MUNBYN IPDA089 Android Barcode Scanner with Large Screen 5.7 inch PDA User Manual

: May 15, 2024
: MUNBYN

Table of Contents

Product Overview
Packing Open and Installation
Operation
Contact us
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Android Scanner
User Manual
Version 1.00

MORE CHOICE FOR YOUR
GROWING BUSINESS
IPDA089

Product Overview

MUNBYN IPDA089 Android Barcode Scanner with Large Screen 5.7 inch PDA -
Product Overview

Packing Open and Installation

2.1. What’s in the box?
When you receive the package, open and check the packing list in the package.

MUNBYN IPDA089 Android Barcode Scanner with Large Screen 5.7 inch PDA -
What’s in the box

2.2. Install the SIM or Micro SD
Place the SIM card or Micro SD Card into the tray as shown. The take card pin is in the package.

MUNBYN IPDA089 Android Barcode Scanner with Large Screen 5.7 inch PDA -
Install the SIM or Micro SD

2.3. Using Battery
The IPDA089 uses a non-removable battery, after receiving it you can turn it on directly and use it, if you can’t turn it on please use the original power cable in the package to charge it for 30 minutes and then it will work normally.

Do not leave the battery unused for a long time, no matter it is in the device or inventory.
The lifespan of a Li-ion battery is around 2 to 3 years, the battery capacity will be lower after circularly charged about 300 times. (One full battery charge period means completely charged and completely discharged.)
If the battery is stored or not used for an extended period, be sure to follow the storage instructions in this document.
If the IPDA089 fails to power on or charge, this indicates that there is usually a problem with the battery. As the IPDA089 is not removable from the battery, we do not recommend that you carry out repairs personally, please contact our team of professional technical engineers (refer to section 5.0)
Store the battery at a temperatures between 5 °C and 20 °C (41°F and 68°F).

TIP: While charging, the device and the charger may become hot and stop charging. This usually does not affect the device’s lifespan or performance and is in the device’s normal range of operation.
For more solutions to battery woes, refer to Troubleshooting.

2.4. Charging the Device

The charger type is GME10D-050200FGu, output voltage/current is 5V DC/2A. The plug is considered as a disconnect device of the adapter.
Connect the device to the cable. The device turns on and starts charging. The charge/notiﬁcation LED is blue when charging and changes to a steady green when fully charged.

TIP: The standard battery charges from fully depleted to 90% in approximately seven hours and from fully depleted to 100% in approximately three hours. In many cases, 90% provides a signiﬁcant charge for everyday use. Depending on usage, a 100% charge lasts approximately 14 hours.

2.4.1. Battery Usage Tips

Do not use the battery in direct sunlight or smoky and dusty environments.
Do not strike, squeeze or step on the battery, nor throw it into liquid or ﬁre.
If the battery is deformed or damaged, replace it immediately.
Any product warranty is only valid if batteries supplied by MUNBYN.
Charging time should not exceed 24 hours. Over-charging or over-discharging may damage the battery.
Any product warranty is only valid if batteries supplied by MUNBYN.

2.5. Scanning
To read barcodes, a scanning-enabled application is required. The device contains the Keyboardemulator application. The function of the app is to allow the user to enable the scan processor, decode the barcode data and display the barcode content, outputting
the barcode to the corresponding open app.

Ensure that an application is open on the IPDA089 and that a text ﬁeld is in the cursor.
Place the top scanning head squarely on the barcode and press the scan button.

2.6. Screenshot
Capture an image of your screen. Your device will automatically create a Screenshots album in the Photos app.

Operation path: Scroll down the status bar > select the Screenshot function (if not on the ﬁrst page swipe right to go to the second page) > tap Screenshot

Operation

3.1. Barcode Scan (Data capture)
This section provides information on using the vari- ous scanning options and scanning barcode data.
KeyboardEmulator app is an internal software application to test barcode- scanning. Meanwhile, it can be used in some basic business scenarios depending on the customer’s choice. Please review this chapter for more information and details.
Please ensure that it is switched on before use.

When Enable Scanner is turning off, the following functions are can be setup:

Turn off this switch to conﬁgure the below items.
This ﬁeld represents your scan head model.
Please tick Barcode2D, which match for this IPDA089.
This area indicates your key setting, the default key value for the scan button is 139(Both of left and right button are same Key Code)

TIP: In use, when no light comes from pressing the button of the scanner gun, please check if the “Enable Scanner” is turn on.
Note: The 2D scan head can scan barcodes and QR codes, the 1D can scan barcodes, this is related to the conﬁguration you have purchased and not to the app settings.
If you are unable to use the scan gun keys after receipt, please follow the below steps:

a. Select the Barcode type that corresponds to your device.
b. Tap the input box, then press Scan Key/Pistol, the key-code will appear automatically.
c. Turning on the Enable Scanner.
After ﬁnishing the above steps, then you can use Scan Key/Pistol to trigger barcode-scanning.

