ENDLESS SUMMER GAD17107ES “The Marc” Outdoor Rectangular Steel Frame LP

Gas Fire Pit

WARNING
FOR OUTDOOR USE ONLY.

•  Installation and service must be performed by a qualified installer, service agency or gas supplier.

WARNING
FOR YOUR SAFETY:

•  If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life.
•  WHAT TO DO IF YOU SMELL GAS:
• Do NOT try lighting any appliance.
• Do NOT touch any electrical switch; do NOT use any phone in your building.
•  Immediately call your gas supplier from a neighbor’s phone.
•  Follow the gas supplier’s instructions.
•  If you cannot reach your gas supplier, call the fire department.
•  Do Not Use For Cooking.

WARNING
FOR YOUR SAFETY:

•  INSTALLER: Leave this manual with the appliance.
•  CONSUMER: Retain this manual for future reference.

WARNING
FOR YOUR SAFETY:

• Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage.
• Read the installation, operation and maintenance instructions thoroughly before installing or servicing this equipment.

DANGER
FIRE OR EXPLOSION HAZARD
If you smell gas:

•  Shut off gas to appliance.
• Extinguish any open flame.
•  If odor continues, leave the area immediately.
• After leaving the area, call your gas supplier or fire department.

Failure to follow these instructions could result in fire or explosion, which could cause property damage, personal injury, or death.

WARNING
FOR YOUR SAFETY:

1. Do not store or use gasoline, or other flammable vapors and liquids, in the vicinity of this or any other appliance.
2. An LP-cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.

DANGER
Do NOT leave this appliance unattended while it is in operation.

DANGER
CARBON MONOXIDE HAZARD

• This appliance can produce carbon monoxide which has no odor.
•  Using it in an enclosed space can kill you.
•  Never use this appliance in an enclosed space such as a camper, tent, car or home.

The use and installation of this product must conform to local codes. In absence of local codes, use the latest edition of the National Fuel Gas Code, ANSI Z223.1/NFPA 54, or International Fuel Gas Code. This appliance, when installed, must be electrically grounded in accordance with local codes, or in the absence of local codes with the National Electrical Code, ANSI/NFPA 70, if applicable. For installation in Canada – these instructions, while generally acceptable, do not necessarily comply with the Canadian installation codes, particularly with piping above and below ground. In Canada the installation of this appliance must comply with local codes and/or standard CAN/CGA B149.1 (installation code for propane burning appliances and equipment).
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
If you are assembling this unit for someone else, give this manual to them to read and save for future reference.
WARNING: This product can expose you to chemicals, including carbon monoxide, soot, Diisononyl Phthalate (DINP), lead and lead components which are known to the State of California to cause cancer, birth defects, and other reproductive harm. Wash your hands after handling this product. For more information go to www.P65Warnings.ca.gov.
Patents Pending
Manufactured in China for: Mr. Bar-B-Q Products LLC
10 Hub Dr., Ste 101, Melville, NY 11747 • 1.888.398.8643 • MrBarBQProducts.com
© Mr. Bar-B-Q Products LLC
Endless Summer® is a Registered Trademark of Mr. Bar-B-Q Products LLC

Important Safeguards

DANGER
FLAMMABLE GAS UNDER PRESSURE. LEAKING LP-GAS MAY CAUSE A FIRE OR EXPLOSION IF IGNITED CAUSING SERIOUS BODILY INJURY OR DEATH. CONTACT LP GAS SUPPLIER FOR REPAIRS, OR DISPOSAL OF THIS CYLINDER OR UNUSED LP-GAS.

WARNING
FOR OUTDOOR USE ONLY. DO NOT USE OR STORE CYLINDER IN A BUILDING, GARAGE OR ENCLOSED AREA.

WARNING:

•  Know the odor of LP-gas. If you hear, see or smell leaking LP-gas, immediately get everyone away from the cylinder and call the Fire Department. Do not attempt repairs.

•  Caution your LP-gas supplier to:
  Be certain cylinder is purged of trapped air prior to first filling.
  Be certain not to over fill the cylinder.
  Be certain cylinder requalification date is checked.

• LP-gas is heavier than air and may settle in low places while dissipating.

• Contact with the liquid contents of cylinder will cause freeze burns to the skin.

•  Do not allow children to tamper or play with cylinder.

•  When not connected for use, keep cylinder valve turned off. Self contained appliances shall be limited to a cylinder of 30 lb capacity or less.

•  Do not use, store or transport cylinder where it would be exposed to high temperatures. Relief valve may open allowing a large amount of flammable gas to escape.

• When transporting, keep cylinder secured in an upright position with cylinder valve turned off.

