super bright leds PPA401S Wireless Dimming System User Manual

super bright leds PPA401S Wireless Dimming System

Product Information

Specifications

• General Specifications:
  • Operating Temperature: Standard
  • IP Rating: IP20
  • Radio Frequency: 433.96 MHz
  • RF Range: 98.4 ft (30 m)
• WP4013 Specifications:
  • Battery Type: CR2032 (x1 not included)

Product Usage Instructions

Dimming Module (PPA401S) Installation:

1. With supply power off, connect wiring as shown in diagram. Open knockout on fixture or junction box if needed.
2. Mount the dimming module.
3. Follow pairing instructions for the intended controller (dimmer switch, WP4013).

Note: To unpair, hold the PAIR button for 5 seconds. You will hear four beeps to confirm unpairing is complete.
Check the product label for specific electrical specifications related to installation. Improper installation will void the warranty.

Dimming Wires: Multiple lights can be controlled with one dimming module as long as the maximum load (10
A) is not exceeded. Dimming wires can be connected through conduit-side wires or external connector on the controller body, but should not be connected to both simultaneously.

Dimmer Switch (WP4013) Installation:

1. Being careful to avoid any live wires, install the full wall plate or adapter plate with the tab on the bottom side as shown.
2. Install CR2032 battery (not included) into the remote, but do not install remote into the wall plate at this time.
3. With the dimming module powered on, press the PAIR button on the module. The LED on the module will flash quickly.
4. Hold the ON/OFF button on the remote for 3 seconds to pair with the dimming module. An audible beep indicates successful pairing.
5. Test the remote to confirm successful pairing. Up/Down buttons respond to individual presses and will not make continual adjustments if held down.
6. Once pairing is complete, slide the remote into the wall plate.
   Note: Removal of the remote will require removal of the wall plate.

Frequently Asked Questions (FAQ)

• How do I unpair a dimming module from a controller?
  To unpair, hold the PAIR button on the dimming module for 5 seconds. You will hear four beeps to confirm unpairing is complete.

• Can multiple lights be controlled with one dimming module?
  Yes, multiple lights can be controlled with one dimming module as long as the maximum load (10 A) is not exceeded.

Important: Read all instructions prior to installation.

Wireless Dimming System

Safety and Notes

• Product should be installed and serviced in accordance with applicable national, state, and local building and electrical codes.
• To reduce the risk of electric shock, ensure that the main power source and circuit breakers are switched off before performing any installation or wiring procedures.
• Each dimming module can be paired with up to five dimmer switches (WP4013). Dimmer switches can be paired with multiple dimming modules.
• Dimmer switches should be paired one at a time.

Specifications

General Specifications

Operating Temperature| -4°–104° F (-20°–40° C)
IP Rating| IP20
Radio Frequency| 433.96 MHz
RF Range| 98.4 ft (30 m)
WP4013 Specifications

Battery Type| CR2032 (x1 not included)

Check product label for specific electrical specifications related to installation. Improper installation will void warranty.

Dimming Module (PPA401S) Installation

1. With supply power off, connect wiring as shown in diagram.
   Note: Open knockout on fixture or junction box prior to this step if needed.

2. Mount dimming module.

3. Follow pairing instructions for intended controller (dimmer switch, WP4013). Note: To unpair, hold the PAIR button for 5 seconds. You will hear four beeps to confirm unpairing is complete.

Multiple lights can be controlled with one dimming module so long as the maximum load (10 A) is not exceeded. Dimming wires can be connected through conduit-side wires or external connector on controller body, but should not be connected to both simultaneously.

Dimmer Switch (WP4013) Installation

1. Being careful to avoid any live wires, install the full wall plate or adapter plate with the tab on the bottom side as shown.

2. Install CR2032 battery (not included) into remote, but do not install remote into wall plate at this time.

3. With dimming module powered on, press the PAIR button on the module. The LED on the module will flash quickly.

4. Hold ON/OFF button on remote for 3 seconds to pair with dimming module. An audible beep indicates the remote has been paired with the dimming module.

5. Test remote to confirm successful pairing.
   Note: Up/Down buttons respond to individual presses and will not make continual adjustments if held down.

6. Once pairing is complete, slide remote into wall plate.
   Note: Removal of remote will require removal of the wall plate.

Rev Date: V4 12/07/2023
4400 Earth City Expy, St. Louis, MO 63045
superbrightleds.com
866-590-3533

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>