Z-Lite 337MP-MB Burren 1 Light 9 inch Matte Black Mini Pendant Ceiling Light Instruction Manual
- June 8, 2024
- Z-Lite
Table of Contents
Z-Lite 337MP-MB Burren 1 Light 9-inch Matte Black Mini Pendant Ceiling
Light
FOR YOUR SAFETY
- WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF.
GENERAL
You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should a fixture be hung on house electrical wires, nor should a swag-type fixture be installed on a ceiling, which contains a radiant-type heating system. Read instructions carefully. If you are unclear as to how to proceed, consult a qualified electrician NOTE: Proper wiring is essential for the safe operation of this fixture.
FIXTURE ASSEMBLY
Carefully remove the fixture from the carton and check that all parts are included as shown in the figure. Be careful not to misplace any of the screws or parts, which are needed to install this fixture.
- STEP 1: Thread rod (K) into coupling (L). Carefully pass the wires through each rod during assembly. Repeat step 1 with rods (G), (H), (I), and (J) until the desired hanging height is reached.
- STEP 2: Thread the rod (G) onto coupling (F).
INSTALLATION
IMPORTANT: Do not attach the fixture directly to the outlet box.
- STEP 1: Thread the mounting screws (C) into the match holes in the mounting bar (B).
- STEP 2: Secure mounting bar (B) to the outlet box with outlet box screws (A).
GROUNDING INSTRUCTIONS
-
STEP 1: Insert the green grounding screw into the hole with two raised dimples on the mounting bar. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to the ground wire from the outlet box (if not fixed on the outlet box) using a wire connector (not supplied). If the ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES. -
STEP 2: Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into and connect the wires according to the directions below:
NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer wire is square shaped or ridged and the less tracer wire is round in shape or smooth (seen best when viewed from the wire end.) -
STEP 3: Take your fixture wire(s) from group A and place it evenly against the black wire from the outlet box. Do NOT twist wires together before using wire connectors
-
STEP 4: Fit a wire connector over the wires and screw the connector clockwise until you feel firmness.
-
STEP 5: Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do steps 3 and 4 as above, and check again for a firm connection.
-
STEP 6: Connect the fixture wire from group B to the white wire from the outlet box in the same manner. Make sure no bare wires can be seen outside wire connectors.
FINAL ASSEMBLY
- STEP 1: After the wires are connected, tuck them carefully inside the outlet box. Raise canopy (D) allowing the mounting screw (C) to protrude through the hole in the canopy (D), and secure with ball nut (E).
- STEP 2: Place the glass (Q) over the socket (O), then secure it with the retaining ring (P).
- STEP 3: Secure the decorative arm (R) to the cup (M) and metal ring (T) with the screw (N, S).
- STEP 4: Install lamp (Not supplied). (Please do not exceed the maximum capacity recommended on the socket.)
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. All parts for this fixture can be ordered from the place of
purchase. Be sure to use exact wording from illustrations when ordering parts.
ITEM NO: 337MP 337P12
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>