WHEN CONNECTING FOR USE:

• Use only in compliance with applicable codes.
• Read and follow manufacturer’s instructions.
•  Consult manufacturer’s instructions concerning the cylinder connection provided with your appliance.
•  Be sure regulator vent is not pointing up.
•  Turn off all valves on the appliance.
• Do not check for gas leaks with a match or open flame. Apply soapy water at areas marked “X”. Open cylinder valve. If bubble appears, close valve and have LP-gas service person make needed repairs. Also, check appliance valves and connections to make sure they do not leak before lighting appliance.
• Light appliance(s) following manufacturer’s instructions.
• When appliance is not in use, keep the cylinder valve closed.

DO NOT REMOVE, DEFACE, OR OBLITERATE THIS LABEL

• EXCEPT AS AUTHORIZED BY ANSI/NFPA 58.

DANGER: Do not store a spare LP cylinder under or near a barbecue grill, or other heat sources. NEVER fill an LP cylinder beyond 80% full: a fire causing death or serious injury may occur.

•  Failure to follow the dangers, warnings and cautions in this manual may result in serious bodily injury or death, or in a fire or an explosion causing damage to property.

WARNINGS

•  Do NOT use this outdoor fire pit without reading the entire owner’s manual.

•  This appliance is for outdoor use only, and should NOT be used in a building, garage or any other enclosed area.

•  Do NOT operate, light or use this appliance within ten feet (3.05 m) of walls, structures or buildings.

•  For residential use only. This outdoor fire pit is NOT for commercial use.

• Do NOT use this outdoor fire pit for indoor heating. TOXIC carbon monoxide fumes can accumulate and cause asphyxiation.

•  This outdoor fire pit is safety certified for use in the United States and/or Canada only. Do NOT modify for use in any other location. Modification will result in a safety hazard and will void your warranty.

• Apartment dwellers: Check with management to learn the requirements and fire codes for using a liquid propane (LP) gas outdoor fire pit in your apartment complex. If allowed, use outside on the ground floor with a ten foot (3.05 m) clearance from any structure. Do NOT use on or under balconies.

•  This outdoor fire pit, from the factory, is for use with LP gas only. The conversion to or attempted use of natural gas in this outdoor fire pit is dangerous, may cause bodily harm and will void your warranty.

•  LP gas characteristics:

• LP gas is flammable and hazardous if handled improperly. Become aware of the characteristics before using any LP gas product.

•  LP gas is explosive under pressure, heavier than air, and settles/pools in low areas.

•  LP gas in its natural state has no odor. For your safety, an odorant is added that smells like rotten cabbage.

• Contact with LP gas can cause freeze burns to skin.

•  LP gas tank needed to operate. Only tanks marked “propane” may be used.

•  The LP gas cylinder must be constructed and marked in accordance with the U.S. Department of Transportation (D.O.T.) Specifications for LP-Gas Cylinders, or the Standard for Cylinders, Spheres and Tubes for the Transportation of Dangerous Goods and Commission, CAN/CSA-B339 as applicable.

•  LP gas tank must be arranged for vapor withdrawal.

• The LP gas tank must have a listed overfilling prevention device (OPD) and a QCCI or Type I (CGA810) LP gas tank connection.

• The LP gas tank must have a tank collar to protect the tank valve.

•  Never use an LP gas tank with a damaged body, valve, collar or footing.

• Dented or rusted LP gas tanks may be hazardous and should be checked by your LP gas supplier prior to use.

•  The LP gas tank should not be dropped or handled roughly.

• Tanks must be stored outdoors, out of the reach of children and must not be stored in a building, garage or any other enclosed area. Your LP gas tank must never be stored where temperatures can reach over 125°F.

• Do NOT insert any tool or foreign object into the valve outlet or safety relief valve. You may damage the valve and cause a leak. Leaking propane may result in explosion, fire, severe personal injury or death.

• Never keep an LP gas tank in a hot car or trunk. Heat will cause the gas pressure to increase, which may open the relief valve and allow gas to escape.

•  Place dust cap on cylinder valve outlet whenever the cylinder is not in use. Only install the type of dust cap on the cylinder valve outlet that is provided with the cylinder valve. Other types of caps or plugs may result in leakage of propane.

• Do NOT store a spare LP gas tank under or near this appliance.

•  Never fill the cylinder beyond 80 percent full.

• A fire causing serious injury or damage to property may occur if the above is not followed exactly.

•  Your outdoor fire pit has been checked at all factory connections for leaks. Recheck all connections as described in the “Operating Instructions” section, as shipping can loosen connections.

•  Check for leaks even if your unit was assembled for you by someone else.

•  Do NOT operate if a gas leak is present. Gas leaks may cause a fire or explosion.

•  You must follow all instructions in the “Checking for Leaks” section before operating. To prevent a fire or explosion when testing for a leak:

•  Always perform a leak test before lighting this outdoor fire pit and each time the tank is connected for use.

• No smoking. Do NOT use or permit sources of ignition in the area while conducting a leak test.

• Conduct the leak test outdoors in a well-ventilated area.

