mitzi H481701S Whitley 1 Light Polished Nickel Pendant Ceiling Instruction Manual

June 8, 2024
mitzi

WHITLEY
H481701S, H481701L
INSTALLATION INSTRUCTIONSmitzi H481701S Whitley 1 Light Polished Nickel
Pendant Ceiling

H481701S Whitley 1 Light Polished Nickel Pendant Ceiling

ITEM DESCRIPTION PART NUMBER
1 MOUNTING PLATE HDW-H481701S
2 MOUNTING SCREW HDW-H481701S
3 GROUND SCREW HDW-H481701S
4 WIRE NUT HDW-H481701S
5 SWIVEL/HANG STRAIGHT CAS-H481701S
6 BALL NUT HDW-H481701S
7 CANOPY CAS-H481701S
8 16 mm DIA- HVM STEM KIT 3″+6″+12″+18″ STM-ZH1300, ZH1600
9 FIXTURE ASSEMBLY FAS-H481701S, 701L
10 METAL SHADE SHD-H481701S, 701L
11 SOCKET RING RNG-H481701S
12 BULB NOT INCLUDED

WARNING/CAUTION

  • DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.
  • TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL  ELECTRICAL/BUILDING CODES. THE INSTALLATION AND MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED  ELECTRICIAN OR CERTIFIED FACTORY TRAINED TECHNICIAN.
  • CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH  DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER USE.
  • REMOVE THE FIXTURE, PARTS AND PARTS BAG(S) FROM THE CARTON. BEFORE DISCARDING THE CARTON, DOUBLE CHECK TO MAKE  CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE PRIOR TO INSTALLATION FOR ANY DAMAGE TO THE FIXTURE.
  • DIMMING: THE FIXTURE CAN BE CONTROLLED BY A WALL DIMMING DEVICE. ONLY USE TRIAC/ELECTRONIC DIMMER. MAKE SURE THE  CARTON IS MARKED FOR USE WITH LED COMPACT FLUORESCENT-INCANDESCENT LIGHT SOURCE ONLY. THESE CAN BE PROVIDED BY  YOUR LOCAL ELECTRICAL DISTRIBUTOR, HOME CENTER, OR HARDWARE STORE.
  • PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS

FIXTURE INSTALLATION

  1. Feed the wire through the STEM (8) and twist tightly onto the FIXTURE ASSEMBLY (9). Keep adding additional stems until you desired hanging height is met.

  2. Slide in CANOPY(7 ) onto the STEM (8), and thread the SWIVEL (5) onto the top end of the STEM (8)

  3. Pull the wire out from the junction box, and install the MOUNTING PLATE (1) onto the junction box using the MOUNTING SCREWS (2). This fixture is designed  to be mounted on standard round or octagon junction box.
    The junction box must be securely mounted to the structure of the building.

  4. Trim off the excess wire to a minimum 6″ beyond the STEM and strip each wire 5 8″.

  5. Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bar copper wire) or the GROUND SCREW (3) on the MOUNTING PLATE  (1). NEVER CONNECT GROUND WIRE TO “HOT” WIRE! FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!

  6. Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together with an approved fastener (WIRE NUT) (4). Starting 1″  below the fastener, tightly wrap the connection with electrical tape so that the connections seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT!

  7. Connect the black fixture leads to the hot (Generally black) wire in the outlet box. Fasten the joined wires same as previous step. NEVER REVERSE HOT AND  NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!

  8. Push the wires back into the junction box. Lift up the CANOPY (7) up to the ceiling, and secure with the BALL NUTS (9).

  9. Lift the METAL CAP(10) up and secure it with the SOCKET RING(11).

  10. Push the BULB (12) up into the sockets of the fixture. THIS FIXTURE IS RATED FOR 8 WATT LAMP. DO NOT EXCEED THE RECOMMENDED WATTAGE!

  11. Restore power to the outlet at the breaker or fuse box.

Questions? We’re here to help!
Contact us at CustomerService@hvlgroup.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals