Z-Lite 2307-1S-MB Wall Light Instruction Manual

Z-Lite 2307-1S-MB Wall Light

Specifications

• Fixture type: Ceiling fixture
• Installation: Requires standard electrical wiring
• Materials: Metal, plastic
• Maximum bulb capacity: Refer to socket rating

Installation and Safety Instructions

For Your Safety: Before starting theare working on is shut off. This can be done by removing the fuse or shutting off the circuit breaker.
General Instructions: No special tools are required for installation. Follow the steps in the given order. Do not hang the fixture on house electrical wires or install a swag type fixture on a ceiling with a radiant heating system. If unsure, consult a qualified electrician.
Fixture Assembly: Carefully unpack the fixture and ensure all parts are included. Keep track of screws and parts needed for installation.

Grounding Instructions

1. Step 1: Insert the green grounding screw into the designated hole on the crossbar. Connect the ground wire from the fixture to the green grounding screw and then to the outlet box’s ground wire using a wire connector if necessary.
2. Step 2: Connect fixture wires based on color= groups (A and B) to the corresponding house wires (Black and White) following the provided guidelines.

Final Assembly

1. Step 1: Once wires are connected, carefully tuck them inside the outlet box. Secure the backplate to the crossbar and tighten with the cap finial.
2. Step 2: Install the lamp ensuring not to exceed the maximum recommended capacity for the socket.

FAQ

Q: Can I install this fixture on my own?
A: While no special tools are required, proper wiring is crucial for safe operation. If unsure, it’s recommended to consult a qualified electrician.
Q: What should I do if I can pull the wire connector off?
A: If you can pull off the wire connector, carefully redo the connection steps ensuring a firm connection is established before proceeding further.

INSTALLATION AND SAFETY INSTRUCTIONS

FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF.

GENERAL
You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should a fixture be hung on house electrical wires, nor should a swag type fixture be installed on a ceiling, which contains a radiant type heating system. Read instructions carefully. If you are unclear as to how to proceed, consult a qualified electrician.
NOTE: Proper wiring is essential for the safe operation of this fixture.

FIXTURE ASSEMBLY
Carefully removed the fixture from the carton and check that all parts are included as shown in figure. Be careful not to misplace any of the screws or parts, which are needed to install this fixture.

INSTALLATION

IMPORTANT: Do not attach fixture directly to the outlet box.

1. STEP 1: Secure crossbar (A) to outlet box with outlet box screws (C).

GROUNDING INSTRUCTIONS

• STEP 1: Insert the green grounding screw into the hole with two raised dimples on the crossbar. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to the ground wire from the outlet box (if not fixed on the outlet box) using a wire connector (not supplied). If the ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw (B) and tighten it.
  NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES.

• STEP 2: Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into and connect the wires according to the directions below:

*NOTE: When parallel wire (SPT -I & SPT -2) is used, the tracer wire is square-shaped or ridged and the less tracer wire is round in shape or smooth (Seen best when viewed from wire end.)

• STEP 3: Take your fixture wire(s) from group A and place evenly against the black wire from the outlet box. Do NOT twist wires together before using wire connectors.
• STEP 4: Fit a wire connector (not supplied) over the wires and screw the connector clockwise until you feel a firmness.
• STEP 5: Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do steps 3 and 4, as above, and check again for a firm connection.
• STEP 6: Connect the fixture wire from group B to the white wire from the outlet box in the same manner. Make sure no bare wires can be seen outside wire connectors.

FINAL ASSEMBLY

1. STEP 1: After the wires are connected, tuck them carefully inside the outlet box. Raise the backplate (H) to the crossbar (A) and tighten with the cap finial (G) to the nipple of the crossbar(A) through the hole of the backplate(H).
2. STEP 2: Install lamp. (Please do not exceed the maximum capacity recommended on the socket.) bulb not included.

CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool, or abrasive paper.

ORDERING PARTS

Keep this sheet for future reference, and in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustrations when ordering parts.

Line art shown may not exactly match the fixture enclosed. However, the installations do apply to this fixture.
ITEM NO. 2307-1S-MB,2307-1S-RB,2307-1S-BN,2307-1S-MGLD

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>