• Do NOT use matches, lighters or a flame to check for leaks.

• The use of alcohol, prescription or non-prescription drugs may impair the consumer’s ability to properly assemble or safely operate the appliance.

• Strong odors, colds, sinus congestion, etc. may prevent the detection of propane. Use caution and common sense when testing for leaks.

• Do NOT use this outdoor fire pit until any and all leaks are corrected. If you are unable to stop a leak, disconnect the LP gas supply. Call a gas appliance serviceman or your local LP gas supplier.

•  Do NOT store or use gasoline or other flammable liquids or vapors within 25 feet (7.62 m) of this appliance.

•  Do NOT use in an explosive atmosphere. Keep outdoor fire pit area clear and free from combustible materials, gasoline and other flammable vapors and liquids.

•  This outdoor fire pit is NOT to be operated by children.

•  This outdoor fire pit is NOT to be used in or on boats or recreational vehicles.

•  Do NOT connect to a remote gas supply.

•  Never attempt to attach this outdoor fire pit to the self-contained LP gas system of a camper trailer, motor home or house.

• Always use in accordance with all applicable local, state and national codes. Contact your local fire department for details on outdoor burning. W When using this outdoor fire pit, exercise the same precautions you would with any open fire.

• Do NOT burn solid fuels such as: wood, charcoal briquettes, lump charcoal, manufactured logs, driftwood, trash, leaves, paper, cardboard, plywood, painted/stained/pressure treated wood in this outdoor fire pit.

•  It is essential to keep the outdoor fire pit’s valve compartment, burners, and circulating air passages clean. Inspect outdoor fire pit before each use.

•  Do NOT use this outdoor fire pit until it is COMPLETELY assembled and all parts are securely fastened and tightened.

•  Do NOT use this outdoor fire pit near automobiles, trucks, vans or recreational vehicles.

•  Do NOT use this outdoor fire pit under any overhang or near any unprotected combustible constructions. Avoid using near or under overhanging trees and shrubs.

•  Always use this outdoor fire pit on a hard, level, non-combustible surface such as concrete, rock or stone. An asphalt or blacktop surface may not be acceptable for this purpose.

•  Do NOT use this outdoor fire pit for cooking.

•  Do NOT use this appliance if any part has been under water.
  Immediately call a qualified service technician to inspect the appliance and to replace any part or control system and any gas control which has been under water.

•  Do NOT wear flammable or loose clothing when operating this outdoor fire pit.

• Do NOT use in windy conditions.

•  Never lean over this outdoor fire pit when lighting or when in use. W Do NOT use this outdoor fire pit unless burner is securely in place. W Keep all electrical cords away from this outdoor fire pit during use. W Certain areas of this outdoor fire pit when in use will become too hot to touch. To avoid burns, do NOT touch hot surfaces until the unit has completely cooled (about 45 minutes), unless you are wearing protective gear (such as insulated pot holders or heat-resistant gloves/mittens).

•  Do NOT leave a lit outdoor fire pit unattended, especially around children and pets.

• Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns or clothing ignition.

•  Young children should be carefully supervised when they are in the area of the appliance.

•  Do NOT hang or place clothing or other flammable material on or near this appliance.

•  Any guard or other protective device removed for servicing the appliance must be replaced prior to operating the appliance.

•  If applicable, protective cover must be removed when burner is in operation.

•  Do NOT attempt to move outdoor fire pit when in use. Allow the outdoor fire pit to cool before moving or storing.

•  This outdoor fire pit should be thoroughly cleaned and inspected on a regular basis. Clean and inspect the hose before each use of the appliance. If there is evidence of abrasion, wear, cuts, or leaks, the hose must be replaced prior to the appliance being operated.

•  This outdoor fire pit should be inspected at least annually by a qualified service person. Depending on amount of use, more frequent cleaning may be required. Do NOT operate until all parts have been repaired or replaced.

•  Use only the regulator and hose assembly provided. Use only the replacement regulator and hose assembly specified by Mr. Bar-B-Q Products LLC.

• Use only Mr. Bar-B-Q Products LLC factory-authorized parts. The use of any part that is not factory-authorized can be dangerous and will void your warranty.

•  Use only Mr. Bar-B-Q Products LLC factory-authorized fire glass /lava rock. The use of any fire glass/lava rock that is not factory-authorized can be dangerous and will void your warranty.

•  Do NOT operate this appliance without reading “Operating Instructions” in this manual.

•  Storage of this outdoor fire pit indoors is permissible only if the tank is disconnected, removed from the outdoor fire pit and properly stored outdoors.

• Do NOT attempt to disconnect the gas regulator from the tank or any gas fitting while the outdoor fire pit is in use.

• If the outdoor fire pit is not in use, the gas must be turned off at the supply tank.

CAUTION: The gas pressure regulator provided with this appliance must be used. This regulator is set for an outlet pressure of 11 inches water column.

