WPS2040M Cooper Lighting Recalls Solar Battery Powered Instruction Manual

WPS2040M Cooper Lighting Recalls Solar Battery Powered

Product Information

Specifications

• Model: WPS2040M
• Packaging Contents:
  • A. Light fixture Luminaire Luminaria
  • B. Solar panel with 3ft. cord
  • C. (2) Mounting brackets
  • D. Mounting base (2)
  • E. Mounting stand
  • F. Mounting pin
  • G. Mounting pin cap
  • H. Frictional gasket
  • I. Mounting plate
  • J. (8) Mounting screws
  • K. (4) Drywall anchors
  • L. 6ft.USB Cable

Product Usage Instructions

Installation

Solar Panel

1. Assemble the solar panel mounting bracket:
   • Identify the frictional gasket and place it on the mounting stand.
   • Place the mounting base on a hard flat surface.
   • Insert the mounting stand into the mounting base until a click is felt and heard.
   • Align the arrow on the mounting stand with the arrow on the mounting plate, then insert the mounting pin through both to lock them together.
   • Push the mounting pin cap into the open end of the mounting pin.
2. Choose a location to mount the solar panel, ensuring it faces south and is clear of obstructions.
3. Mount the assembled bracket onto a solid surface using four mounting screws.
4. Slide the solar panel onto the mounting plate until an audible click is felt and heard.

Lighting System

1. Check that the included solar panel extension cord will reach the solar panel input.
2. Mount your lighting system using one of three methods: Direct Mount, D-Ring, or Bracket Mount.
3. Direct Mount: Attach the lighting system directly to a wall or ceiling using the provided mounting screws.
4. D-Ring: Hang or suspend the lighting system by one or both of the D-Rings securely fastened to the mounting surface.

Frequently Asked Questions (FAQ)

• Q: How should I clean the solar panel?
  A: Periodically clean the solar panel with a soft wet cloth to remove any dirt or debris that may obstruct sunlight exposure.

• Q: What should I do if the lighting system does not turn on?
  A: Check the connections and ensure that the solar panel is receiving an adequate amount of sunlight. If issues persist, contact customer support for further assistance.

PACKAGING CONTENTS

ITEMS REQUIRED
(Purchase separately)

• Phillips screwdriver
• 3/16” drill bit (for anchors)
• Hammer (for anchors)

PRODUCT OVERVIEW

This lighting system is designed for off-grid operation, utilizing an integrated rechargeable lithium battery pack and dimmer control for longer periods of use between charging. The battery pack can be charged either with the included solar panel, which converts sunlight into energy, or with an external USB power supply (purchased separately). This system features an integrated 360° motion sensor that turns the light on automatically when motion is detected at night or in the dark, and can also be used without the motion sensor, allowing the light to remain on regardless of motion events or ambient light levels.

WARNINGS AND CAUTIONS

INSTRUCTIONS PERTAINING TO A RISK OF FIRE OR INJURY TO PERSONS.

• To reduce the risk of fire or injury to persons, read and follow these instructions:
• DO NOT disassemble the lighting system, housing or components
• DO NOT dispose of this product in fire. Batteries inside this product may explode or leak.
• DO NOT puncture, tamper with, or attempt to modify the battery pack.
• DO NOT install or use this system near sources of excessive heat
• Lithium-ion batteries must be disposed of by local waste ordinances and regulations.
• DO NOT operate a luminaire with a missing or damaged lens.
• DO NOT cut, tamper with, or attempt to modify the solar panel wire or USB cable.
• For indoor or outdoor use.

SAVE THESE INSTRUCTIONS.

FOR BEST RESULTS

• Allow fixture to receive three full days of sunlight before use.
• Locate solar panel in an area that will receive the Mximum amount of sunlight during the daylight hours. The solar panel mustreceive at least 3-4 hours of direct sunlight daily.
• Once charged, test the system before permanently installing.
• Position the motion sensor so motion moves across the detection zone (Fig. 1).
• Keep solar panel clear of any objects that will block the sunlight. It will be necessary to periodically clean the solar panel with soft wet cloth.

