Do not place the product close to another product, which could present a danger of suffocation or strangulation, e.g. strings, blind/curtain cords, etc.
- Do not use more than one mattress in the product.
- The product should be placed on a horizontal floor.
- The young children should not be allowed to play unsupervised in the vicinity of the crib.
- The crib should be locked in the fixed position when the child is left unattended.
- All assembly fittings should always be tightened properly and that care should be taken that no screws are loose, because a child could trap parts of the body or clothing (e.g. strings, necklaces, ribbons for babies’ dummies, etc.) which would pose a risk of strangulation. Perform routine checks to make sure there are no loose, damaged or missing parts.
- The maximum internal size of the crib the mattress is intended for is 900/590 mm. The length and width shall be such that the maximum gap between the mattress and sides and ends does not exceed 2,5 cm.
- The product shall be kept away from burning cigarettes, open fires and other sources of strong heat, such as electric bar fires and gas fires.
- The base of the crib can be tilted up to 30° to prevent any discomfort and danger of suffocation of the child.
- DO NOT use the crib if any parts are missing, damaged or broken. Contact MONI TRADE for replacement parts and instructional literature, if needed. DO NOT substitute parts.
- WARNING!Only use the mattress sold with this crib, do not add a second mattress on this one, suffocation hazards!
- Do not make any changes or improvements to the design of the crib, as this may damage the crib and risk injury to the child.
ASSEMBLY INSTRUCTIONS
IMPORTANT! The diagrams and figures in this instruction are illustrative and indicative only. Check the securing of the fixation after each operation.
COMPONENTS – ILLUSTRATION A:
- Crib basket;
- Textile shelf for accessories;
- Crib mattress;
- Support crib tubes (2pcs);
- Plastic joint (2pcs);
- Side frames (legs) – 4pcs;
- Support tubes (4 pcs);
- Bolts (4 pcs).
ASSEMBLY OF THE STRUCTURE – ILLUSTRATION B:
ATTENTION! Follow exactly the instructions and sequence for assembling the product, described in the text and illustrations attached to the instructions.
- Assembling the side frames (legs) of the crib: Take a set – one plastic joint and two side frames (legs) as shown in Figure 1. Insert the both sides of the frames into the holes of the plastic connector and fix them in the direction of the arrow, as indicated in figure 2. The spring pin will snap into place once it is securely fastened on both sides (see figure 3). The same operation is performed to assemble the other set of side legs.
- Attaching a fabric basket to the legs of the crib: Take two support tubes and thread them through the holes in the fabric basket (see figure 4). Attach the fabric basket frame to the crib legs by securing each side of the frame in the indicated bottom holes using bolts (see figures 5, 6, 7 and 8). In the same way, fix the other two support tubes by fixing them in the upper holes of the legs of the crib through bolts (see figures 9, 10, 11 and 12).
- Installing the crib basket: Place the two support frames into the holes of the crib basket (see figure 13), then install the crib basket support frame to the plastic joint as shown in figures 14, 15, 16 and 17 Place the mattress in the crib with the soft side up. Attach the mattress to the base (see figure 18).
- Placing the mosquito net – The mosquito net is fixed with tic-tac buttons on the side of the bed.
INSTRUCTIONS FOR MAINTENANCE AND CLEANING
Clean the plastic or metal parts of the product with a soft cotton cloth or sponge moistened with water or a mild detergent. Do not use bleach, agressive detergents or abrasive products to clean the product. All textile parts and fabrics should be washed only by hand, following the instructions on the label. After cleaning, allow the crib to dry well before using it. Do not fold or remove the crib before it is completely dry. Do not expose the product to direct sunlight for extended periods of time and to extreme temperatures that may change color and damage exposed parts. After prolonged exposure to high temperatures, wait a few minutes before placing the child in it. Do not place objects in or on the product to avoid damaging the structure and / or upholstery. Store the product in a clean and dry place.
Manufactured for Moni in PRC,
- Manufacturer and Importer: Moni Trade Ltd.
- Address: Bulgaria, Sofia, Trebich, 1 Dolo Str.,
- Phone number: 003592/936 07 90,
- Website: www.moni.bg