•  The minimum inlet gas pressure for this outdoor fire pit is 11 inches of water column, for the purpose of input adjustment.
• The maximum inlet gas pressure for this outdoor fire pit is 11 inches of water column.
•  Before pressure testing, close LP gas tank valve and disconnect gas regulator. The gas supply piping system must test at pressures equal to or less than 1/2 psi (3.5 kPa).
• Do NOT sit or stand on the mantle or any part of this appliance.
•  Do NOT throw anything onto the fire when the unit is in operation.
• Fire glass/lava rock are very hot. Keep children or pets at a safe distance from this appliance.
•  When heated, lava rock/fire glass may pop.
•  The opening of the tank collar should face toward the door side for easy access.
•  Do NOT store any combustible materials in the base enclosure.
•  Use protective gloves when assembling this product.
•  Do NOT force parts together as this can result in personal injury or damage to the product.
•  Death, serious injury or damage to property may occur if the above is not followed exactly.

Parts List

1

| Black Fire Glass| GLS-BLK
---|---|---
2| Table Insert| 58-24-573
3| Bowl Assembly| 58-24-317
4| Igniter Cover| 58-24-318
5| Burner| 58-24-319
6| Control Knob| 58-23-139
7| Battery Cap| 58-23-897
8| Regulator/Hose Assembly*|

58-24-320

9| Mantel| 58-24-574
10| Side Panel (2)| 58-24-322
11| Rear Panel| 58-24-323
12| Leg A| 58-24-324
13| Leg B| 58-24-325
14| Leg C| 58-24-326
15| Leg D| 58-24-327
16| Magnet (2)| 58-24-328
17| Door| 58-24-329
18| Door knob| 58-24-330
19| Foot (4)| 58-24-331
20| Base| 58-24-332
21| LP Gas Tank Retainer Bolt| 58-23-149
22| Cover| 58-24-333
23| Lava Rock (not required and sold separately)**|

55-05-833

• Pre-assembled

CAUTION: Use only Mr. Bar-B-Q Products LLC factory-authorized fire glass/lava rock. The use of any fire glass/lava rock that is not factory- authorized can be dangerous and will void your warranty.

WARNING
When heated, lava rocks may react by breaking and throwing fragments of rock. Be sure to season the lava rocks at a high temperature before use in order to avoid potential personal injury or damage.

IMPORTANT BEFORE USE

HOW TO SEASON LAVA ROCK ON PAGE 8.
How to light an electronic ignitor https://youtu.be/aFWb1YYnRo0

Hardware Pack 58-24-334

Expanded View

Sold Separatel

Tools Required for Assembly (Not Included)

2 Phillips Head Screwdriver

Assembly Instructions

DO NOT RETURN TO PLACE OF PURCHASE.
For or assistance, call 1.888.398.86431.888.398.8643 toll-free toll-free.. Please ha Please have your your owner’s manual and model number as manual and model number available for for reference..
Note: The model number is printed on a label which can be found on The model number is printed on a label which can be found on the inside doorthe inside door,, back or side of the base assembly back or side of the base assembly..

Assembly  Tips:

1.  Select an area where you will assemble this produc tSelect an area where you will assemble this product.. Too protect components, protect components, choose a smooth surface tha choose a smooth surface that’s free of free of cracks or openings cracks or openings..
2.  Spread out all parts Spread out all parts..
3. . Tighten all hardware connections by hand first tighten all hardware connections by hand first.. Then, before before completing each step, completing each step, go back and fully tighten all hardware go back and fully tighten all hardware.. Be careful not to over Be careful not to over-tighten-tighten.. That could damat could damage surfaces or surfaces or strip thread strip threads..
4.  For best results, or best results, complete each step in the order presented complete each step in the order presented.. To complete assembly you will need:

• Leak detection solution (instructions on ho(1) Leak detection solution (instructions on how to make the to make the solution are in solution are included in the included in the “Operating Instructions”  section of section of this manual)this manual)..
•  Precision-filled LP gas grill tank with (1) Precision-filled LP gas grill tank with Acme Acme Type 1 externa1 external threaded valve connection (standard grill size) (not threaded valve connection (standard grill size) (not included) included)..

Typical assembly is a Typical assembly is approximately one hour one hour..
CAUTION:   Two (2) people will be required for assembly (2) people will be required for assembly..
WARNING: Failure to position the parts in accordance with to position the parts in accordance with these diagrams or these diagrams or failure to use only parts specifically failure to use only parts specifically approved with this appliance may result in property damage with this appliance may result in property damage or personal injury.

Attach Legs

CAUTION: Two (2) people will be required to turn the outdoor fire pit over.

• To avoid scratches choose a smooth surface that’s free of cracks or openings.

Note: Do not fully tighten screws until step 4.