INSTALLATION

Solar Panel

1. Assemble the solar panel mounting bracket (Fig 2):
   • Identify the frictional gasket(H) and place on the mounting stand(E)
   • Place the mounting base(D) on a hard flat surface. Insert mounting stand(E) into the mounting base(D) until a click is felt and heard.
   • Align the arrow on the mounting stand(E) with the arrow on the mounting plate(I), inserting the mounting pin(F) through both to lock them together (Fig 3).
   • Push the mounting pin cap(G) into the open end of the mounting pin(F). The inside edge of the pin cap(G) should be flush with the mounting plate(I).
2. Choose a location to mount the solar panel(B), ensuring the solar panel extension cord(M) will reach the lighting system. For best results the solar panel should face south, and be clear of any obstructions that may impede exposure to sunlight. The bracket provides nearly 360° of rotation, and 120° of tilt.
3. Mount the assembled bracket onto a solid surface, using four of the mounting screws(J) (Fig 4).
4. Slide the solar panel(B) onto the solar panel mounting plate(I) until an audible click is felt and heard (Fig. 5). Make any final adjustments to the panel to optimize exposure to sunlight.

Lighting System

1. Before installing, check to ensure the included solar panel extension cord(M) will reach the solar panel input on the endcap (Fig. 6 ).
2. Mount your lighting system choosing one of three methods: Direct Mount, D-Ring, or Bracket Mount.

Direct Mount:
Using the 4 of the mounting screws provided(J), attach the lighting system directly to a wall or ceiling using the attachment points located in the corners (Fig. 7). If anchors(K) are required, i.e. for drywall installation, use a 3/16” drill bit to create pilot holes and set the anchors in place with a hammer.

D-Ring:
Your lighting system can be hung or suspended by one or both of the D-Rings. Simply rotate one or both rings out from the housing, ensure the support method used is securely fastened to the mounting surface, and place the system into position (Fig. 8). create pilot holes and set the anchors in place with a hammer.

Bracket Mount:
Attach the two included brackets (C) to a wall or ceiling using the fasteners provided. Ensure the brackets are parallel and aligned with each other, positioned no more than 9″ apart (Fig. 9). Locate the grooves on the long sides of the fixture, rotating and snapping the fixture into the brackets. Remove by pressing down on the tabs on the brackets.

Outdoor Installation:
This system is designed to withstand rain and can be installed and used outdoors, however, the following guidelines must be adhered to:

• Only the solar panel port can be used when the system is exposed to moisture. The USB ports are not designed for use in wet conditions.
• All ports not in use must have the port covers securely in place at all times to prevent water intrusion.
• The ports (in a vertical orientation) or control side (in a horizontal orientation) of the system should always be oriented downward to protect against water intrusion.
• The system is designed to operate between 0° and 104°F. To protect the Li-ion battery pack, the internal charging circuitry will not allow the battery to charge below 32°F.

FUNCTIONS

Your fixture has three operating modes which can by selected by pressing the power button repeatedly: ON, AUTO and OFF. As you cycle through these modes the mode text will briefly illuminate to confirm the mode selected.

• ON mode: this mode keeps the light on indefinitely, bypassing inputs from the motion sensor or photo sensor. Note that in ON mode the system will not shut down until you change modes or the battery is depleted.
• AUTO mode: this mode utilizes the integrated motion sensor and photo sensor, turning the light on, at night or in the dark, only when motion is detected. The light will deactivate once no motion has been detected for 3 minutes. The onboard motion sensor has a detection range of 15’ with a detection zone of 360°.
• OFF mode: from AUTO mode, press the power button once more to shut the light off. The charging and discharging functions will continue to operate in OFF mode.
• Dimming: the system is equipped with an integrated dimmer that can be used in ON or AUTO mode. Turn the knob to the left to dim the light output and extend battery run time. Turn the knob to the right to increase output, which will shorten battery run time. See Table 1 below for fixture run time estimates.
• USB Output: the USB output produces 5V 2.1A, and is useful for charging and/or operating most smart devices and accessories requiring a USB input. Note that the integrated power supply is a 8800mAh Li-ion battery pack, and any charging from the power supply will reduce the run time of the light fixture on a single charge.

TABLE 1
Approximate Run Times and Initial Lumens Based On Dimming Level:
All figures assume the battery pack is fully charged

CHARGING

This system is capable of being charged with the included solar panel, or via micro USB. See Table 2 below for approximate charge times based on power source and input power.

• USB Charging:
  To charge the fixture using a mini USB charging cord (L), connect the mini USB side of the cord to the mini USB input on the fixture (Fig. 10). DO NOT use any USB power source exceeding 5V 2.1A power supply. Once an input charge is detected, the battery indicator will flash, indicating the battery level. Once the battery is fully charged, the indicator will remain a solid green.

• Solar Panel Charging:
  Connect the solar panel cord directly into the solar panel input port on the fixture (Fig 10); use of the 17’ extension cord (M) is optional. Please note that the battery indicatory lights do not come on when charging with the solar panel in order to conserve power and accelerate charge time.

TABLE 2.
Typical Charge Times:

TROUBLESHOOTING

Light does not come on when in ON mode| •  Press the power button to cycle through the operating modes, verifying the level of charge using the battery level indicator.