3.1.1. Scan App Settings

MUNBYN IPDA089 Android Barcode Scanner with Large Screen 5.7 inch PDA - Scan
App Settings

Release key off scan: if you release the scan key, then scanning would stop.
Success Sound: if scanned successfully, there will be sound as a reminder.
Failure Sound: if failed to scan, there will be sound as a reminder.
Vibrate: if scanned successfully, there will be vibration as a reminder.
GS1 Parsing: it will enable parse GS1 code.
Block scan key: this is to block scan key-value, can leave it if it’s not necessary.
Barcode Not Repeat: In this mode, repeated barcodes will not show when scanning.
Reverse the data: Enable this item to reverse the scanning data.
Scan content on cursor: the data will show up in the place with cursor simultaneously.
Clipboard: read-out data will be saved in the clipboard, and can be pasted directly to anywhere with the cursor.
Broadcast Receiver: it is the method that uses the broadcast mechanism of Android to transfer data to the customer’s program.
Keyboard input: the data will show up together in the input box with the cursor.
Overlay cursor position: the scanner result will overlay the content before the cursor position.

TIP: If you encounter a situation where the barcode is not output in the app, please select the keyboard output mode as a priority, which will solve the problem.

Enter: Tick this checkbox, the output will be word-wrapping automatically.
TAB: The read-out data will be added with the tab character “\t” sufﬁx. when data is acquired in Excel, the cursor will move to the next cell automatically.

MUNBYN IPDA089 Android Barcode Scanner with Large Screen 5.7 inch PDA - Scan
data format settings

Preﬁx: The preﬁxing numbers or letters will be added to the front of the output. e.g.: If you input ‘ABC’, and the original barcode is ‘12345’, then the ﬁnal output will be as ‘ABC12345’.
Sufﬁx: The sufﬁxing numbers or letters will be added to the front of the output. e.g.: If you input ‘ABC’, and the original barcode is ‘12345’, then the ﬁnal output will be as ‘12345ABC’.
Remove the front number of characters: Input the number of characters you want to remove f rom the front.
Remove the back number of characters: Input the number of characters you want to remove from the back.
Filter data: It will be ﬁltered out the data you input.

** By clicking ‘Factory Data Reset’, the KeyboardEmulator app will reset to the original status.
Note:** If the IPDA089 does not produce light when the scan button is pressed or if other scan data is scanned after the setting, you can click on Factory data reset.

3.1.2. Barcode Settings
There are 4 items in this page:

Code setting
Firmware upgrade
Firmware version
Center Decoding Setting

MUNBYN IPDA089 Android Barcode Scanner with Large Screen 5.7 inch PDA -
2DSetting

3.1.2.1 Code setting
You can enable and conﬁgure the separate code in this page regarding your requirement, for example Code 128.

MUNBYN IPDA089 Android Barcode Scanner with Large Screen 5.7 inch PDA - Code
setting

3.1.2.2 Firmware upgrade
You can select a ﬁrmware ﬁle to upgrade in this page.
3.1.2.3 Firmware version
You can check the ﬁrmware version in this page which will help technical support to conﬁrm the information.
3.2. Network & Connect
This section provides manage connections between your device and a variety of networks and other devices.
3.2.1. Wi-Fi
You can connect your device to a Wi-Fi network to access the Internet without using your mobile data.

From Settings, tap Network & Internet –> Wi-Fi, and then tap to turn on Wi-Fi and scan for available networks.
Tap a network, and enter a password if required.
Tap Connect.

Connect to a Hidden Wi-Fi Network
If the Wi-Fi network you want is not listed after a scan, you can still connect to it by entering the information manually. Ask the Wi-Fi network administrator for the name and password before you begin.

From Settings, tap Network & Internet –> Wi-Fi, and then tap to turn on Wi-Fi and scan for available networks.
Tap + Add network at the bottom of the list.
Enter information about the Wi-Fi network:
Network name: Type the exact name of the network.
Security: Select a security option from the list, and enter the password if required.
View more: Deﬁne other advanced options, such as IP and Proxy settings.
Tap Save.

3.2.2. Mobile Networks
Use Mobile networks to conﬁgure your device’s ability to connect to mobile networks and use mobile data. Insert a SIM card before using it, Options may vary by carrier.
From Settings, tap Network & Internet –> Mobile networks.

