mitzi H888101 Aston 5 Chandelier Light Instruction Manual
- June 1, 2024
- mitzi
Table of Contents
mitzi H888101 Aston 5 Chandelier Light
Specifications:
- Brand : Mitzi
- Model : YAEL H888101
- Fixture Type: Pendant Light
- Maximum Wattage: 15 Watts (Type G25 Lamp)
Product Usage Instructions
Fixture Installation:
- Attach the MOUNTING PLATE (A) onto the junction box using the MOUNTING SCREWS (B). Ensure the junction box is securely mounted to the building structure.
- Connect the Ground wire (Green) to the ground inside the outlet box or the GROUND SCREW (C) on the MOUNTING PLATE (A). Never connect ground wire to hot wire to prevent injury or death.
- Connect the white fixture lead to the neutral wire in the outlet box using an approved fastener (WIRE NUT) (D). Secure the connection with electrical tape to prevent short circuits.
- Connect the black fixture leads to the hot wire in the junction box, ensuring proper fastening. Never reverse hot and neutral wire to avoid injury or death.
- Attach the FIXTURE ASSEMBLY (F) to the MOUNTING PLATE (A) and secure with FIXTURE MOUNTING SCREWS (E).
- Lift METAL SHADE (G) to the FIXTURE ASSEMBLY (F) and secure with the RING (H).
- Screw the BULB (I) into the SOCKET of the fixture. Use a max 15-watt Type G25 lamp and avoid exceeding recommended wattage.
- Restore power to the outlet at the breaker or fuse box.
Frequently Asked Questions:
- Q: Can I use a higher-wattage bulb than recommended?
- A : No, it is important to follow the recommended maximum wattage (15 watts, Type G25 lamp) to prevent damage to the fixture.
- Q: What should I do if I encounter exposed wire during installation?
- A: Ensure there are no exposed wires or strands that could cause a short circuit. Properly insulate any exposed wires with electrical tape before proceeding with the installation
- Q: Is it necessary to secure the metal shade with the ring?
- A: Yes, it is essential to secure the metal shade with the ring provided to ensure the stability and safety of the fixture.
WARNING/CAUTION
DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION. · TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURES MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED FACTORY-TRAINED TECHNICIAN. · CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER USE. · UNPACK FIXTURE, PARTS AND PARTS BAG(S) BEFORE DISCARDING THE CARTON. MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE PRIOR TO INSTALLATION FOR ANY DAMAGE. HVLG DOES NOT PAY OR REIMBURSE ELECTRICIAN FEES.
FIXTURE MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED. SEE WARRANTY FOR EXCEPTIONS. · PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS.
FIXTURE INSTALLATION
- Attach the MOUNTING PLATE (A) onto the junction box using the MOUNTING SCREWS (B). Thisfixture is designed to be mounted on a standard round or octagon junction box. The junction box must be securely mounted to the structure of the building.
- Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bar copper wire) or the GROUND SCREW (C) on the MOUNTING PLATE (A). NEVER CONNECT GROUND WIRETO “HOT” WIREĞ FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH
- Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wire together with an approved fastener (WIRE NUT) (D). Starting 1″ below the fastener, tightly wrap the connection with electrical tape so that the connection seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED WIRES OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT
- Connect the black fixture leads to the hot (Generally black) wire in the junction box. Fasten the joined wires same as the previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW COULD RESULT IN SERIOUS IN URY OR DEATH
- Attach the FIXTURE ASSEMBLY (F) to the MOUNTING PLATE (A) and secure with the FIXTUREMOUNTING SCREWS (E).
- Lift METAL SHADE (G) up to the FIXTURE ASSEMBLY (F) and secure with the RING (H).7. Screw the BULB (I) into the SOCKET of the fixture. THIS FIXTURE IS RATED FOR A MAX 15-WATT TYPEG25 LAMP. DO NOT EXCEED THE RECOMMENDED WATTAGE. Restore power to the outlet at the breaker or fuse box.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>