Z-Lite 576M-2-BK-LED Edge Large LED Outdoor Wall Sconce Instruction Manual
- June 12, 2024
- Z-Lite
Table of Contents
Z-Lite 576M-2-BK-LED Edge Large LED Outdoor Wall Sconce
Product Information
The product models are 576S-2-XX-LED and 576M-2-XX-LED. The product includes the following components:
- Screw (2)
- Glass (3)
- LED Screw (4)
- LED (5)
- Quick Connector (6)
- Ground Green Screw
- Outlet Box Wire Connector
- Black Lantern Wire
- Ground Wire
- White Supply Wire
- Mounting Plate Screw (1)
Product Usage Instructions
Before starting the assembly, please read and save the entire user manual for future reference.
Tools & Materials Required
- Screwdriver
- Wire Cutters
- Adjustable Wrench
- Wiring Supplies
CAUTION: If you do not have electrical wiring experience, it is recommended to refer to a do-it-yourself wiring handbook or have your fixture installed by a qualified licensed electrician.
Prepare the Fixture
- Turn off the electricity before starting the assembly.
- Detach the mounting plate from the fixture.
- Mount the detached mounting plate to the outlet box on your wall.
CAUTION: LED fixtures can operate at high temperatures. Please use caution when touching during operation or after the operation.
FOR YOUR SAFETY WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF. GENERAL, You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should a fixture be hung on house electrical wires, nor should a swag-type fixture be installed on a ceiling that contains a radiant-type heating system. Read instructions carefully. If you are unclear as to how to proceed, consult a qualified electrician. NOTE: Proper wiring is essential for the safe operation of this fixture.
ASSEMBLY INSTRUCTIONS
576S-2-XX-LED & 576M-2-XX-LED
READ & SAVE INSTALLATION & OPERATION INSTRUCTIONS TOOLS & MATERIALS REQUIRED
- Screwdriver: Wire Cutters
- Adjustable: Wrench Wiring Supplies
CAUTION : Before assembly, refer to the ELECTRICAL CONNECTIONS section. If you do not have electrical wiring experience, refer to a do-it-yourself wiring handbook or have your fixture installed by a qualified licensed electrician.
GENERAL
- Be sure to read these instructions and review the diagrams thoroughly before beginning.
- Electrical connections must be by local codes, ordinances, or the National Electric Code. If you are unfamiliar with methods of installing electrical wiring, secure the services of a qualified licensed electrician.
- Before starting the installation, disconnect the power by turning off the circuit breaker or by removing the appropriate fuse at the fuse box. Turning the power off at the light switch is not sufficient to prevent electrical shock.
PREPARE THE FIXTURE
NOTE: First turn off the electricity Detach the mounting plate from the fixture and mount it to the outlet box on your wall.
ELECTRICAL CONNECTIONS 120V~, 60Hz
- Connect white wire(s) from the fixture to white neutral wire from the supply circuit. Connect black wire(s) to black hot wire from the supply circuit.
- Connect green wire to green or bare wire or grounding screw on the mounting bracket. In all cases grounding conductor to earth must be used. Use UL/CSA Listed wire connects suitable for the size, type, and number of conductors.
- No loose strands or loose wires should be present. Secure wire connectors with UL/CSA Listed electrical tape.
- Spread electrical splices so black wires are on one side of the outlet box and white wires on the other.
- Attach the fixture to the fixture to the mounting plate with side screws. Be careful not to pinch any of the wires between the fixture and the mounting plate or outlet box.
- Once the fixture is mounted on the wall, caulk the space between the wall and the upper area of the back plate to prevent water from seeping into the outlet box. Leave the bottom area un-caulked for drainage of any water which might leak into the enclosure.
- Installation is complete. Turn on the power at the circuit breaker or fuse box. Turn the light switch on to activate the fixture.
- LED replacement: First make sure the power is turned off. Remove the fixture from the wall by removing the screws(1), remove the screws(2) on the glass(3), then remove the lid screws(4) in the LED(5) and pull out the LED, finally replace the LED module by a quick connector(6), secure the screws.
CAUTION : LED fixtures can operate at high temperatures please use caution when touching during operation or after operation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>