Mitzi H474501A Tatum Square Ceramic Raw White 1 Light Flush Mount Instruction Manual

June 13, 2024
mitzi

Mitzi H474501A Tatum Square Ceramic Raw White 1 Light Flush Mount

Product Information

The product is a lighting fixture manufactured by Hudson Valley Lighting Group. It belongs to the Mitzi collection and the specific model is TATUM (H50A).

Product Usage Instructions

  1. Begin by installing the mounting plate (A) using the provided mounting screws (B).
  2. Ensure that the ground screw (C) is securely connected to the mounting plate (A). Never connect the ground wire to the hot wire to prevent serious injury or death.
  3. Use a wire nut (D) to connect the wires, making sure there are no exposed wires or strands that could cause a dangerous short circuit.
  4. Never reverse the hot and neutral wires as it could result in serious injury or death.
  5. Secure the ceramic ring (E) in place.
  6. Install the recommended 60-watt type G25 lamp (G) into the bulb socket. Do not exceed the recommended wattage.

Replacement Parts

  • MOUNTING PLATE: Part A
  • MOUNTING SCREWS: Part B
  • GROUND SCREW: Part C
  • WIRE NUT: Part D
  • CERAMIC RING: Part E

To purchase replacement parts, refer to the following part numbers:

  • Mounting Plate: HDW-H50A
  • Ceramic Ring: CER-H50A
  • Hardware Kit: RNG-H50A

WARNING/CAUTION

  • DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.
  • TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED FACTORY TRAINED TECHNICIAN.
  • CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER USE.
  • UNPACK FIXTURE, PARTS AND PARTS BAG(S) BEFORE DISCARDING THE CARTON. MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE PRIOR TO INSTALLATION FOR ANY DAMAGE. HVLG DOES NOT PAY OR REIMBURSE ELECTRICIAN FEES. FIXTURE MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED. SEE WARRANTY FOR EXCEPTIONS.
  • PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS.

Installation Instructions

Mitzi-H474501A-Tatum-Square-Ceramic-Raw-
White-1-Light-Flush-Mount-fig-1Mitzi-H474501A-Tatum-Square-Ceramic-Raw-White-1-Light-
Flush-Mount-fig-2

FIXTURE INSTALLATION

  1. Attach the MOUNTING PLATE (A) onto the junction box using the MOUNTING SCREWS (B). This fixture is designed to be mounted on standard round or octagon junction box. The junction box must be securely mounted to the structure of the building.
  2. Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bar copper wire) or the GROUND SCREW (C) on the MOUNTING PLATE (A). NEVER CONNECT GROUND WIRE TO “HOT WIRE! FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
  3. Connect the white fixture lead to the neutral (Generally white wire in the outlet box. Fasten the wires together with an approved fastener (WIRE NUT) (D). Starting I* below the fastener, tightly wrap the connection with electrical tape so that the connections seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT!
  4. Connect the black fixture leads to the hot (Generally black) wire in the junction box. Fasten the joined wires same as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
  5. Lift the CERAMIC (E) up onto the fixture and secure using the RING (F). b.
  6. Screw the BULB (G) up into the SOCKET of the fixture. THIS FIXTURE IS RATED FOR 60 WATT TYPE G25 LAMP. DO NOT EXCEED THE RECOMMENDED WATTAGE!
  7. Restore power to the outlet at the breaker or fuse box.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals