Z-LITE 735-5V-CH Vaughn 5 Light Chrome Bath Vanity Wall Light Instruction Manual
- June 1, 2024
- Z-Lite
Table of Contents
Z-LITE 735-5V-CH Vaughn 5 Light Chrome Bath Vanity Wall Light
FOR YOUR SAFETY WARNING
BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF; EITHER
THE FUSE IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF. GENERAL You don’t need
special tools to install this fixture. Be sure to follow the steps in the
order given. Under no circumstances should a fixture be hung on house
electrical wires, nor should a swag type fixture be installed on a ceiling
which contains a radiant type heating system. Read instructions carefully. If
you are unclear as to how to proceed, consult a qualified electrician.
NOTE : Proper wiring is essential for the safe operation of this fixture.
GENERAL
You don’t need special tools to install this fixture. Be sure to follow the
steps in the order given. Under no circumstances should a fixture be hung on
house electrical wires, nor should a swag type fixture be installed on a
ceiling, which contains a radiant type heating system. Read instructions
carefully. If you are unclear as to how to proceed, consult a qualified
electrician.
NOTE: Proper wiring is essential for the safe operation of this fixture.
FIXTURE ASSEMBLY
Carefully removed the fixture from the carton and check that all parts are included as shown in figure. Be careful not to misplace any of the screws or parts which are needed to install this fixture.
INSTALLATION
IMPORTANT : Do not attach fixture directly to outlet box.
STEP 1 : Secure the Mounting bar(F)with Mounting screw(G)to the Outlet
box(A). Attach the Back plate(J)against the Outlet box(A)
STEP 2 : Thread three Mounting screw(I) to the Mounting bar(F) with(J)
GROUNDING INSTRUCTIONS
STEP 1: Insert the green grounding screw into the hole with two raised dimples on the circular strap. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to ground wire from the outlet box (if not fixed on the outlet box) using a wire connector (not supplied). If ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES.
STEP 2: Take note of the color of the wire(s) on your fixture.
Identify which group your fixture wire(s) falls into and connect the wires
according to the directions below:
GROUP A: Connect to Black House Wire| GROUP B: Connect to Wh it e
House Wire
---|---
BLACK| WHITE
PARALLEL W I R E ( round & smooth)| PARALLEL W I R E ( square & ridged)
WHITE OR GREY WITH TRACER| WHITE OR GREY WITHOUT TRACER
BROWN GOLD OR BLACK WITHOUT TRACER| BROWN, GOLD OR BLACK WITH TRACER
*NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer wire is
square shaped or ridged and the less tracer wire is round in shape or smooth
(seen best when viewed from wire end.)
STEP 3 : Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. Do NOT twist wires together before using
wire connectors.
STEP 4: Fit a wire connector (not supplied) over the wires and screw the
connector clockwise until you feel a firmness.
STEP 5: Try gently to pull the connector off the wires. If you can pull
the connector off, carefully re-do steps 3 and 4, as above, and check again
for a firm connection.
STEP 6: Connect the fixture wire from group B to the white wire from the
outlet box in the same manner. Make sure no bare wires can be seen outside
wire connectors.
FINAL ASSEMBLY
STEP 1: After wires are connected, tuck them carefully inside outlet box.
Raise the back plate (J) then secure with the mounting screw (I).
STEP 2: Install bulb (Not include) (Please do not exceed the maximum
capacity recommended on the socket.)
STEP 3: Hang shade (K) over the sockets on back plate (J) secure with
three screws (L) on the cover.
CLEANING
To clean wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order replacement parts. All parts for this fixture can be ordered from place of purchase. Be sure to use exact wording from illustration when ordering parts.
Line art shown may not exactly match the fixture enclosed.
However, the installations do apply to this fixture.
ITEM NO: 735-1S 736-1S 735-2V 736-2V 735-3V 736-3V 735- 4V 736-4V 735-5V
736-5V
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>