Quality Heating QH-HH Series Infrared Panel User Manual

Quality Heating QH-HH Series Infrared Panel

Specifications

• Product: QH-HH Series Infrared Panel
• Heating Element: Infrared
• Heating Method: Radiant Heat

The QH-HH Series Infrared Panel is designed to provide efficient and comfortable heating using radiant heat technology. It is important to follow the instructions carefully to ensure safe and effective use of the product.

Usage Instructions

Warnings & Precautions

Before using the device, familiarize yourself with the following symbols and warnings:

• [Explain each symbol and its meaning]

Safety Guidelines

It is crucial to read the manual thoroughly before operating the device. Keep the manual accessible for reference at all times.
Failure to adhere to safety warnings and instructions may result in electric shocks, fire, or serious injury.

Key Safety Points

• [List important safety guidelines]

Installation Instructions

Ensure the panel is mounted at a height of over 1.8 meters.
Refer to the installation section for specific tips based on the series purchased.

Additional Safety Notes

• [Provide additional safety precautions]

FAQ

Q: What should I do if the surface temperature becomes too hot?

A: If the surface temperature is too high, ensure proper ventilation and avoid direct contact with the heated surface.

Q: Can children operate the device?

A: Children aged 8 and above can use the device under supervision and with proper instructions on safe usage.

Q: Where should sensors be placed for optimal performance?

A: Sensors with temperature detection should not be within 130 degrees of the ceiling heating panel’s radiation range for accurate temperature readings.

Warning & Precautions

Symbols

• Read this manual carefully before using the device.
• Always keep the manual in the immediate vicinity of the device or the place of use! Read all safety warnings and all instructions.
• Failure to follow the warnings and instructions may result in electric shock, fire, and/or serious injury. Save all warnings and instructions for future reference.
• Warning! This series must be mounted above 1.8 meters high!
• Check which series you purchased and install according to the tips in the installation section!
• Warning! This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. to understand. Children are not allowed to play with the device. Cleaning and user maintenance shall not be carried out by children without supervision.
• Warning! Children under 8 years of age should be kept away unless continuously supervised. This applies to children from 0 years to 8 years.
• Only turn the device on/off if the panel is positioned or installed as intended. Children under 8 years of age are not allowed to connect or service the panel.
• Warning! Do not use the device in small rooms if persons are present who cannot leave the room independently and who are not under constant supervision.
• Warning! Temperature sensing sensors, or temperature controllers, should not be placed within the 130-degree radiation range of the ceiling heating plate, otherwise, it will affect the actual temperature sensing.
• Warning! Some parts of this product may become very hot and this may cause burns and fire. Particular attention should be paid to children and vulnerable people present.
• It is dangerous to place the installation close to curtains and other flammable substances and materials.
• To avoid the possibility of burns, the following people should be much more careful when using the infrared panel: babies and children, people with sensitive skin, the old, the sick, drunk people, and people who have used sleeping pills.
• Remove the protective film (on the front) before use.
• Make sure the operating voltage is between 220-240V, 50Hz, and the power supply is strictly by IEC, left is neutral wire right is power feeding wire, and also well grounded
• The devices consume more power than small devices, therefore a separate 5A socket is required.
• Do not use the device in potentially explosive areas.
• Do not use the device in an aggressive atmosphere.
• Place the device in an upright and stable position.
• Allow the device to dry after wet cleaning. Do not use the device when it is wet.
• Do not use the device with wet hands.
• Do not expose the device to direct spraying water.
• Never insert objects or limbs into the device.
• Do not cover or transport the device during use.
• Do not sit on the device.
• This device is not a toy! Keep away from children and animals.
• Do not leave the device unattended during use.
• Check accessories and connecting parts for possible damage before each use of the device. Never use the device if it has defective parts.
• Make sure that all electrical cables outside the appliance are protected from damage (e.g. caused by animals). Never use the device if electrical cables or the power connection are damaged!
• The electrical connection must correspond to the specifications in the Technical data chapter.
• Plug the mains plug into a properly secured socket.
• Do not use the device if the socket, cable, or plug is overloaded.
• Consider the device’s power consumption, cable length, and intended use when choosing power cord extensions. Unwind extension cables completely. To avoid electrical overload.
• Before maintenance, care, or repair work on the device, remove the plug from the socket. Hold the plug firmly.
• Switch off the appliance and unplug it from the socket when the appliance is not in use.
• Never use the device if the plug or power cord is damaged. If the power cord is damaged, it must be replaced by the manufacturer, service agent, or similarly qualified persons to avoid a hazard.
• Defective power cables pose a serious health risk.
• When installing the device, observe the minimum distances to walls and other objects as well as the storage and operating conditions stated in the Technical data chapter.
• Never drill into the heater.
• Do not use the device near curtains.
• Do not place the device on flammable ground.
• Do not transport the device during use.
• Do not touch the surface while the appliance is operating to avoid burns.
• Allow the device to cool down before transport and/or maintenance work.
• Do not use this appliance near bathtubs, shower trays, swimming pools, or other water containers. The danger of electric shock!
• The device should be positioned so that the switches and controllers cannot be touched by a person in a bathtub or shower.
• Do not use this device in a daycare center or bathroom. (Only for Sweden)