Attach Side and Rear Panels
Note: Attach bottom screws before attaching top screws. Do not fully tighten srews until step 4.
Attach Base
Note: Tighten screws from steps 2 and 4.
Attach Door and Turn Outdoor Fire Pit Over
CAUTION: Two (2) people will be required to turn the outdoor fire pit upright on feet.
Insert Battery
Note: Remove plastic wrapper before installing battery
Place Fire Glass – Wear protective gloves

CAUTION: Do NOT dump fire glass out of package. Carefully place fire glass by hand so dust does not clog burner.

• Wear protective gloves.
• Use only Mr. Bar-B-Q Products LLC factory- authorized fire glass. The use of any fire glass that is not factory-authorized can be dangerous and will void your warranty.
•  Do NOT cover pilot housing.

Note: Fire glass should be 0.8-2.0 in. (2-5 cm) long. Approx. 8.8 lbs (4 kgs) of fire glass are needed.
Place Table Insert
WARNING: NEVER place table insert on outdoor fire pit while in use.

• NEVER place table insert on outdoor fire pit while the outdoor fire pit is still hot.
  

IMPORTANT BEFORE USE
HOW TO SEASON LAVA ROCK

1.  Place the lava rocks into the fire pit bowl before turning on.
2. Follow the lighting instructions from the owner’s manual to light the fire pit.
3. Turn the fire pit to the highest heat.
4. Allow the lava rocks to heat at the maximum temperature for 30 minutes 1111before enjoying fire pit.
5. Keep all people and any material that could burn at least 15 feet away from the 1111fire pit while the lava rocks are being seasoned.
6. Repeat the process if your fire pit has been exposed to rain or moisture. 7. Keep your fire pit covered when not in use.

OPTIONAL ITEM SOLD SEPARATELY

Place Lava Rocks – Wear protective gloves
CAUTION: When switching from fire glass, remove all fire glass before placing lava rock. CAUTION: Do NOT dump lava  rocks out of package. Carefully place lava rocks by hand so dust does not clog burner.

• Wear protective gloves.
•  Use only Mr. Bar-B-Q Products LLC. factory- authorized lava rock. The use of any lava rock that is not factory-authorized can be dangerous and will void your warranty.
•  Do NOT cover igniter cover.

Note: Lava rocks should be 0.8-2.0 in. (2-5 cm) long. Approx. 3.74 lb (1.7 kg) of lava rocks are needed.

Installing LP Gas Tank

To operate, you will need one precision-filled standard grill LP gas tank with external valve threads.
CAUTION: LP gas tank must be properly disconnected and removed prior to moving this outdoor fire pit.

Inserting LP Gas Tank

WARNING: Make sure LP gas tank valve is closed.

1. Open door.
2.  Make sure the control knob is in the “ OFF” position (Figure 3).
3. Loosen LP gas tank retainer bolt by turning counter-clockwise.
4. Place precision-filled LP gas tank upright into hole in outdoor fire pit base so the tank valve is facing the gas line connection.
5. Secure tank by turning LP gas tank retainer bolt clockwise until tight.
6. Close door.
   

Connecting LP Gas Tank

1. Make sure the control knob is in the “ OFF” position  (Figure 3).
2. Before connecting, be sure there is no debris caught in the  head of the LP gas tank, head of the regulator valve or in the head of the burner or burner ports.
3. Connect regulator/hose assembly to tank by turning knob clockwise until it stops.
4. Perform leak check per “Checking for Leaks” section.

Disconnecting LP Gas Tank

1.  Make sure the control knob is in the “ OFF” position  (Figure 3).

2. Before disconnecting, make sure the LP gas tank valve is “CLOSED.”

3. Disconnect regulator/hose assembly from LP gas tank by turning knob counterclockwise until it is loose.
   CAUTION: LP gas tank must be properly disconnected and removed prior to moving this fire pit.

4. Place the protective cap cover on the LP tank and store the tank outdoors in a well ventilated area out of direct sunlight.

Operating Instructions

Checking for Leaks
WARNING: Before using this outdoor fire pit, make sure you have read, understand and are following all information provided in the “Important Safeguards” section
on page 2. Failure to follow those instructions can cause death, serious injury or property damage.

•  The burner must be replaced prior to the appliance being put into operation if it is evident that the burner is damaged. The replacement burner shall be that specified by the manufacturer.

Burner Connections

1. Make sure the regulator hose and valve connections are securely fastened to the burner and the tank.

2. Visually check the connection between the burner/venturi tube and orifice.

3.  Make sure the burner/venturi tube fits over the orifice.
   WARNING: Failure to inspect this connection or follow these instructions could cause a fire or an explosion which can cause death, serious bodily injury or damage to property.

4. Please refer to diagram for proper installation

5. . If the burner/venturi tube does not rest flush to the orifice, as shown, please contact 1.888.398.8643 for assistance.

