BEGA 85 074 Bug Save light Building Element Head Instruction Manual

BEGA 85 074 Bug Save light Building Element Head Instruction Manual

Light building element

Instructions for use

Application

System light building element with shielded light for illuminating and designing squares, driveways and entrance areas.
Light exit 360°. The light is deflected by means of a conical reflector onto the surface to be illuminated.
A light building element tube is required for the installation of the light building element head, which must be ordered separately (see accessories).

Product description

Luminaire made of cast aluminium, aluminium and stainless steel
BEGA Unidure® coating technology
Clear synthetic cover with optical structure
Silicone gasket
Reflector surface made of pure aluminium
Connecting cable X05BQ-F 5 G 1 mm²
Cable length 3,1 m
BEGA Ultimate Driver ®LED power supply unit 220-240 V x 0/50-60 Hz DC 176-276 V
DALI controllable
Number of DALI addresses: 1
A basic isolation exists between power cable and control line
BEGA Thermal Control® Temporary thermal regulation to protect temperature- sensitive components without switching off the luminaire
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
Impact strength IK04
Protection against mechanical impacts < 0.5 joule
 – Conformity mark
Horizontal wind catching area: 0.032 m²
Weight: 4.0 kg
This product contains light sources of energy efficiency class(es) C, D
Dark Sky
The light of this luminaire is directed evenly and highly efficiently onto the surface to be illuminated. No light is emitted into the upper half-space of the luminaire.

Safety

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Installation

Thread the connection cable into the light building element tube. Align the light building element head and secure it in place.
Tighten the lateral hexagon socket screws (wrench size 4 mm).
Torque = 12 Nm.
Open the connection box.
Lead the luminaire wiring and mains supply cable through the cable entry into the connection box.
Make the electrical connection.
Observe the correct configuration of the connecting cable. Make the mains connection to the brown (L), blue (N) and green-yellow wires ( ****).
The control cables are connected via the two DALI-labelled wires white-red (wh-rd) and white-black (wh-bl). If these wires are not assigned, the luminaire will work with full light output.
Close the connection box.

Lamp

Module connected wattage| 20 W
Luminaire connected wattage| 22.5 W
Rated temperature| ta= 25 °C
Ambient temperature| ta max = 50 °C
85 024 K3
Module designation| 4x LED-1305/830
Colour temperature| 3000 K
Colour rendering index| CRI > 80
Module luminous flux| 3300 lm
Luminaire luminous flux| 2574 lm
Luminaire luminous efficiency| 114,4 lm / W
85 024 K4
Module designation| 4x LED-1305/840
Colour temperature| 4000 K
Colour rendering index| CRI > 80
Module luminous flux| 3480 lm
Luminaire luminous flux| 2714 lm
  Luminaire luminous efficiency| 120,6 lm / W

Cleaning · Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt and deposits. Do not use high pressure cleaners.

Please note:
Do not remove the desiccant bag from the luminaire housing.
It is needed to remove residual moisture.

Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective synthetic diffuser must be replaced.
Close the luminaire.

Accessories

The light building element head can be combined with the following light building element tubes:
Cylindrical aluminium poles, lacquered with access door and connection box 71 084
84 708  Pole with anch.section  H 3500 mm
84 709  Pole with baseplate  H 3500 mm
Cylindrical poles made of laminated wood in accordance with DIN EN 14080 and aluminium, with access door and connection box 71 084
84  710 Pole with anch.section  H 3500 mm
84 711  Pole with baseplate  H 3500 mm
70 899  Anchorage unit for light building element tube with base plate
For the accessories a separate instructions for use can be provided upon request.

Spares

BEGA Gantenbrink-Leuchten KG
Postfach 31 60
58689 Menden
info@bega.com
www.bega.com

Read More About This Manual & Download PDF:

References

• BEGA · Das gute Licht.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>