Z-Lite 740P-5L 42 Inch Linear Light in Rubbed Brass Instruction Manual
- June 13, 2024
- Z-Lite
Table of Contents
Z-Lite 740P-5L 42 Inch Linear Light in Rubbed Brass
Product Information
This product is a fixture that is designed to be installed on a ceiling. It comes with a universal mounting plate, a mounting frame, a lamp cord, a coupling, a set screw, a figure 8 buckle, bridge wires, a junction box, wire connectors, a socket cup, abulb, and a glass shade.
Installation and Safety Instructions
-
Carefully remove the fixture from the carton and check that all parts are included.
-
Secure the universal mounting plate onto the outlet box using the provided box screw.
-
Grounding Instructions: – Insert the green grounding screw into the hole with two raised dimples on the circular strap. Wrap the ground wire from the fixture around the green grounding screw and connect it to the ground wire from the outlet box using a wire connector. -If the ground wire from the fixture is not supplied, wrap the ground wire from the outlet box around the green grounding screw and tighten it.
-
Fasten the mounting frame to the ceiling using long thick woodscrews.
-
Feed the lamp cord through the coupling and tighten the set screw to hold the fixture at the desired height.
-
Put the figure 8 buckle on the wire and snug it up to the fitting where the wire comes through the ceiling plate. Repeat for each pendant being attached to the canopy.
-
Add a section of bridge wire for every 4 lamp cords by attaching the wires from the lamp cords to one end of the bridge wire (white to white, black to black, ground to ground). 8. Group the remaining cords and lamp
wire together and attach them to the main power source from the junction box using wire connectors (white to white, black to black, ground to ground). -
Tuck excess wire inside of the junction box.
-
Raise the canopy to the mounting frame and fasten it in place with screws.
-
Install the bulb (not included) into the socket cup. 1
-
Install the glass shade into the socket cup by placing it inside and turning it.
Cleaning Instructions
To clean the fixture, wipe it with a soft cloth. Clean the glass shade with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool, or abrasive paper.
Ordering Parts
Keep this sheet for future reference and in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Make sure to use the exact wording from the illustration when ordering parts.
INSTALLATION AND SAFETY INSTRUCTIONS
FOR YOUR SAFETY
WARNING : BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF. GENERAL You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should a fixture be hung on house electrical wires, nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system. Read instructions carefully. If you are unclear as to how to proceed, consult a qualified electrician.
NOTE: Proper wiring is essential for the safe operation of this fixture.
GENERAL
You don’t need special tools to install this fixture. Be sure to follow the
steps in the order given. Under no circumstances should a fixture be hung on
house electrical wires, nor should a swag type fixture be installed on a
ceiling, which contains a radiant type heating system. Read instructions
carefully. If you are unclear as to how to proceed, consult a qualified
electrician.
NOTE: Proper wiring is essential for the safe operation of this fixture.
FIXTURE ASSEMBLY
Carefully removed the fixture from the carton and check that all parts are
included as shown in figure. Be careful not to misplace any of the screws or
parts, which are needed to install this fixture.
INSTALLATION
IMPORTANT: Do not attach fixture directly to outlet box. STEP1: Secure
universal mounting plate(L) on to outlet box with box screw(E).
Proceed to connect wires:
GROUNDING INSTRUCTIONS
STEP 1: Insert the green grounding screw into the hole with two raised dimples on the circular strap. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to ground wire from the outlet box (if not fixed on the outlet box) using a wire connector (not supplied). If ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it.
GROUP A: Connect to Black House Wire| GROUP B : Connect to W h i t e
House Wire
---|---
BLACK| WHITE
PARALLEL W I R E ( round & smooth)| PARALLEL W I R E ( square & ridged)
WHITE OR GREY WITH TRACER| WHITE OR G R E Y WITHUOT TRACER
BROWN GOLD OR
B L A C K WITHOUT TRACER
| BROWN, GOLD OR BLACK WITH TRACER
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES.
FINAL ASSEMBLY
Step 1 : Fasten the mounting frame (L) to ceiling. Be sure that the frame
is mounted securely to the building structure using long thick woodscrews (Not
included, #10 or greater recommended). Woodscrews should be long enough to be
in the wood structure at least 1.5” (not including frame, drywall/plaster, or
wall cladding). When needed refer to page 2 for extra fastening/safety cable
fastening instructions when applicable.
Step 2: Feed the lamp cord (C) through the coupling (H). Once fixture is
at the desired height, hold it in place by tightening the set screw (G). Put
the figure 8 buckle on the wire and snug it up to the fitting where the wire
comes through the ceiling plate. Repeat for each pendant being attached to the
canopy (I)
Step 3: Add a section of bridge wire for every 4 lamp cords (C). This is
done by taking a loose piece of wire 1’-2’ in length. Attach the wires from
the 4 lamp cords (C) to one end of the wire (white to white, black to black,
ground to ground).
Step 4: Group the remaining cords (C) and lamp wire together and attach
them to the main power source from the junction box with wire connectors. Once
again, white to white and black to black, ground to ground.
Step 5: Tuck excess wire inside of the junction box. Raise the canopy (I)
to the mounting frame (L). Be sure that no loose wires are being pinched.
Fasten the canopy (I) in place with screws (J)
Step 6: Install the bulb (D) (Not included) into the socket cup (B)
S t ep 7 : Install the glass shade (A) into the socket cup (B) by
placing it inside of the socket cup (B) and turning it.
CLEANING
To clean wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order replacement parts. All parts for this fixture can be ordered from place of purchase. Be sure to use exact wording from illustration when ordering parts.
Line art shown may not exactly match the fixture enclosed. However, the
installations do apply to this fixture.
ITEM NO: 740P-5L
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>