Tank/Gas Line Connection

1. Make 2-3 oz. of leak detection solution by mixing one part liquid dishwashing soap with three parts water.
2. Make sure control knob is in the “ OFF”  position .
3. Connect LP gas tank per “Installing LP Gas Tank” section.
4.  Turn LP gas tank valve to “OPEN.”
5. Spoon several drops of solution, or use a squirt  bottle, at all “X” locations (Figures 1 and 2).

• If any bubbles appear, turn LP gas tank valve to “CLOSED,” reconnect and re-test.
• If you continue to see bubbles after  several attempts, turn LP gas tank valve to “CLOSED” and disconnect LP gas tank, per “Disconnecting LP Gas Tank” section. Contact 1.888.398.8643 for assistance.
• If no bubbles appear after one minute, turn LP gas tank valve to “CLOSED,” wipe away solution and proceed.

Lighting
DANGER: Failure to follow these lighting instructions may result in serious bodily injury or death, or in a fire or an explosion causing damage to property.
WARNING: NEVER light the burner with the cover on the outdoor fire pit.
CAUTION: Keep outdoor gas appliance area clear and free from combustible materials, gasoline and other flammable vapors and liquids.

• Do NOT obstruct the flow of combustion and ventilation air. W CAUTION: Check and clean burner/venturi tubes for insects and insect nests. A clogged tube can lead to a fire.

1. Make sure all labels, packaging and protective films have been removed from the outdoor fire pit.

2.  Check for obstructions of airflow to the burner. Spiders, insects and webs can clog the burner/venturi tube. A clogged burner tube can lead to a fire.

3.  Make sure control knob is in the “ OFF” position (Figure 3).

4. Clear small area of lava rocks / fire glass away from the igniter cover.

5. Connect LP gas tank per “Installing LP Gas Tank” section.

6. Slowly turn LP gas tank valve 1 revolution to “OPEN.”

7. Push and turn control knob to (HIGH). Continue to hold the control knob in to light.

8. After the fire pit lights, continue to hold the control knob in for 20 seconds to heat the thermocouple, a safety device that stops the gas flow when a firepit is not lit. Holding the knob in for 20 seconds warms it up so the gas flow will continue.

9. After 20 seconds, release and turn control knob counterclockwise to adjust flame to desired height.

10.  After three attempts, if ignition does not occur, turn the burner control knob to “

11. Wait 5 minutes, fan with a newspaper or magazine, and repeat lighting procedure.

12. If igniter does not light burner:

    • Wearing heat-resistant gloves, position a lit long match or lit long butane lighter near the pilot housing.
    • Push and turn control knob to (HIGH).
    • Remove match/lighter once burner is lit.
      CAUTION: After lighting – using a fire pit tool and heat-resistant gloves, carefully move the fire glass/lava rock back to their proper position, being careful to avoid the flame.

13. After lighting, observe the burner flame. Make sure all burner ports are lit and flame height matches illustration .

CAUTION: If ignition does not occur in 5 seconds, turn control knob to “ OFF,” wait 5 minutes, fan with a newspaper or magazine, and repeat lighting procedure.

Turning Off

1.  Turn LP gas tank valve to “CLOSED.”
2. Turn control knob to the “ OFF” position.

Note: A “poof” sound is normal as the last of the LP gas is burned. 3. Disconnect LP gas tank per “Disconnecting LP Gas Tank” section.

Cleaning and Care

CAUTION:

1. All cleaning and maintenance should be done when outdoor fire pit is cool and with the fuel supply disconnected.
2. Do NOT clean any outdoor fire pit part in a self-cleaning oven. The extreme heat will damage the finish.
3. Do NOT enlarge valve orifices or burner ports when cleaning the valves or burners.
4. All components on this outdoor fire pit can become hot.
5.  Do NOT clean this outdoor fire pit until all components are cool.

Notices

1. This outdoor fire pit should be thoroughly cleaned and inspected on a regular basis.
2. Abrasive cleaners will damage this product.
3. NEVER use oven cleaner to clean any part of this outdoor fire pit.

Before Each Use:

1.  Keep the outdoor fire pit area clear and free from any combustible materials, gasoline, and other flammable vapors and liquids.
2.  Do NOT obstruct the flow of the combustion of LP gas and the ventilation of air.
3. Keep the ventilation opening(s) of the LP gas tank area free and clear from debris.
4. Visually check the burner flames to make sure your outdoor fire pit is working properly (Figure 5).
5. See below for proper cleaning instructions.
6. Check all gas connections for leaks.
7.  Check components for any signs of damage or rust.
8. Check for obstructions of airflow to the burner. Spiders, insects and webs can clog the burner/venturi tube. A clogged burner/venturi tube can lead to a fire.
9. If damage to any component is detected, do NOT operate until repairs are completed.

Cleaning Surfaces

1.  Wipe surfaces clean with mild dishwashing detergent or baking soda mixed with water.
2. For stubborn stains, use a citrus-based cleaner and a nylon scrubbing brush.
3. Rinse clean with water.
4. Allow to air dry.