Data roaming: Enable data roaming usage.
Preferred networks: Select the priority of sim cards or network type.
Preferred network type: Choose preferred Network type.
Access Point Names: Choose or add APNs, which have the network settings your device needs to connect to your provider.
Network operators: Choose available and preferred networks.

3.2.3. Bluetooth
You can pair your device to other Bluetooth-enabled devices. Once a pairing is created, the devices remember each other and can exchange information without having to enter the passkey again.

MUNBYN IPDA089 Android Barcode Scanner with Large Screen 5.7 inch PDA - Pair
new device

From Settings, tap Connected device –> Pair new device.
The Bluetooth will enable automatically, please pair the device from the list.

Rename a paired device
You can rename a paired device to make it easier to recognize.

From Settings, tap Connected device –> Bluetooth, and then tap to turn on Bluetooth.
Tap Device name to enter a new name, and then tap RENAME.

3.3. Reset Options
Reset network settings and app preferences. You can also reset your device to its factory defaults.

From Settings, tap System –> Reset options.
The following options are available:

Reset Wi-Fi, mobile & Bluetooth: You can reset Wi-Fi, mobile data, and Bluetooth settings with Reset network settings.
Reset app preferences: You can reset all app preferences settings and will not lose any app data.
Erase all data (factory reset): You can reset your device to factory defaults, erasing all data from your device.

This action permanently erases ALL data from the device, including Google or other account settings, system and application data and settings, downloaded applications, as well as your music, photos, videos, and other ﬁles.

3.4. Testing Tool
AppCenter is an internal software application to test the function of each module of the device(If you encounter any fault problems during use, you can use this app to check).

MUNBYN IPDA089 Android Barcode Scanner with Large Screen 5.7 inch PDA - App
center test list

3.4.1. Network test
From the AppCenter app, tap Network.
Tap Start to test Wi-Fi or Mobile signal by requirement.

3.4.2. GPS test
From the AppCenter app, tap GPS to access GPS information.

3.4.3. NFC test
From the App Center app, tap NFC to read or write ID/IC card, or write and reader block.

3.4.4 More Functional Module Tests
From the AppCenter app, tap About, tap Conﬁg to select functions.

MUNBYN IPDA089 Android Barcode Scanner with Large Screen 5.7 inch PDA - Test
function selection

3.5. FAQ

Problem	Cause	Solution
Can’t scan the code	Wrong scanning distance or angle.	Place the device

within proper scanning range or angle.
The scanner cant read the barcode.| Enable the type of barcode being scanned in the KeyboardEmulator. Refer to the Keyboard Emulator application.
Wrong barcode process mode.| Switch the input mode to the Keyboard input mode in the Keyboard Emulator application.
Scan keycode is incorrect.| Set the Scan keycode in KeyboardEmulator. Refer to the KeyboardEmulator application.
Wrong Scan setting.| Reset the KeyboardEmulator application and enable the Scanner again.
The device does not boot up| The power button was not pressed.| Hold the Power Key until the screen lights up.
The battery is not charged.| Charge the device.
System crash.| Perform a reset.
The device cannot be charge| The battery or device is faulty.| Connect with the USB cable and check the device’s LED light. If the LED lights up, the Battery is faulty, otherwise is the device’s problem.

3.6. Cautions

Strictly observe the following instructions while install and connect the device. Connect to stable power socket, try to avoid charging it together with high-power machines like air-conditioner.
Please try not to use the device during thunderstorm in case of lightening stroke, and power off as well as cut off its connection to host machine.
This is electrical product, be sure not let anything like pin, thumbtack, wire or water slip into the device, or short circuit will be caused to destroy device.
Be sure no heavy pressure on device or place anything on it.
Prevent ﬁerce vibration, strike or beat.
Ensure good working condition, never use it in humid, high temperature, sun burn, dustiness or frost environment, never get close to strong electromagnetic ﬁeld, never use device under ﬂammable and explosive conditions.
Avoid plug or swap any part or peripherals when power is on, or it may cause inner hardware damage. Shutoff device before cut power.
This device is integrated with Lithium battery, change our original battery if needed. Other types battery may cause damage to device. Contact us or our distributor when you need to change battery.
Cut off power and stop operation if device break down. Do not disassemble device yourself.
Avoid sleet, solar exposure, mechanical shock or extrusion. Be careful when delivering.
Device should be kept in original package, temperature of warehouse should be －20℃～60 ℃, relative humidity should be 5%～95%. No noxious gas, ﬂammable, explosive or mordant chemicals are allowed to be together, ensure no mechanical shock, impact or high magnetic.