mitzi SIA H883102 Corinthia 10 Wide Pendant Instruction Manual

Table of Contents

Specifications

Fixture Installation

Attach the Mounting Plate (A) to the junction box using the Mounting Screws (B).
Connect the Ground wire (Green) to the ground inside the outlet box or Ground Screw (C).
Connect the white fixture lead to the neutral wire in the outlet box using a Wire Nut (D).
Connect the black fixture leads to the hot wire in the junction box.
Attach the Fixture Assembly (F) to the Mounting Plate (A) and secure with Fixture Mounting Screws (E).
Screw the Bulb (G) into the socket of the fixture (Max 8W Type G16.5 lamp).
Screw Glass A (H) into the Fixture Assembly (F).
Restore power at the breaker or fuse box.

Can I use a bulb with a wattage higher than 8W?
No, it is recommended not to exceed the maximum wattage of 8 watts for Type G16.5 lamp for safety reasons.
What should I do if I encounter exposed wires during installation?
If you find exposed wires during installation, do not proceed with the connection. Ensure all wires are properly insulated to avoid any potential short circuits.
Can I install this fixture on any type of junction box?
This fixture is designed to be mounted on standard round or octagon junction boxes for proper installation.

WARNING/CAUTION

DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.
TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURES MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED FACTORY-TRAINED TECHNICIAN.
CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER USE.
UNPACK FIXTURE, PARTS AND PARTS BAG(S) BEFORE DISCARDING THE CARTON. MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE PRIOR TO INSTALLATION FOR ANY DAMAGE. HVLG DOES NOT PAY OR REIMBURSE ELECTRICIAN FEES. FIXTURE MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED. SEE WARRANTY FOR EXCEPTIONS.
PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS.

mitzi-SIA-H883102-Corinthia-10-Wide-Pendant-fig-2

FIXTURE INSTALLATION

Attach the MOUNTING PLATE (A) to the junction box using the MOUNTING SCREWS (B). This fixture is designed to be mounted on a standard round or octagon junction box. The junction box must be securely mounted to the structure of the building.
Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bare copper wire) or the GROUND SCREW (C) on the MOUNTING PLATE (A). NEVER CONNECT GROUND WIRE TO “HOT” WIRE! FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together with an approved fastener (WIRE NUT) (D). Starting 1″ below the fastener, tightly wrap the connection with electrical tape so that the connections seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED WIRES OR STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT!
Connect the black fixture to the hot (Generally black) wire in the junction box. Fasten the joined wires the same as in the previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
Attach the FIXTURE ASSEMBLY (F) to the MOUNTING PLATE (A) and secure with the FIXTURE MOUNTING SCREWS (E).
Screw the BULB (G) into the SOCKET of the fixture. THIS FIXTURE IS RATED FOR MAX 8 WATT TYPE G16.5 LAMP. DO NOT EXCEED THE RECOMMENDED WATTAGE!
Screw the GLASS A (H) into the FIXTURE ASSEMBLY (F) of the fixture.
Restore power to the outlet at the breaker or fuse box.