Cleaning Burner
WARNING: All cleaning should be done when appliance is cool and with the fuel supply disconnected per “Disconnecting LP Gas Tank.”

1. Remove the fire glass/lava rock.

2. Remove all dirt/dust from the burner, igniter cover and venturi area with a small brush and/or compressed air.

3. Visually inspect the burner for any rust or damage. If damage is found, replace necessary parts with new from the manufacturer.

4. Clean any clogged burner ports with a stiff wire (such as an opened paper clip).

5. Carefully replace the fire glass/lava rock being cautious not to block the igniter cover.

Before Storing

1. Turn LP gas tank valve to “CLOSED.”

2. Turn control knob to the “ OFF” position.
   Note: A “poof” sound is normal as the last of the gas is burned.

3. Disconnect LP gas tank per “Disconnecting LP Gas Tank” section.

4. Clean all surfaces.

5.  Lightly coat the burner with cooking oil to prevent excess rusting.
   CAUTION: NEVER place cover on hot outdoor fire pit.

6. If storing the outdoor fire pit indoors, cover the outdoor fire pit and store in a cool dry location away from children and pets.

7.  If storing the outdoor fire pit outdoors, cover the outdoor fire pit with a cover for protection from the weather.

Product Registration

For faster warranty service, please register your product immediately. To register, email registration@mrbarbq.com with your name, address, phone number and copy of your receipt or call 1.888.398.8643.

Replacement Parts
For replacement parts, call 1.888.398.8643.

Limited Warranty

Mr. Bar-B-Q Products LLC warrants to the original retail purchaser of this product, and to no other person, that if this product is assembled, maintained, and operated in accordance with the printed instructions accompanying it, then for a period of one (1) year from the date of purchase, all parts in such product shall be free from defects in material and workmanship. Mr. Bar-B-Q Products LLC may require reasonable proof of your date of purchase. Therefore, you should retain your sales slip or invoice. This Limited Warranty shall be limited to the repair or replacement of parts, which prove defective under normal use and service and which Mr. Bar-B-Q Products LLC shall determine in its reasonable discretion upon examination to be defective. Before returning any parts, you should contact Mr. Bar-B-Q Products LLC Customer Care Department using the contact information listed below. If Mr. Bar-B-Q Products LLC confirms, after examination, a defect covered by this Limited Warranty in any returned part, and if Mr. Bar-B-Q Products LLC approves the claim, Mr. Bar-B-Q Products LLC will replace such defective part without charge. If you return defective parts, transportation charges must be prepaid by you. Mr. Bar-B-Q Products LLC will return replacement parts to the original retail purchaser, freight or postage prepaid. This Limited Warranty does not cover any failures or operating difficulties due to accident, abuse, misuse, alteration, misapplication, improper installation or improper maintenance or service by you or any third party, or failure to perform normal and routine maintenance on the product as set out in this owner’s manual. In addition, the Limited Warranty does not cover damage to the finish, such as scratches, dents, discoloration, rust or other weather damage, after purchase. This Limited Warranty is in lieu of all other express warranties. Mr. Bar-B-Q Products LLC disclaims all warranties for products that are purchased from sellers other than authorized retailers or distributors, including the warranty of merchantability or the warranty of fitness for a particular purpose. Mr. Bar-B-Q Products LLC ALSO DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Mr. Bar-B-Q Products LLC SHALL HAVE NO LIABILITY TO PURCHASER OR ANY THIRD PARTY FOR ANY SPECIAL, INDIRECT, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. Mr. Bar-B-Q Products LLC further disclaims any implied or express warranty of, and assumes no responsibility for, defects in workmanship caused by third parties. This Limited Warranty gives the purchaser specific legal rights; a purchaser may have other rights depending upon where he or she lives. Some jurisdictions do not allow the exclusion or limitation of special, incidental or consequential damages, or limitations on how long a warranty lasts, so the above exclusion and limitations may not apply to everyone. Mr. Bar-B-Q Products LLC does not authorize any person or company to assume for it any other obligation or liability in connection with the sale, installation, use, removal, return, or replacement of its equipment, and no such representations are binding on
Mr. Bar-B-Q Products LLC.
Mr. Bar-B-Q Products LLC
10 Hub Dr., Ste 101, Melville, NY 11747 USA
1.888.398.8643

Troubleshooting

Problem Possible Cause Prevention/Cure

Burner will not light using igniter| LP gas tank valve is closed| Make sure regulator is securely attached to the LP gas tank per “Installing LP Gas Tank,” then turn LP gas tank valve to “OPEN”
LP gas tank is low or empty| Exchange, refill or replace LP gas tank
LP gas leak|

