Z-Lite 1943P8-MB Glacier 8 Inch Pendant Light Instructions
- June 12, 2024
- Z-Lite
Table of Contents
Z-Lite 1943P8-MB Glacier 8-Inch Pendant Light
Product Information
This product is a lamp fixture that requires assembly and installation. It comes with a mounting plate, canopy, lamp holder, pipes, and necessary screws for installation. It is important to shut off the power at the fuse or circuit breaker before beginning installation. Before installation, consult local electrical codes for wiring and grounding requirements.
Product Usage Instructions
- Shut off the power at the circuit breaker box and remove the old fixture and all hardware from the outlet box.
- Unpack the new fixture carefully and lay out all the parts in a clear area, making sure not to lose any small parts necessary for installation.
- Thread the two mounting screws into the pre-drilled holes in the mounting plate spaced the same distance apart as the holes in the canopy. Attach the mounting plate to the outlet box with the two outlet box screws as shown. The side of the mounting plate marked GND must face out.
- The lamp body includes 8 pipes to be connected to various heights. Measure and determine the correct number of pipes required. Feed the wires from the lamp holder through pipes and canopy, and connect the pipe to the threaded nipple from the lamp holder. Thread the threaded nipple to the inside of each pipe, and connect all the pipes and canopy together until secure.
- Take this lamp body assembly to the ceiling outlet box and connect the electrical wires.
- Note: Make wire connections following proper electrical wiring procedures.
ASSEMBLY AND INSTALLATION INSTRUCTIONS
WARNING: SHUT POWER OFF AT THE FUSE OR CIRCUIT BREAKER!
Installation Steps:
- Shut off the power at the circuit breaker box. Remove the old fixture and all hardware from Outlet Box.
- Carefully unpack your new fixture and lay out all the parts in a clear area. Take care not to lose any small parts necessary for installation.
- Thread the two Mounting Screws into the pre-drilled holes in the Mounting Plate spaced the same distance apart as the holes in the Canopy. Attach the Mounting Plate to the Outlet Box with the two Outlet Box Screws as shown. The side of the Mounting Plate marked “GND” must face out.
- This lamp body includes 8pcs Pipes to be connected to various heights. Measure and determine the correct number of Pipes required. Feed the wires from Lamp Holder through the Pipes and Canopy, and connect the Pipe to the threaded nipple from Lamp Holder.
- Thread the threaded nipple to the inside of each Pipe, and connect all the Pipes and Canopy together until secure.
- Take this lamp body assembly to the ceiling Outlet Box, and connect the electrical wires.
- NOTE: make wires connections:
- Attach fixture ground wire to supply ground wire using a wire nut or attach them to the mounting plate with a green ground screw.
- Attach fixture white wire from the lamp body to supply white wire or ridge wire from a power source with a wire nut.
- Attach fixture black wire from the lamp body to supply black wire or smooth wire from the power source with a wire nut.
- Observing: positive wire with positive wire, negative wire with negative wire, ground wire with ground wire.
- Make sure all wire connectors are secured and do not easily pull off with a slight tug. After the wires are connected, tuck them carefully inside the Outlet Box. Raise the Canopy onto the Outlet Box, align screws on Mounting Plate with mounting holes in Canopy, and lock it securely with the Finials.
- Install the light bulb(Not included) in accordance with the fixture’s specifications.
- NOTE: DO NOT EXCEED THE MAXIMUM WATTAGE RATING!
- Raise the Glass Sheet to the Lamp Holder side and use Handle Screw to secure Glass Sheet as well as Plastic Shim onto Lamp Holder. Note: handle screws do not lock too tightly!!
- Your installation is now complete. Return power to the outlet box and test the lamp body
Note: handle screw do not lock too tightly
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>