Characteristics

• The device is designed as an efficient, comfortable, and healthy heating system for any household use
• The device reduces air circulation and helps maintain a clean, quiet, dust-free environment.
• A wide range of devices is available in different sizes, finishes, and colors.

Technical information

Product information

Model

number

| Size (mm)| Power (W)| Voltage/frequency| Current (A)
---|---|---|---|---
HH0606| 63063021| 450W| *** 230V/50Hz| 1.7A
HH1006| 103063021| 700W| 3A
HH1206| 1230630*21| 900W| 3.9A

Package contents

Tips:

1. E and F are for wall mounting only. G, H, I, and J are for ceiling mounting only.
2. G and H are used on concrete ceilings, while H, I, and J are used on plasterboard ceilings.

Device structure

1. Heating low
2. Aluminum frame
3. Insulation layer
4. Aluminum foil cloth or coated steel sheet
5. Mounting holes

Installation

a. Installation on concrete ceilings

1. Step 1: Measure and mark the correct hole distances on the ceiling where you want to install the panel.
2. Step 2: Drill four 10mm holes at the marked positions.
   • Warning! Too large a drill diameter is strictly prohibited! This can lead to incorrect installation of the panel.
3. Step 3: Insert the metal expansion tubes (C) into the drilled holes.
4. Step 4: Insert the Screws (H) through the holes in the Panel (A) and then tighten them into the metal expansion tubes (G).

Warning! Tighten the screws firmly until there is no more movement. This is very important for safety.

b. Plasterboard ceiling installation

1. Step 1: Measure and mark the correct distances from the panel to the ceiling where you want to install the panel.
   • Warning!
   • Please note that the toggle plugs (I) are designed for plasterboard and wooden ceilings with a thickness between 9mm and 18mm. It is prohibited to use these toggle plugs with a ceiling thickness below 9mm.
   • For wooden ceilings with a thickness of more than 18mm, you can consider using metal expansion tubes (G) or your own carpentry nails, making sure that the carpentry nails have a size of M5*40mm or larger.
2. Step 2: Drill four 18mm holes at the marked positions.
   • Warning! Too large a drill diameter is strictly prohibited! This can lead to incorrect installation of the panel.
3. Step 3: Insert the Screws (H) through the panel holes (A), washers (J), and toggle plugs (I) into the pre-drilled holes.
4. Step 4: Tighten the screws.

Problem solutions

2.  In a low-temperature environment.

| 1.  Install a voltage regulator

2.  It is a normal phenomenon.

Don’t worry about it.

Maintenance and Service

Required actions to start maintenance

Warning of electrical voltage.

• Do not touch the plug with wet hands.
• Hold the plug while unplugging the power cord from the wall outlet.
• Let the device cool down completely.

Warning of electrical voltage.

• Tasks that require opening the enclosure may only be carried out by an authorized specialist business.

Clean the device

Warning of electrical voltage.

• Never immerse the device in water!
• Clean the device with a soft, damp, and lint-free cloth. Make sure that no moisture enters the housing.
• Protect electrical components against moisture.
• Do not use aggressive cleaning agents such as cleaning sprays, solvents, alcoholic or abrasive cleaners to dampen the cloth. Wipe the housing dry after cleaning.

Storage

When the device is not in use, observe the following storage conditions:

• dry and protected against moisture and heat.
• in an upright position where it is protected from dust and direct sunlight.
• If necessary with a cover to protect it against dust ingress.
• Do not place additional devices or objects on top of the device to avoid damaging it.

Removal

• The crossed-out waste bin icon on waste electrical or electronic equipment indicates that this equipment may not be thrown in with household waste.
• You will find collection points for the free disposal of waste electrical and electronic equipment in your area. You can request the addresses of the municipality in your region.
• The separate collection of waste electrical and electronic equipment is collected here. The separation is intended to enable reuse, recycling, and other forms.
• The profits from the waste equipment contribute to the environment and human health.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>