Z-Lite 340-2V-MB Heirloom Gold Two Light Vanity Fixture Instructions
- June 8, 2024
- Z-Lite
Table of Contents
Z-Lite 340-2V-MB Heirloom Gold Two Light Vanity Fixture
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF. GENERAL You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should a fixture be hung on house electrical wires, nor should a swag-type fixture be installed on a ceiling that contains a radiant-type heating system. Read instructions carefully. If you are unclear as to how to proceed, consult a qualified electrician.
NOTE: Proper wiring is essential for the safe operation of this fixture.
GENERAL
You don’t need special tools to install this fixture. Be sure to follow the
steps in the order given. Under no circumstances should a fixture be hung on
house electrical wires, nor should a swag type fixture be installed on a
ceiling, which contains a radiant type heating system. Read instructions
carefully. If you are unclear as to how to proceed, consult a qualified
electrician.
NOTE: Proper wiring is essential for the safe operation of this fixture.
FIXTURE ASSEMBLY
Carefully removed the fixture from the carton and check that all parts are included as shown in figure. Be careful not to misplace any of the screws or parts, which are needed to install this fixture.
INSTALLATION
IMPORTANT: Do not attach fixture directly to outlet box.
- STEP1: Secure universal mounting plate(G) onto outlet box with box screw(H).
Proceed to connect wires:
GROUNDING INSTRUCTIONS STEP 1: Insert the green grounding screw into the hole with two raised dimples on the circular strap. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to ground wire from the outlet box (if not fixed on the outlet box) using a wire connector (not supplied). If ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it.GROUP A: Connect to Black
House Wire
| GROUP B : Connect to W h i t e
House Wire
---|---
BLACK| WHITE
*PARALLEL W I R E ( round &
smooth)
| *PARALLEL W I R E ( square &
ridged)
WHITE OR GREY WITH TRACER| WHITE OR G R E Y
W I T H O U T TRACER
BROWN G O L D OR
B L A C K WITHOUT TRACER
| BROWN, GOLD OR BLACK WITH TRACER
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES.
- STEP 2: Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into and connect the wires according to the directions below:
*NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer wire is square shaped or ridged and the less tracer wire is round in shape or smooth (seen best when viewed from wire end.) - STEP 3: Take your fixture wire(s) from group A and place evenly against the black wire from the outlet box. Do NOT twist wires together before using wire connectors.
- STEP 4: Fit a wire connector (not supplied) over the wires and screw the connector clockwise until you feel a firmness.
- STEP 5: Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do steps 3 and 4, as above, and check again for a firm connection
- STEP 6: Connect the fixture wire from group B to the white wire from the outlet box in the same manner
FINAL ASSEMBLY
- STEP1: After wires are connected, tuck them carefully inside outlet box.
- STEP2: Securing the back plate (E) to the mounting plate (G) with screws (F).
- STEP3: Secure the Glass shade (C) on the socket (D)with Ring(B).
- STEP4: Install the bulb (A) (NOT INCLUDED) on the socket (D)
CLEANING
To clean wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. All parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when ordering parts.
Line art shown may not exactly match the fixture enclosed. However, the
installations do apply to this fixture. ITEM NO: 340-2V / 3V / 4V / 5V
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>