StarTech com 160W-POWER-ADAPTER Universal DC Power Adapter User Guide

: March 18, 2024
: StarTech com

Table of Contents

160W-POWER-ADAPTER Universal DC Power Adapter
Package Contents
Connecting the Adapter to a Terminal Block
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

160W-POWER-ADAPTER
Universal DC Power Adapter
User Guide Universal DC Power Adapter – 24V, 6.6A Terminal Block

160W-POWER-ADAPTER Universal DC Power Adapter

Product ID
160W-POWER-ADAPTER

| Component| Function
---|---|---
1| Power Connector (side)| • Used to power the Adapter.
2| Terminal Block Wires| • Used to connect and power a Device.
• Two Conductor Terminal Block Connector Preinstalled
• Black Wire with Red + Flag = Positive
• Black Wire with White – Flag = Negative
• Output Voltage = 24V
• Output Current =6.6A 158.4W

Package Contents

Universal Power Adapter with 4ft [1.2m] Cable x 1
4ft [1.2m] Power Cords x4
Two Conductor Terminal Block Connector (Attached)
Three Conductor Terminal Block Connector
Quick-Start Guide

Requirements

Small Flat Head Screwdriver x 1
Device with a Two or Three Conductor Terminal Block Connector x 1

For the latest drivers, manuals, product information, technical specifications, and declarations of conformance, please visit: www.StarTech.com/160W-POWER-ADAPTER

Using the Two Conductor Terminal Block Connector

Plug the Two Conductor Terminal Block Connector on the Adapter into the Terminal Connector on the Device.
Note: Ensure the polarity of the input power is correctly matched with the Terminal Block Pins to ensure proper functionality. Refer to the Device’s vendor manual for further information on properly wiring the Device.

Using the Three Conductor Terminal Block Connector

Using a small screwdriver (Flat Head), loosen the screws on the Two Conductor Terminal Block Connector and carefully remove the Terminal Block Wires from the Two Conductor Terminal Block Connector.
Using a small screwdriver, loosen the screws on the Three Conductor Terminal Block Connector (included) and carefully insert the Terminal Block Wires into the Three Conductor Terminal Block Connector (Red Wire = Positive and Black Wire = Negative).
Note: Ensure the polarity of the input power is correctly matched with the Terminal Block Pins to ensure proper functionality. Refer to the Device’s vendor manual for further information on properly wiring the Device.
Tighten the screws on the Three Conductor Terminal Block Connector, to secure the Terminal Block Wires into the Three Conductor Terminal Block Connector.
Plug the Three Conductor Terminal Block Connector on the Adapter into the Terminal Connector on the Device.

Connecting the Adapter to a Terminal Block

Before terminating the Adapter make sure that the Adapter is disconnected from the Power Cord.
Refer to the vendor manual that came with the Device in order to properly terminate the Adapter.
Note: The Terminal Wires are Black Trim Wire = Positive and Black Wire = Negative.
The Output is 24V and the Current is 6.6A 158.4W.

Regulatory Compliance
FCC – Part 15
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by StarTech.com could void the user’s authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
Warranty Information
This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.

StarTech.com
Ltd.
45 Artisans Cres
London, Ontario
N5V 5E9
Canada| StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.| StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Rd,
Brackmills
Northampton
NN4 7BW
United Kingdom| StarTech.com Ltd.
Siriusdreef 17-27
2132 WT Hoofddorp
The Netherlands
---|---|---|---