1. Turn LP gas tank valve to “CLOSED”
2. Wait 5 minutes for gas to clear
3.  Follow “Checking for Leaks” section

Battery needs to be changed| Replace the “AA” battery (follow assembly step for inserting battery)
Electrode and burners are wet| Wipe dry with cloth
Electrode cracked or broken – sparks at crack| Replacement part(s) may be needed – contact Customer Care at 888 .398 .8643
Wire loose or disconnected| Reconnect wire or replacement part(s) may be needed – contact Customer Care at 888 .398 .8643
Wire is shorting (sparking) between igniter and electrode| Replacement part(s) may be needed – contact Customer Care at 888 .398 .8643
Thermocouple is not operating correctly|

1.  Disconnect LP Gas tank per “Disconnect LP Gas Tank” section .
2. Clean area around thermocouple .
3.  Connect LP gas tank per “Connect LP Gas Tank” section .
4. Relight per “Lighting” section .
5.  If the outdoor fire pit is still not working, please contact Customer Care at 888 .398 .8643 for additional assistance .

Bad igniter| Replacement part(s) may be needed – contact Customer Care at 888 .398 .8643
Burner will not light with match| No gas flow| Check if LP gas tank is empty

a . If empty, exchange, refill or replace LP gas tank
b . If LP gas tank is not empty, refer to “Sudden drop in gas flow or reduced flame height” (see below)

LP gas tank is low or empty| Exchange, refill or replace LP gas tank

LP gas leak

|

1.   Turn LP gas tank valve to “CLOSED”
2.    Wait 5 minutes for gas to clear
3.  Follow “Checking for Leaks” section

Coupling nut and regulator not fully connected| Turn the coupling nut about one-half to three-quarters additional turn until solid stop . Tighten by hand only – do NOT use tools.
Obstruction of gas flow|

1.  Clear burner/venturi tube
2. Check for bent or kinked hose

Disengagement of burner to valve| Re-engage burner and valve
Spider webs or insect nest in burner/venturi tube| Clean burner/venturi tube
Thermocouple is not operating correctly|

1.   Disconnect LP Gas tank per “Disconnect LP Gas Tank” section .
2.  Clean area around thermocouple .
3.  Connect LP gas tank per “Connect LP Gas Tank” section .
4. Relight per “Lighting” section .
5.  If the outdoor fire pit is still not working, please contact Customer Care at 888 .398 .8643 for additional assistance .

Burner ports clogged or blocked| Clean burner ports
Sudden drop in gas flow or reduced flame height| Out of gas| Exchange, refill or replace LP gas tank
Overfilling prevention device may have been activated|

1.  Turn control knob to “ OFF”
2. Wait 30 seconds and light outdoor fire pit per “Lighting” section
3.   If flames are still too low, reset the overfilling prevention device:

a .  Turn control knob “ OFF”
b .  Turn LP gas tank valve to “CLOSED”
c .  Disconnect LP gas tank from regulator
d .  Turn control knob to (HIGH)
e . Wait two minutes
f .  Turn control knob to “ OFF”
g .  Reconnect LP gas tank to regulator and leak check connections, being careful not to fully open valve
h .  Light outdoor fire pit per “Lighting” section

Irregular flame pattern, flame does not run the full length of burner| Burner ports are clogged or blocked| Clean burner ports
Flame is yellow or orange| New burner may have residual manufacturing oils| Burn outdoor fire pit for 15 minutes and reinspect
Spider webs or insect nest in burner/venturi tube| Clean burner/venturi tube
Poor alignment of valve to burner/venturi tube| Ensure burner/venturi tube is properly engaged with valve
Flame goes out| High or gusting winds| Do not use outdoor fire pit in high winds
Low on LP gas| Exchange, refill or replace LP gas tank
Excess flow valve tripped| Refer to “Sudden drop in gas flow or reduced flame height”
Thermocouple is not operating correctly|

1. Disconnect LP Gas tank per “Disconnect LP Gas Tank” section .
2.  Clean area around thermocouple .
3.  Connect LP gas tank per “Connect LP Gas Tank” section .
4.   Relight per “Lighting” section .
5. If the outdoor fire pit is still not working, please contact Customer Care at 888 .398 .8643 for additional assistance .

Flashback (fire in venturi/burner tube(s))| Burner and/or burner/venturi tube is blocked| Clean burner and/or burner/venturi tube
Flame seems to lose heat when burning in cold weather – temperature below 50ºF| Ice has built up on the outside of the LP gas tank because the vaporization process is too slow|

1. Turn off per “Turning Off” section
2.   Replace with a spare LP gas tank
3.  Reconnect LP gas tank per “Installing LP Gas Tank” section
4. Follow “Checking for Leaks” section
5.  Light outdoor fire pit per “Lighting” section

For assistance, please visit us at MrBarBQProducts.com or call 1.888.398.8643.

References

• Mr. Bar-B-Q Products LLC – Everything for the Grill

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>