•  Ensure the battery is fully charged, using the USB input if possible.

•  When using the solar panel, allow at least three (3) full sunny days for the first charge or any time the battery pack becomes completely depleted.

---|---
Light does not come on when in AUTO mode| • The AUTO mode utilizes the integrated photo control and will not allow the light to come on when ambient light levels are too high. Ensure ambient light levels are low enough to activate the light. Test by completely covering the motion sensor with your hand or other opaque object.

•  Press the power button to cycle through the operating modes, verifying the level of charge using the battery level indicator.

•  Ensure the battery is fully charged, using the USB input if possible.

• When using the solar panel, allow at least three (3) full sunny days for the first charge or any time the battery pack becomes depleted.

Motion Sensor is malfunctioning| 1. The motion sensor produces a detection zone extending 60° from center, or 120° total angle. Ensure the motion triggering event falls within the detection zone.

2. The motion sensor utilizes PIR (passive infrared) technology, which detects movement and changes in relative heat. Extreme ambient temperatures may reduce or inhibit motion detection.

3. Relocate the fixture away from trees, moving cars, standing

water or other objects that may potentially cause interference.

USB output is not working| •  Verify battery level is full using battery level indicator lights by cycling the power button to the ON mode.

•  Verify the USB auxiliary device is compatible with 5V 2.1A input.

•  Ensure all connections on USB ports are secure

Battery Indicator Lights do not come on| •  Cycle power button to ON mode.

•  Battery indicator lights work when in ON mode and may not be on during AUTO mode when light is off.

•  If the main light is off and you are not charging or discharging using either USB port than the battery indicator light will not be on. This is intentional to conserve battery life.

•  Battery indicator lights do not come on during solar panel charging and the main light is off. This is intentional to conserve battery life.

1-YEAR LIMITED WARRANTY

THE FOLLOWING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
Cooper Lighting Solutions (“CLS”) warrants to customers that, for a period of one year from the date of purchase, CLS products will be free from defects in materials and workmanship. The obligation of CLS under this warranty is expressly limited to the provision of replacement products. This warranty is extended only to the original purchaser of the product. A purchaser’s receipt or other proof of date of original purchase acceptable to CLS. This is required before warranty performance shall be rendered. This warranty does not apply to CLS products that have been altered or repaired that have been subjected to neglect, abuse, misuse or accident (including shipping damages). This warranty does not apply to products not manufactured by CLS that have been supplied, installed, and/or used in conjunction with CLS products. Damage to the product caused by replacement bulbs or corrosion or discolouration of brass components are not covered by this warranty.

LIMITATION OF LIABILITY:
IN NO EVENT SHALL CLS BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (REGARDLESS OF THE FORM OF ACTION, WHETHER IN CONTRACT, STRICT LIABILITY, OR IN TORT INCLUDING NEGLIGENCE), NOR FOR LOST PROFITS; NOR SHALL THE LIABILITY OF CLS FOR ANY CLAIMS OR DAMAGE ARISING OUT OF OR CONNECTED WITH THESE TERMS OR THE MANUFACTURE, SALE, DELIVERY, USE, MAINTENANCE, REPAIR OR MODI-FICATION OF CLS PRODUCTS, OR SUPPLY OF ANY REPLACEMENT PARTS THEREFORE, EXCEED THE PURCHASE PRICE OF CLS PRODUCTS GIVING RISE TO A CLAIM. NO LABOR CHARGES WILL BE ACCEPTED TO REMOVE OR INSTALL FIXTURES.

To obtain warranty service, please contact CLS, at 1-800-334-6871, press option 2 for Customer Service, or via e-mail at ConsumerProducts@cooperlighting.com and include the following information:

• Name, address and telephone number
• Date and place of purchase
• Catalog and quantity purchase
• Detailed description of problem

All returned products must be accompanied by a Return Goods Authorization Number issued by the Company and must be returned freight prepaid. Any product received without a Return Goods Authorization Number from the Company will be refused. CLS is not responsible for merchandise damaged in transit. Repaired or replaced products shall be subject to the terms of this warranty and are inspected when packed. Evident or concealed damage that is made in transit should be reported at once to the carrier making the delivery and a claim filed with them.

Reproductions of this document without prior written approval of CLS are strictly prohibited. For assistance, call 1-800-334-6871 or e-mail us at ConsumerProducts@cooperlighting.com Printed in China

1121 Highway 74 South, Peachtree City, GA 30269
P:770-486-4800
www.cooperlighting.com
© 2020 Cooper Lighting Solutions.

Questions?
1-800-334-6871
ConsumerProducts@cooperlighting.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>