SALLN K-02 Light Stunt Remote Control Car Instruction Manual
- June 12, 2024
- SALLN
Table of Contents
6 + Ages
K-02 Light Stunt Remote Control Car
Instruction Manual
Thank you for purchasing one of our toy products. To ensure that you get the most out of your new purchase, please read these instructions carefully before using the toy for the first time. If you have any questions please contact via email SALLNSERVICE@OUTLOOK.COM
Introduce the Function of the Remote Control and the Vehicle
Instructions:
- Check that the ONIOFF swich s in the “ON” position. The vehicle will not respond to the remote control when the switch OFF/ON is i the “OFF” position.
Charging the batteries
Sketch Map of the Recharging in A Vehicle Battery
Charging diagram of Android USB
charging line
Battery charging
- Connect the USB charger to USB output on computer or AC/DC adaptor, then insert the car charger plug to the USB wire charger. (Make sure in a correct polarity)-Android USB charging line
- A full charge takes 90 minutes. When charging the LED indicator turns into red,when charging is complete, the LED indicator stays off.
- Regularly inspect the toy, battery charger, charging cable, connectors and other components for signs of damage. In the event of any damage, discontinue use and send the parts for repair.
- In case of abnormal responses such as suspicious peculiar smell, noise or smog in the charger,please remove the power supply at once.
- Please recharge with the dedicated USB delivered by the original factory. Never use broken USB or USB of other brands.
- Please do not recharge the swelling, leaking or broken battery.
- Please do not overcharge the battery. When the battery is fully recharged, please pull out the charger.
- Please do not recharge on the surface of the objects near inflammable things(carpet, wood floor,solid wood furniture, etc.) or of conductive things. While recharging, please keep the battery within the range of visibility.
Inserting the remote control batteries
Remote control
- Check the ON/OFF switch is in the “OFF” position.
- Use a screwdriver to loosen the screw.
- Remove the battery cover.
- According the polarity indicated inside in the remote control. Put the 2*AA battery into the battery compartment.
- Put the battery cover back and tighten the screw.
Sketch Map of Installed Battery in
the Remote Control
Remote control car
-
Check the ON/OFF switch is in the “OFF” position.
-
Use a screwdriver to loosen the screw.
-
Remove the battery cover.
-
Install the battery as indicated in the picture on the right:
(1) Connect the rechargeable battery in the battery pack as indicated in the picture.
(2) The version of the AA battery must be guaranteed insert in the correct place. -
Put the battery cover back and tighten the screw.
Sketch Map of Installed Battery in
the Remote Control Vehicle
Using the vehicle
- Switch on the vehicle using the ON/OFF switch.
- Switch on the vehicle ON/OFF switch,make the frequency of the remote control and remote control vehicle match each other,then you can operate the remote control vehicle.
- Switch off the vehicle and remote control after use.
- The playing time is about 20-50+ mins.
- The control rang is about 30 meters, if out of 30 meters rang , it may lose control.
Function and Operaition of the Product
| |
---|---|---
Push both throttle levers upward to make the vehicle move forwards| Push the
right throttle lever upwards to make the vehicel turn left| Push the left
throttle lever downward and right throttle lever upward, the vehicle rotates
towards the left on site
| |
Push both throttle levers downward to make the vehicle move backwards| Push
the left thlottle lever upward to make the vehicle turn right| Push the left
throttle lever upward and right throttle lever downward, the vehicle rotates
towards the right on site
Battery safety Information
- The batteries must only be charged under adult supervision.
- Before charging the batteries, remove the battery compartment from the vehicle chassis.
- Remove empty batteries from the vehicle and remote control.
- Ensure that the vehicle is switched off before inserting the batteries.
- Install the battery according to the instruction inside the battery box. Make sure not to confuse the positive and negative polarity of the battery.
- Do not attempt to charge non-rechargeable batteries.
- Do not short circuit the battery terminals.
- If you do not plan to use the vehicle for an extended period, remove the batteries from the vehicle and remote control to prevent leakage.
- Do not throw batteries into open flames, as this may cause them to explode or leak.
- Do not mix old and new batteries or batteries from different manufacturers.Do not mix alkaline,standard (carbon-zinc,or rechargeable nickel-cadmium) batteries.
- Regularly inspect the batteries for signs of leakage.
**FCC &RSS
**
RSS
CAN ICES—003(BV/NMB—003(B)
This device contains license-exempt transmitter (s)/ Vreceiver (s) that comply
with the Innovation, Science and Economic Development of Canada’s license
exempt RSS(s).
Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Caution: changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be detected by
turning the equipment off and on, the user is encouraged to try to remedy the
interference by one or more of the following measures: Reorient or relocate
the receiving antenna Increase the separation between the equipment and
receiver. Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.Consult the dealer or experienced
radio/TV technician for help.
Product information
| BRAND: | SALLN |
|---|---|
| FREQUENCY: | 2.4GHz |
| PRODUCT NAME: | REMOTE CONTROL CAR |
| MODEL NUMBER: | K-02 |
| FCCID: | 2AL75-TK20220422 |
| BATCH NUMBER: | SALLN-01012023 |
| MANUFACTURER NAME: | SHANTOU SKYTECH TECHNOLOGY INDUSTRIAL INC. |
| MANUFACTURER ADDRESS: | NO.2,WEST XINGYE ROAD,LAIMEI INDUSTRIAL PARK, |
CHENGHATDISTRICT,SHANTOU CITY,GUANGDONG CHINA
DISTRIBUTED BY:| HUNAN YASHENCDIANZI KEJI YOUXIAN CONGSI
DISTRIBUTOR ADDRESS:| 404,BUILDINC 5, DONCHUA VENTURE PARK, NANSHAN STREET,
SHENZHEN, GUANGDONG PROVINCE, CN, 518000
EMAIL:| SALLNSERVICE@OUTLOOK.COM
MADE IN CHINA (CN)
Documents / Resources
|
SALLN K-02 Light Stunt Remote Control
Car
[pdf] Instruction Manual
B0C8TDT6G2, B0BZR414QF, B0C3LWSNLC, K-02, Light Stunt Remote Control Car, K-02
Light Stunt Remote Control Car, Light Stunt Car, Stunt Remote Control Car,
Remote Control Car, Car, Stunt Car
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>